ZyXEL Communications P-660HW-D Series User manual

P-660HW-D
802.11g Wireless ADSL 2+ 4-port Gateway
Quick Start Guide
Version 3.40
3/2006
Edition 1

P-660HW-D Series Quick Start Guide
2
Overview
The P-660HW-D is an ADSL router with a four-port built-in switch and IEEE 802.11b/g wireless capability.
See your User’s Guide for background information on all features.
How to use the included CD
This CD provides multi-media animations that help you set up your P-660HW-D.
1On the included CD, click Multimedia Auto Provisioner > Installation Tutorial.
2At the end of the tutorial, click Configuration Genie.
1 Hardware Connections
If you prefer to see a multi-media animation of how to make hardware connections, see the installation tutorial
on the included CD.
1DSL: Use a telephone wire to connect your P-660HW-D’s DSL port to a telephone jack (or to a splitter, if
one is already installed).

P-660HW-D Series Quick Start Guide
3
2ETHERNET: Use an Ethernet cable to connect a computer to the ETHERNET port for initial configuration
and/or Internet access.
3POWER: Use the power adaptor provided with your P-660HW-D to connect an appropriate power source
to the POWER socket. Make sure the power source is on.
4Push in the POWER button. Look at the lights on the front panel.
•ThePOWER light and the DSL light blink while your P-660HW-D starts up and stay on once the DSL connec-
tion is ready. The INTERNET light is on when you are able to access the Internet and blinks when the P-
660HW-D is sending or receiving data.
• Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected and blinks when
there is traffic.
If any of these lights are not on, check your connections, and inspect your cables for damage. If the lights are
still off, contact your local vendor.
2 Status Page
1In your browser, go to http://192.168.1.1.
2Enter the default password user to go
directly to the Status screen.
If your browser cannot find this screen,
check its security settings. See
Troubleshooting for details.

P-660HW-D Series Quick Start Guide
4
3See the User’s Guide for field descriptions of the Status screen.
3 Internet and Wireless Setup
1Open your web browser, and go to http://www.zyxel.com.
Your P-660HW-D tries to detect your Internet connection. Wait for the P-660HW-D to finish detection. If any
other screens appear, follow the directions in the screen.
If the web page opens correctly, your P-660HW-D is ready for you to use. If the web page does not open,
follow the rest of the steps. You should have the information provided by your ISP.
2In your browser, go to http://192.168.1.1.
3Enter the admin password 1234 to set up your internet and wireless connections and security settings.
Click Login. If your browser cannot find the login screen, check its security settings. See Troubleshooting for
details.

P-660HW-D Series Quick Start Guide
5
4Follow the directions in the screens.
5Click Go to Wizard setup. Then, click Apply.
6Click INTERNET/WIRELESS SETUP. Wait while your P-660HW-D tries to detect your DSL connection.
7Follow the directions in the wizard. Do not change default settings if your ISP did not provide information.
OTIST
ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically configure the
SSID and WPA-PSK on all OTIST-equipped wireless clients within range of the P-660HW-D.
Note: If you enable OTIST but select Disable wireless security using the wireless wizard, the P-
660HW-D will create a WPA-PSK automatically.

P-660HW-D Series Quick Start Guide
6
If you enable OTIST and select Manually assign a WEP key using the wireless wizard, the P-
660HW-D will replace the WEP key with a WPA-PSK.
Enable OTIST only if your wireless clients support WPA and OTIST.
You must enable OTIST on the P-660HW-D and all wireless clients within three minutes in any order.
To enable OTIST on the P-660HW-D, you can either use the wizard (see Section 3 on page 4) or hold in the
RESET button (see Section 1 on page 2) for one to five seconds. Do not hold the RESET button in for too long,
as this will reset the P-660HW-D to the factory defaults.
To enable OTIST on wireless clients, click Start in the Adapter screen. The Setup Key is 01234567 by default.
If you have previously saved a setup key on the P-660HW-D, use it instead of the default.
For more information, see Wireless LAN in the User's Guide.
Troubleshooting
1If you cannot access the web configurator using Internet Explorer in Windows XP or Windows Server 2003,
make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level
lower than High in Internet Explorer (in Internet Explorer, click Tools > Internet Options > Security >
Custom Level...). See the appendix in the User’s Guide for more information.
2If you cannot access the Internet when your computer is connected to the ETHERNET port, follow these
steps.
A) Check the lights on the front panel. If they are different than what is described in section 1, make sure
the connections are correct. (See section 1.) If the lights are still different, turn off the device, wait a few
seconds, and turn it on again.
B) Follow the steps in section 3again. Make sure you enter the correct information. For example, if your
account has a user name and password, make sure you type it correctly. In addition, if you are not sure
which encapsulation your ISP uses, contact your ISP.
C) If you are using a new Internet account, contact your ISP to make sure it is active.
D) If you still have problems, see Troubleshooting in the User’s Guide.
3If you cannot access the Internet using the wireless network, follow these steps.
A) On a computer in the wireless network, open your browser, and go to http://192.168.1.1. If you see the
screen in step 3of section 3, follow suggestions A- Dabove. If you do not, go to the next step.
B) Make sure your P-660HW-D and your computer are using the same wireless and wireless security
settings. Follow the steps in section 2.
Viewing Your Product’s Certifications
1Go to www.zyxel.com.
2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.
3Select the certification you wish to view from this page.