ZyXEL Communications Prestige 2602HW-C Series User manual

Prestige 2602HW-C Series
802.11g Wireless ADSL VoIP IAD
Prestige 2602HWL-C Series
802.11g Wireless ADSL VoIP IAD with Lifeline
Quick Start Guide
Version 3.40
3/2005

Prestige 2602HW Series Quick Start Guide
2
Overview
The Prestige 2602HW or 2602HWL ADSL VoIP IAD (Integrated Access Device) is an ADSL router with two
phone ports for Voice over IP (VoIP) calls. The Prestige also has a built-in switch and IEEE 802.11g wireless
capability. The Prestige 2602HWL’s lifeline feature adds regular phone services (that do not use the Internet).
See the User’s Guide for more information on all features.
The following figure shows your Prestige (A) connected to the Internet.
1 Hardware Connections
You need the following before you start:
Note: You may need your Internet access and voice account information.
Prestige Computer Telephone Power Adaptor
Ethernet Cable Telephone Cable

Prestige 2602HW Series Quick Start Guide
3
Do the following to make hardware connections for initial setup.
1DSL: Connect the Prestige to a telephone jack using the included telephone wire.
In the P2602HWL, the DSL port handles both the ADSL and regular
telephone service connections. Connect the included v-shaped cable (with
one gray wire and one green wire) to the P2602HWL's DSL port. Connect the
gray wire to the "modem" jack on a telephone or ISDN splitter (not included)
and the green wire to the splitter's "phone" jack or a telephone wall jack. This
is a FXO (Foreign Exchange Office) port.
Note: If you are using T-ISDN (UR-2), connect the green wire to the
(included) UR-2 to TAE connector before connecting it to the
telephone splitter's "phone" jack or a telephone wall jack.

Prestige 2602HW Series Quick Start Guide
4
2LAN: Use an Ethernet cable to connect a computer to a LAN port for initial configuration and/or Internet
access.
3 PHONE: Connect one or more analog telephones to these ports using telephone wires. These are FXS
(Foreign Exchange Station) ports.
4POWER:Use the included power adaptor to connect this power socket to an appropriate power source
(see the User’s Guide for power adaptors by region).
After you've made the connections, push in the power button to turn on the Prestige.
The PWR/SYS LED blinks during system testing and turns steady green if the testing is successful.
The LAN turns on if the LAN port is properly connected and blinks while sending or receiving data.
The DSL LED blinks during DSL line initialization and turns steady green when the Prestige has a DSL
connection.
The INTERNET LED turns steady green if the Prestige can access the Internet. It blinks when the Prestige is
sending or receiving data.
A PHONE LED turns steady green if a SIP account is registered for the corresponding PHONE port and blinks
when a call comes in or one of the connected phones is off hook.
•IfaPHONE LED is on, skip to Section 2.7 to see how to make calls through the Internet.
• If the INTERNET LED is on but the PHONE LEDs are off, go to Section 2.2 and access the web configurator.
Then go to Section 2.4 and configure the Voice Configuration wizard screen.
• If the INTERNET LED is off but the DSL LED is on, go to Section 2 to configure your Internet access settings.
• If the DSL LED is off, there is a problem with the hardware or the phone line connection to the ISP.
2 Initial Configuration
You may configure the Prestige for Internet access in any one of these ways:
• Zero Configuration

Prestige 2602HW Series Quick Start Guide
5
•Web Configurator Internet Access Wizard
2.1 Zero Configuration
Launch your web browser and
navigate to any web site (for
example, www.zyxel.com). The
Prestige automatically detects
and configures your Internet
connection. This may take about
two minutes.
If you have a PPPoE or PPPoA
connection, a screen displays
prompting you to enter your
Internet account information.
Enter the username, password and/or service name exactly as provided. Click Apply.
Note: Zero Configuration can only automatically configure the device for Internet access if you are
using PPPoE, PPPoA or ENET ENCAP encapsulation with a dynamically-assigned IP address
from your ISP. If you’re not using these Internet access settings, then access the web
configurator and use the wizard screens (see the following section) to configure your settings.
You also need to use the wizard screens if you want to configure the Prestige for making Internet
calls.
2.2 Web Configurator Access
1Launch your web browser. Enter 192.168.1.1 as
the web site address.
Note: If you do not see the next screen, then
please read Section 3.1 on page 12.
2Click Login (the default password 1234
is already entered).
3Type a new
password
(retype it to
confirm) and
click Apply.
You then see
the main web
configurator
screen

Prestige 2602HW Series Quick Start Guide
6
2.3 Wizard Setup
1In the Site Map screen, click Wizard Setup.
Note: Enter the Internet access information given to you by your ISP exactly in each wizard screen and
then click Next to continue or click Back to return to the previous screen.
Screen information is not saved when you click Back.
2From the Mode drop-down list box, select Routing (default) if you want to use routing features such as
NAT.

Prestige 2602HW Series Quick Start Guide
7
3The next wizard screen varies depending on the Encapsulation you chose in the first wizard screen. From
the Network Address Translation drop-down list box, select SUA Only if you have one public IP address,
Full Feature if you have more than one public IP address (for translation) or None to disable NAT.
Note: You will only see the next two screens in Routing mode.
4Fill in the fields with information from your voice service provider. Leave the default settings in fields for
which no information was provided (except if otherwise specified).
Note: You should have a voice account already set up.
This screen configures SIP account 1. Use the VoIP screens to configure SIP account 2.
•PPPoE
Select Connect
on Demand
when you don't
want the
connection up
all the time and
specify an idle
time-out period
(in seconds) in
the Max. Idle
Timeout field.
Select Nailed-
Up Connection when you want your connection up all
the time. The Prestige will try to bring up the
connection automatically if it is disconnected.
•ENET
ENCAP
• PPPoA • RFC1483

Prestige 2602HW Series Quick Start Guide
8
If you have a SIP account like 1234@VoIP-
provider.com,“1234” would be the SIP Number
and “VoIP-provider.com” would be the SIP Service
Domain.
REGISTER Server Address/Port: If you have no
registrar server information, copy what you
entered in the SIP Server Address/Port fields.
Caller ID: If you want to show identification
information when you make VoIP calls, select
Send Caller ID.
5Verify your
LAN, WAN and
SIP settings.
To change the
LAN settings,
click Change
LAN
Configuration;
otherwise click
Save Settings
to save the
configuration
and go to the
final wizard
screen. If you
change the
Prestige’s LAN
IP address,
you must use the new IP address if you want to
access the web configurator again.
6Click Save Settings in the screen shown in step
4 to go to the final wizard screen.The Prestige
automatically tests the connection to the
computer(s) connected to the LAN port(s). To test
the connection from the Prestige to the ISP, click
Start Diagnose. Otherwise click Return to Main
Menu to go back to the main screen.

Prestige 2602HW Series Quick Start Guide
9
2.4 Speed Dial Configuration
Click Voice in the navigation panel and then Speed
Dial to display the following screen.
Speed dial provides shortcuts for dialing frequently
used (VoIP) phone numbers.
You can use speed dial entries for peer-to-peer
calls or SIP numbers that use letters.
Select a speed dial key combination.
Enter the SIP number of the party you will call and
a name to identify them.
Select Use Proxy if calls to this party use your SIP
account.
Select Non-Proxy (Use IP or URL) if calls to this
party use a different SIP server or go directly to
the callee’s VoIP phone (peer-to-peer). Enter the
SIP server’s or the party’s IP address or domain
name.
Click Add.
2.5 Lifeline Configuration (Prestige 2602HWL)
With the Lifeline feature, you can use both VoIP and regular phone services.
Click Voice in the navigation panel and then
Lifeline.
PSTN Pre-fix Number: If you want to make a
regular call when the PWR/SYS LED is orange, dial
the prefix number that you configure here and the
phone number.
If the PWR/SYS LED is green or off, make regular
calls without a prefix number.
Relay to PSTN: Enter phone numbers that should
use the regular phone service (without the prefix
number). Do this for emergency numbers. The
numbers must be for regular phones (not VoIP
phones).
Click Apply.

Prestige 2602HW Series Quick Start Guide
10
2.6 Make Calls Through the Internet
When the VoIP LED turns on, your SIP account is registered successfully. Dial a numerical SIP number (like
“12345” for example) on your phone’s keypad.
Use speed dial entries for peer-to-peer calls or SIP numbers that use letters. Dial the speed dial entry on your
telephone’s keypad.
Use your voice service provider’s dialing plan to call regular telephone numbers.
2.7 Wireless Configuration
WPA-PSK encryption is preferred to WEP because it has user authentication and improved data encryption. If
you don’t have WPA-capable wireless clients, configure WEP encryption.
Note: Wireless clients and the Prestige must use the same SSID, channel ID, WEP or WPA-PSK key (if
enabled).
1Click the Wireless LAN link under
Advanced Setup.
2Click
802.1x/
WPA.Select
Authenticati
on
Required,
then select
WPA-PSK
and type a
Pre-shared
Key.
3Click Advanced Setup, Wireless LAN,
Wireless. In the ESSID field, enter up to 32
printable characters to uniquely identify the
Prestige.
If you didn’t configure WPA-PSK, configure
WEP in this screen (not visible if you’ve
configured WPA-PSK).