2easy DMR11-D8 User manual

- 1 -
DT 2-wire System
Quik Start Guide
ATTENTION:
This is an abbreviated Installation Manual, addressing
Wiring and Programming of the DT System only. For all
the detail information of DT 2-wire system, please refer
to the DT Technical Manual.
DT-ENG-QSG-V1 20091221

- 2 -
1.1. IN-OUT wiring without any distributor
Code=1, DIP-6=off
Code=31, DIP-6=off
Code=32, DIP-6=on
Code=2, DIP-6=off
ID=00
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
85~260AC
DPS PS5
1 2 3 4 5 6
ON
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
1
3
A
4
B
4
1 2 3 4 5 6
ON
CALL
UNLOCK
TALK/MON
IN-USE
4
5
2
1. System Wirings and Connections
Cable Usage A B
Twisted cable 2x0.75 mm260 60
Twisted cable 2x1 mm280 80
Cable Usage A B
Twisted cable 2x1 mm270 30
Twisted cable 2x1.5 mm270 50
When Monitor quantity < 20
When Monitor quantity > 20
[1]: Door Station, when there is only one Door Station,
the DIP bit-1 and bit-2 should be set to 00.
[2]: Power Supply(PS5), MUST be installed side by
side with the DPS unit.
[3]: Power Separator, MUST be installed side by side
with the PS5 unit.
[4]: Monitor, each one with a unique User Code
(Max.32 Monitors), the bit-6 of the DIP should be set
to 0 (off) if the Monitor is not at the end of the bus line.
[5]: Monitor, the bit-6 of the DIP should be set to 1 (on)
if the Monitor is connected at the and of the bus line.

- 3 -
1.2. IN-OUT wiring with DBC One-user distributor
ID=00
1 2 3 4 5 6
ON
85~260AC
DPS PS5
DBC
1 2 3 4 5 6
ON
Code=31, DIP-6=off
CALL
UNLOCK
TALK/MON
IN-USE
1 2 3 4 5 6
ON
Code=32, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
DBC
1 2 3 4 5 6
ON
Code=8, DIP-6=off
CALL
UNLOCK
TALK/MON
IN-USE
DBC
1 2 3 4 5 6
ON
Code=1, DIP-6=off
CALL
UNLOCK
TALK/MON
IN-USE
B
C
A
1
3
4
4
4
5
7
6
6
2
[1]: Door Station, when there is only one Door Station,
the DIP bit-1 and bit-2 should be set to 00.
[2]: Power Supply(PS5), MUST be installed side by side
with the DPS unit.
[3]: Power Separator, MUST be installed side by side
with the PS5 unit.
[4]: Monitor, each one with a unique User Code (Max.32
Monitors), the bit-6 of the DIP should be set to 0 (off) if
the Monitor is not at the end of the bus line.
[5]: Monitor, the bit-6 of the DIP should be set to 1 (on)
if the Monitor is connected at the end of the bus line.
[6]: DBC(DT Branch Controller) unit, each apartment
use one DBC unit to connect to the bus, except the last
apartmet at the end of the bus line.
[7]: DBC(DT Branch Controller) unit, at the end of
the bus line, can connect two apartments, the last
apartment and the 2nd last apartment.
Cable Usage A B C
Twisted cable 2x0.75 mm260 60 30
Twisted cable 2x1 mm280 80 40
Cable Usage A B C
Twisted cable 2x1 mm270 30 20
Twisted cable 2x1.5 mm270 50 30
When Monitor quantity < 20
When Monitor quantity > 20

- 4 -
1.3. Star wiring with 4 output distributor DBC-4
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
HI
HI
Code=32, DIP-6=on
Code=30, DIP-6=on
Code=31, DIP-6=on
Code=29, DIP-6=on
Code=4, DIP-6=on
Code=2, DIP-6=on
Code=3, DIP-6=on
Code=1, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
DBC-4
A B C D
IN
OUT
DBC-4
A B C D
IN
OUT
85~260AC
DPS PS5
ID=00
1 2 3 4 5 6
ON
A
C
B
1
3
2
4 4
4 4
4 4
6
5
4 4
[1]: Door Station, when there is only one Door Station, the DIP bit-1 and
bit-2 should be set to 00.
[2]: Power Supply(PS5), MUST be installed side by side with DPS unit.
[3]: Power Separator, MUST be installed side by side with the PS5 unit.
[4]: Monitor, each one with a unique User Code, note that all the bit-6 of
the DIP should be set to 1 (on) in this case.(Max.32 Monitors)
[5]: DBC-4(4 output Branch Controller) unit, the switch of the DBC-4
should be set to HI except the last one which is at the end of the bus
line.
[6]: DBC-4(4 output Branch Controller) unit, the switch of the DBC-4
should be set to 120 as it is at the end of the bus line.
Cable Usage A B C
Twisted cable 2x0.75 mm260 60 30
Twisted cable 2x1 mm280 80 40
Cable Usage A B C
Twisted cable 2x1 mm270 30 20
Twisted cable 2x1.5 mm270 50 30
When Monitor quantity < 20
When Monitor quantity > 20

- 5 -
1.4. Multi Door Station wiring
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
HI
ID=00
1 2 3 4 5 6
ON
ID=01
1 2 3 4 5 6
ON
ID=10
1 2 3 4 5 6
ON
ID=11
1 2 3 4 5 6
ON
DBC-4
A B C D
IN
OUT
85~260VAC
DPS PS5
Code=4, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
Code=3, DIP-6=on
Code=2, DIP-6=on Code=1, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
8
8
9
8
8
1
5
67
3
2 4
B
C
A
DPS-4
A B C D
BUS
[1]: The rst Door Station, the DIP bit-1 and bit-2 should be set to 00.
[2]: The 2nd Door Station, the DIP bit-1 and bit-2 should be set to 01.
[3]: The 3rd Door Station, the DIP bit-1 and bit-2 should be set to 10.
[4]: The 4th Door Station, the DIP bit-1 and bit-2 should be set to 11.
[5]: Power Supply(PS5), MUST be installed side by side with DPS unit.
[6]: Power Separator, MUST be installed side by side with the PS5 unit.
[7]: DPS-4(4 input Power Separator), can connect Max. 4 Door Stations.
[8]: Monitor, each one with a unique User Code, note that all the bit-6 of
the DIP should be set to 1 (on) in this case.(Max.32 Monitors)
[9]: DBC-4(4 output Branch Controller) unit, the switch of the DBC-4
should be set to HI except the last one which is at the end of the bus
line.
Cable Usage A B C
Twisted cable 2x0.75 mm260 60 30
Twisted cable 2x1 mm280 80 40
Cable Usage A B C
Twisted cable 2x1 mm270 30 20
Twisted cable 2x1.5 mm270 50 30
When Monitor quantity < 20
When Monitor quantity > 20

- 6 -
1.5. CCTV wiring with DCU
ID=00
1 2 3 4 5 6
ON
85~260VAC
DPS PS5
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
HI
DBC-4
A B C D
IN
OUT
Code=4, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
Code=3, DIP-6=on
Code=2, DIP-6=on Code=1, DIP-6=on
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
CALL
UNLOCK
TALK/MON
IN-USE
1 2 3 4 5 6
ON
DCU
AC
B
C
A
1
2
3
4
5
10 10
6
7
8 8
8 8
9
[1]: The rst Door Station, the DIP bit-1 and bit-2 should be set to 00.
[2]: Power Supply(PS5), MUST be installed side by side with DPS unit.
[3]: Power Separator, MUST be installed side by side with the PS5 unit.
[4]: DCU(CCTV Controller), can connect Max.2 CCTV cameras and
lamp/lock at the same time.
[5]: Light turn on button.
[6]: AC input for the lamp.
[7]: Lamp.
[8]: Monitor, each one with a unique User Code, note that all the bit-6 of
the DIP should be set to 1 (on) in this case.(Max.32 Monitors)
[9]: DBC-4(4 output Branch Controller) unit, the switch of the DBC-4
should be set to HI except the last one which is at the end of the bus
line.
[10]: CCTV camera.
Cable Usage A B C
Twisted cable 2x0.75 mm260 60 30
Twisted cable 2x1 mm280 80 40
Cable Usage A B C
Twisted cable 2x1 mm270 30 20
Twisted cable 2x1.5 mm270 50 30
When Monitor quantity < 20
When Monitor quantity > 20

- 7 -
2. Parts and Installations
2.1. PS5 - Power Supply
The PS5 power supply unit is designed for DT system to supply up to 32 Monitors and total 4 Door Stations at the same time.
• Universal AC input/full range.
• Multi protection: short sircuit, overload, over voltage
• Cooling by free air convection
• DIN rail mounting.
• Support up to 32 Monitors
• Support up to 4 Door Stations.
Dimension and Terminal
• L(AC): AC input.
• N(AC): AC input.
• : Earth Ground.
• V-: DC power output.(21.5~26.5 adjustable)
• V+: DC power output.(21.5~26.5 adjustable)
• VADJ: Output voltage adjustment.
• LED: Working state indicator.
Input Voltage: 85~260Vac, 120~370Vdc
Input Frequency: 47~63 Hz
Leakage Current: >2mA / 240Vac
AC current (TYP.) 1.5A /150Vac, 0.9A / 230Vac
Output VADJ range: 21.5~26.5 Vdc adjustable
Rated Voltage: 24Vdc
Rated Current: 3.2A
Rated Power: 76.8W
Electronic Specications
VADJ
LED
9
152.5
L (AC)
N (AC)
V-
V+
79
56
2-M3
1506.5
78
24
159
22 117
Unit: mm
9
81
83
DIN Installation
85~260AC
DPS
DIN nail
PS5

- 8 -
2.2. DPS - DT Power Separator
DPS: This unit is a power supply adaptor for the PS5 or PS4 power supply, it transfers the power from the power supply to the suitable
power for the non-polarity bus. Note that the DPS must work together with the PS5 or PS4 power supply.
2.3. DBC - DT Branch Controller
DBC: This unit is a single user distributor unit used to transfer all data between the Monitor and the Bus Line. Every Monitor(except the
last one at the end of the line) needs one DBC to connect to the Non-polarity Bus Line. No extra power supply needed, and one LED
indicator to show the working state.
Technical Specications(DPS)
Power input: 24Vdc (supplied by PS5)
Power output: 18Vdc
Power Consumption: 0.25W in standby, 0.5 W in actting
Working temperature: -5ºC +45ºC
Technical Specications(DBC)
Power Consumption: 0.25W standby, 0.5 W in working
Working temperature: -5ºC +45ºC
DPS
Connect to Door Station Connect to Monitor
Connect to
Power Supply(PS5)
Bus In/Out Bus Out(to Monitor)
DBC
Direct Wall Mounting DIN Rail Mounting
85mm
Use the screws to fasten the unit on the wall directly. Install on the DIN Rail.

- 9 -
2.4. DBC-4 - DT 4 output Branch Controller
DBC-4 (4 output Branch Controller)Distributor is a 4 output user distributor for DT system, to approach the star topology connection in
the apartment system. See Section 3 Cables and Connection for detail connection information.
2.5. DPS-4 - DT 4 input Power Separator
DPS-4 (4 input Power Separator)Unit is used to connect multi Door Stations, total 4 Door Stations can be connected to the DPS-4 unit.
In-use
Video Match
Power
ABCD
Trunk Bus
Bus Out Bus In
HI
120
set to 120 for the last DBC-4
on the building, the others
must be set to HI.
Connect to Monitors
DBC-4
ABCD
Trunk Bus
Connect to
Monitor/Distributor Connect to DPS
Connect to Door Stations
Direct Wall MountingDIN Rail Mounting

- 10 -
Jointer*2
Stopper
1 2 3 4 5 6
ON
L1
+12V T/R -
T/R+
LK - (GND)
CN-LK JP-LK
RS-485
SET
PA
PB
BUS
LK+(COM)
N.O.
EB+
EB -
L2
1
2
3
298.5 mm
114.5 mm
45 mm
Camera Angle adjustment
Open the mounting box of the panel, use a
cross screw to adjust the view angle of the
camera before installation.
Note
The double button line expansion panel can only
be connected to double button line Door Station;
the single button line expansion panel can only be
connected to single button line Door Station. For
example, the EP11/Dx can only be connected to
DMR11/Dx Door Station.
2.7. Door Station Mounting
Installation with expanding panel