2Y-LINK Technology CI-16-ASP-485 User manual

1
2Y-LINK Technology
Simplifies Installation of
High Quality CCTV System
Intelligent Model Signal Processor
User Manual
16 CHANNELS SIGNAL PROCESSOR CI-16-ASP-485
for transmission of Power, Video and Data(RS485)
with Built-in Power Pack

2
The package of 2Y-LINK Intelligent Model 16 Channels Signal Processor –
CI-16-ASP-485 contents :
Product contents
- One 16 Channels Signal Processor Unit
- One power cord (US, British, or EU)
- Signal Processor User Manual
Note : This package is only one part of CCTV installation package, must work with the
Associated Equipment for complete CCTV System.
Inspect the package and contents for visible damages. If any components are damaged or
missing, do not use the unit; contact the supplier immediately. If you need to return the unit,
you must ship it in the original box.
Installation Environment
Power : Ensure that the site’s AC power is stable and within the rated voltage of
the external power supply. If the site’s AC power is likely to have spikes or power dips,
use power line conditioning or an Uninterruptible Power Supply (UPS).
Ventilation : Install the unit in a well-ventilated area. Take note of the locations of the
cooling vents in the unit enclosure, and ensure that they are not obstructed.

3
Temperature : Observe the unit’s ambient temperature specifications when choosing a
location space. Extremes of heat or cold beyond the specified operating temperatures
limit may cause the unit to fail. Do not install the unit on top of other hot equipment.
Moisture : Do not expose the unit to rain or moisture. Moisture can damage the
internal components. Do not install this unit near source of water.
Associated Equipment
Push-Fit Mixer
Pig-Tail Mixer
DB-4PF Distribution Board for Four Cameras with Push-Fit Terminal
DB-4RJ Distribution Board for Four Cameras with RJ45 Sockets
CC-1RJ Cable Converter for Push-Fit Mixer
CC-1PF Cable Converter with Push-Fit Terminals
CC-2PF Cable Converter with Push-Fit Terminals
PF-ISO Ground Loop Isolator with Push-Fit Terminals
PT-ISO Ground Loop Isolator with Pig-Tail cables
PS-10KU Power Stabilizer
For instructions regarding the connection of the associated equipment in your system, please
consult the User Manual of the 2Y-LINK Intelligent Model 16 Channels Signal Processor –
CI-16-ASP-485 contents.
Qualified Person to install this equipment
This is not a DIY product.
Qualified personnel who is able to handle DC48V equipment and experienced in installation
of CCTV surveillance system is required.

4
Safety Precautions
ATTENTION : Installation should only be performed by
qualified personnel only in accordance with national Electrical
Code or applicable local code.
POWER DISCONNECT : Unit with or without “ON-OFF”
switches have power supplied to unit whenever the power cord
is inserted into the power source. However, the unit is in
operations only when the “ON-OFF” switch is in ”ON” position.
Disconnect the power cord to main power source is the safe
way to switch off the whole unit!
CAUTION : Do not try to open the case unless the power cord
is disconnected with the main power source.
This equipment is for indoor uses. DO NOT install near the fire
place or the place that the sun light can be directly reach.
WARNING :
TO PREVENT FIRE OR SHOCK HARZARD, DO
NOT CONNECT THE POWER CORD TO THE MAIN BEFORE
CAREFULLY READ THE USER MANUAL

5
2Y-LINK Intelligent Model Signal Processor
16 CHANNELS SIGNAL PROCESSOR CI-16-ASP-485
Contents
Chapter
Descriptions
Page No.
1 Introduction of 2Y-LINK Technology 6-7
2 Features of 16 Channels Signal Processor CI-16-ASP-485 8
3 Specifications of Signal Processor CI-16-ASP-485 and
Associated Mixers
9-10
4 Product Overview: 11-22
4.1 Signal Processor CI-16-ASP-485 11-22
4.2 Push-Fit and Pig-Tail Mixers 13
4.3 Accessories for Easy of Installation 14-20
4.4 Wiring Selection 21-22
5 Methods of Wiring Connections for 16 Channels Signal
Processor CI-16-ASP-485 for Power and Video Transmission
23-32
5.1 For Power and Video Transmission USING CAT.5
CABLE (One Cat.5 Cable for four Cameras)
23-25
5.2 For Power and Video Transmission USING CAT.5
CABLE and IN COMBINATION WITH BELL CBLE
(One Cat.5 Cable for four Cameras)
26-28
5.3 For Power and Video Transmission USING CAT.5
CABLE (One Cat.5 Cable for one Cameras)
29-30
5.4 For Power and Video Transmission USING BELL
CABLE
31-32
6 Method of Wiring Connections for 16 Channels Signal
Processor CI-16-ASP-485 for Power, Video and Data (RS485)
Transmission
33-39
6.1 For Power, Video and Data Transmission Using Cat.5
cable or in combination with bell cable
34-36
6.2 Transmission of Power, Video and Data for High Power
PTZ Camera (power > 8 W) with Isolator Using Cat.5
cable or in combination with bell cable
37-39
7 Brightness / Sharpness (Colour) Switch Adjustment 40-44
8 How to mount the Signal Processor to 19” Rack 45
9 Trouble Shooting 46

6
Chapter 1 Introduction of 2Y-LINK Technology
1.1 2Y-LINK Technology is a patented new concept, which has been successfully applied in
the CCTV surveillance system with multi-functions, such as power, video, two-way audio,
sensors, emergency signals and control data transmission, using a single pair of ordinary
Bell Cable or an unshielded twisted pair of Cat.5 Cables between the Mixer at camera side
to Signal Processor at DVR side.
1.2 It consists of a Mixer installed close to the camera and a Signal Processor
installed close to the DVR/Monitor. The transmission of power, video, two-way audio,
sensors, emergency signals and control data between Mixer and Signal Processor is
provided through a single pair of Bell Wires (AWG24-AWG18) or an unshielded twisted pair
of Cat.5 Cable, for distance of up to 2,000 meter (6,600 ft.), depending on the choice of
Signal Processor model together with the associated Mixer for the actual application in the
CCTV surveillance system.
1.3 The Signal Processor supplies power and transmits control data and audio signals
through the single pair of wires to the camera (applicable device) and at the same time
receives, through the same single pair of wires, video and other signals continuously from the
camera (applicable device) and channels them to the DVR/Monitor/applicable equipment.
1.4 The Mixer receives power and multifunctional data from the Signal Processor via the
single pair of wires, regulates/stabilizes them and distributes them to the camera/applicable
device and simultaneously transmits video and other signals back to the Signal Processor.
The following diagram shows examples of some typical applications of 2Y-LINK
Technology in CCTV surveillance systems using just one pair of cable.
2Y-LINK Technology for Multi-functions with a single pair of ordinary wire
Speaker
Microphone
Alarm O/P 1
Data Controller
DVR
monitor
Fire
Detector
Home automation
(Lighting,Air-conditioning...ect)
Alarm point 1
Microphone
Mixer
Power AC/DC Adapter
(not required for models with built-in Power Supply)
Door bell cable/
UTP cable/speaker cable
UP TO 2000m
Power
ideo
Data
Speaker
Camera
Alarm point 2 Alarm O/P 2
O/P or I/P
Home automation
(Lighting,Air-conditioning...ect)
Frie Alarm O/P
O/P or I/P
Multi-functional Applications Fig1.1
Control Station

7
Chapter 1 Introduction of 2Y-LINK Technology (continue)
Wide range of cables can be used for CCTV system installation.
A. One Cat.5 unshielded cable can connect four cameras, without interference with each
other
B. Bell cable/UTP cable from AWG24 to AWG 18 possible
C. Multi-core wire cable consists of several pairs of twisted or untwisted, shielded or
unshielded cable, like telephone cable, can be used without interference with each
other
D. Different cable types can be used in mixed combination to achieve easy installation
and cost reduction
E. Commonly used wires and cables adopted by 2Y-LINK Technology for
multi-functional application is shown in Fig 1.2.
Fig.1.2

8
Chapter 2 Features of 16 Channels Signal Processor CI-16-ASP-485
1. Video and Power transmission over one pair of UTP Cable or one pair of Bell Cable up to
1.5KM (5,000ft).
2. No expensive coaxial cable is needed.
3. No AC-main power point and No AC/DC adapter are needed for each Camera.
4. One Cat.5 cable can transmit both Power and Video Signals for four different cameras.
5. Maintains high quality Video with excellent interference immunity.
6. With built-in auto adjustment circuitry for various cable lengths to maintain high quality
Video Signals.
7. Much easier installation as compared with systems using coaxial cable.
8. Total cost savings of over 30% on installation as compared with other networking
systems.
9. As the Signal Processor is equipped with a built-in automatic voltage adjustment system,
there is no need to calculate the power line distance between the control centre and the
camera.
10. The Signal Processor is also equipped with built-in automatic-reset fault protection and
surge suppression protection for each channel, and the system is immunized from the
ground-loop effect.
11. Compatible with 2Y-Link Push-Fit or Pig-Tail Mixers.
12. The 2Y-LINK Intelligent Model SIXTEEN Channels Signal Processor – Model
No.CI-16-ASP-485 is also compatible with any DC 12V CCTV Camera up to
8W(680mA) with Video Output 1.0 Vpp 75 Ohm from any makers and produces equally
high quality pictures.

9
Chapter 3 Specifications of CI-16-ASP-485 and associated Mixers
2Y-LINK - Two wires link up with Leeds Intelligent Model Signal Processor and
Universal Mixers, and work well with different makers of CCTV cameras
Specifications for Signal Processor CI-16-ASP-485
NO. of Channel
16 Channels
Each Channel Video Output
1.0 Vpp 75 ohm
Band Width
10MHZ
Max. Distance/Channel
Specified for different Mixer Models up to 1,500 m
(5,000 ft.)
Each Channel connect port
Video Output to DVR/Monitor: BNC Plug
Video/Power I/O:
Front - RJ45 Sockets
Back - Terminals
Back – RJ45 Sockets (One Cat.5 cable for 4 cameras)
AC Power Main
AC 110V/60Hz,AC230V/50Hz
Operating Temperature
0
o
C ~ +40
o
C / 32
o
F ~ 104
o
F
Operating Humidity
10~80%
Case/Weight
STEEL / 3.4kg( 7.5 lb)
Dimensions
440mm(L)×280mm(W)×44mm(H)
17-5/16in.(L)×11in.(W)×1-3/4in(H)
Built-in Power Supply
(i) Maximum Power/Channel
(ii) Total Power for 16 Channels
(680mA/DC12V) for one Camera
(7,000mA/DC12V) for 16 Cameras
Fig. 3.1

10
Chapter 3 Specifications of CI-16-ASP-485 and associated Mixers (continue)
Specifications for Mixers
Video In (from camera) 1.0 Vpp 75 Ohm
Power Output for
Camera (up to 8W)
DC 12V 680 mA or
AC/DC 24V 340mA
As specified for the respective Mixer Model listed below
Band Width 10 MHz
Max. distance 1,500m (5,000ft)
Video Input to Mixer: Push-Fit Model - BNC Plug
Pig-Tail Model – BNC Socket
Power Supply to Camera:
Push-Fit Model-Terminal
Connect Port
Pig-Tail Model-DC plug
Operating Temperature -10
o
C ~ +50
o
C / 14
o
F ~ 122
o
F
Operating Humidity 10~95%
Case/Weight Push-Fit Mixers: Plastic/92g (0.2 lb)
Pig-Tail Mixers : Plastic/90g (0.2 lb)
Push-Fit Mixer : 65mm(L) × 35mm(W) ×32mm(H)
2
1
/
2
in. (L) × 1
3
/
8
in. (W) ×1
1
/
4
in. (H)
Pig-Tail Mixer : 67mm(L) × 35mm(W) × 22mm(H)
Dimensions
2
5
/
8
in.(L) × 1
3
/
8
in. (W) ×
7
/
8
in. (H)
Push-Fit Mixer Models:
- PF068A12 Mixer up to 500m(1650 ft.), DC 12V 680mA to camera)
- PF068B12 Mixer for 500-1,000m (1650-3,300 ft.),
DC 12V 680mA to camera)
- PF068C12 Mixer for 1,000-1,500m (3,300-4950 ft.),
Local Power to camera)
- PF068A24 Mixer up to 500m (1650 ft.),
AC/DC 24V 340mA to camera)
- PF068B24 Mixer for 500-1,000m, (1650-3,300 ft.),
AC/DC 24V 340mA to camera)
Pig-Tail Mixer Models
- PT068A12 Mixer up to 500m (1650 ft.), DC 12V 680mA to camera)
- PT068B12 Mixer for 500-1000m (1650-3,300 ft.),
DC 12V 680mA to camera)
- PT068C12 Mixer for 1000-1500m (3,300-4950 ft.),
Local Power to camera)

11
C05 C06 C07 C08C04C03C02C01 Power
C16C14C1 3 C15C09 C10 C12C11
C08
C07C06C05C04C01 C02 C 03
C12C11C10C 09 C16C15C14C13
BRIGHTNESS SHARPNESS SWITCH
CI-16-ASP-485
BRIGHTNESS
SHARPNESS
1245678 3 P in
+
++
+
-
RS485
+
++
+
-
Pin
387654 21
DATA CONTROL
ORANGE
RS485
1 2 3 4 4321 4321 4321 4321 4321 4321 4321
43214321432143214321432143214321
12 3 4
ORANGE
WHITE
TO MIXER
Chapter 4 Product Overview:
4.1 Signal Processor CI-16-ASP-485
Fig. 4.1.1 Front View
Fig. 4.1.2
For adjusting the
Brightness/Sharpness
(Colour) of the images
on the CCTV monitor
For connecting to Data
Control unit with Cat.5 for
controlling the movements
of PTZ Camera at Mixer
side
For connections to Mixer for
transmission of Power,
Video and Data Signals
using Cat.5 Cable.
To indicate that the AC power
switch is on and the power ,
fuse and AC power cord are
in proper working order.
For cooling the Power
supply the signal processor.
Usage or Purpose
Description
Icon
Item
4321
1234 1234 1234 1234 1234 1234 1234 1234
12341234123412341234123412344321
SHARPNESS
BRIGHTNESS
BRIGHTNESS SHARPNESS SWITCH
C13 C14 C15 C16C09 C10 C11 C1 2
C03C02C01 C04 C05 C06 C07 C08
RS485
DATA CONTROL
1245678 3 Pin
+
++
+
C11 C12C10C09 C15C13 C14 C16
C01 C02 C03 C04 C08C07C06C05
C09
C01
TO MIXER
ORANGE
WHITE
ORANGE
-
RS485
-
+
++
+
Pin
387654 21
Power
1
4
5
3
2
CI-16-ASP-485
Fan
Power LED Indicator
Video,Power,& DATA
with Camera LED
(RJ45 sockets)
RS485 Inlet
(RJ45 Socket)
Brightness/Sharpness
Switches

12
C09C10C11C12C13C14C15C16
+
++
+ +
++
+
DATA
CONTROL
CAMERA
PTZ
C04~C01C08~C05
C16~C13 C012~C09
Power OFF
ON
C08 C07 C06 C05 C04 C03 C01C02
180-260 ~ 50HzC16
C08 C01
C09
ONE CAT5
CABLE FOR
4 CAMERAS
Pin
38 7654 21
IDEO OUT
CABLE TERMINALS
TO MIXER
C02C03C04C05C06C07
C15 C14 C13 C12 C11 C10
RS485
FUSE:
RATED 3A
CAUTION
DO NOT OPEN
Chapter 4 Product Overview: (continue)
Fig. 4.1.3 BACK View
Fig. 4.1.4
Usage or Purpose
Description
Icon
Item
6
7
8
9
10
11
12
Power
ONE CAT5
CABLE FOR
4 CAMERAS
Pin
38 7654 21
C012~C09C16~C13
C08~C05 C04~C01
C16
C08 C01
C09
C02C03C04C05C06C07
C15 C14 C13 C12 C11 C10
+
++
+ +
++
+
DATA
CONTROL
CAMERA
PTZ
CABLE TERMINALS
TO MIXER
RS485
C16
C08
IDEO OUT
C02 C01C03C04C05C06C07C 08
C16 C15 C14 C13 C12 C11 C10 C09
Video Outlet
(BNC plug)
RS485 from Data
controller
(I/O Terminals)
Video & Power
(2-wire Terminals)
Video & Power RJ45
Socket
(4 Camera/per Socket)
Power LED
Indicator
Power Switch
AC Power Socket
with fuse
OFF
ON
FUSE:
RATED 3A
180-260 ~ 50Hz
CAUTION
DO NOT OPEN
For connecting to DVR or
CCTV Monitor
For connecting to Data
Control unit with Bell Cable
for controlling PTZ Camera
at Mixer side
For connections to Mixers
for transmission of Power,
and Video using Bell Cable
For connections to 4
Mixers/Cameras for
transmission of Power
and Video with one
Cat.5 Cable
To indicate that the power
switch is on and the AC
power,fuse and AC power
cord are in proper working
condition
AC Power ON/OFF Switch
Connecting AC Power Cord
to the Socket with built-in 5A
Fuse

13
-
+
Chapter 4 Product Overview: (continue)
4.2 Push-Fit and Pig-Tail Mixers
Push-Fit Mixer
Fig.4.2.1
Pig-Tail Mixer
Fig.4.2.2
Wiring connections of Push-Fit Mixer Wiring connections of Pig-Tail Mixer
Fig.4.2.3 Fig.4.2.4

14
CAT.5 CABLE
DB-4PF
Chapter 4 Product Overview: (continue)
4.3 Accessories for Easy of installation
4.3.1 Camera Distribution Boards
DB-4PF Distribution Board for four Cameras with Push-Fit Terminals
Fig. 4.3.1.1
Wiring connections of DB-4PF Distribution Board for four Cameras
with Push-Fit Terminals
Fig. 4.3.1.2
Orange/white
(Bridge wire)
Green/white
(Bridge wire)
CH4
CH3
CH2
CH1
SIGNALOUT
SIGNALIN

15
Connection to Camera
Green/white
(Bridge wire)
Orange/white
(Bridge wire)
CH1
CH2
CH3CH4
SIGNALOUT
SIGNALIN
CAT.5 CABLE
CAT.5
DB-4RJ
CAT.5
CAT.5
CAT.5
Chapter 4 Product Overview: (continue)
DB-4RJ Distribution Board for Four Cameras with RJ45 Sockets
Fig. 4.3.1.3
Wiring connections of DB-4RJ Distribution Board for Four Cameras
with RJ45 Sockets
Fig. 4.3.1.4

16
Chapter 4 Product Overview: (continue)
4.3.2 Cable Converters
CC-1RJ Cable Converter for Mixer with Push-Fit Terminals
Fig. 4.3.2.1
Wiring connections of CC-1RJ Cable Converter for Mixer with Push-Fit Terminals
Fig. 4.3.2.2
CC-1RJ
CAT.5

17
Chapter 4 Product Overview: (continue)
CC-1PF Cable Converter with Push-fit Terminals
Fig. 4.3.2.3
Wiring connections of CC-1PF Cable Converter with Push-fit Terminals
Fig. 4.3.2.4
CC-1PF

18
Chapter 4 Product Overview: (continue)
CC-2PF Cable Converter with Push-fit Terminals
Fig. 4.3.2.5
Wiring connections for CC-2PF Cable Converter with Push-fit Terminals
Fig. 4.3.2.6
+-
RS485
TO MIXER
Control Data
PS-10KU Power Stabilizer
ideo Signal
Cat.5 Cable

19
Chapter 4 Product Overview: (continue)
4.3.3 Power Stabilizer
For cameras with operation current up to 680mA, if those Cameras do not have stablising
circuit feature for a suddenly light change from a bright environment to dark environment a
PS-10KU power stabilizer is normally required.
PS-10KU Power Stabilizer
Fig. 4.3.3.1
Wiring connections for PS -10KU Power stabilizer to PF-Mixer
Fig. 4.3.3.2
Uncover
PS-10KU Power StabilizerPS-10KU Power Stabilizer

20
-
-
-
Chapter 4 Product Overview: (continue)
4.3.4 PF-ISO/PT-ISO Ground Loop Isolators
1. For camera power rating over 8W or exceed the power rating of the Signal Processor,
local power supply for the camera is required.
2. If local power is supplied to the camera, the potential differences between the camera
side and signal processor power point may occur and cause some moving horizontal
lines on the CCTV monitor screen. If this happens, a Ground Loop Isolator
(PF-ISO/PT-ISO) can be installed together with Mixer to eliminate the ground potential
differences and improve the quality of images shown on the CCTV monitor screen.
PF-ISO Ground Loop Isolator with Push-Fit Terminals
Fig. 4.3.4.1
PT-ISO Ground Loop Isolator with Pig-Tail cables
Fig. 4.3.4.2
Wiring connections for PF-ISO Ground Wiring connections for PT-ISO Ground
Loop Isolator with Push-Fit Terminals Loop Isolator with Pig-Tail cables
Fig. 4.3.4.3 Fig. 4.3.4.4
--
-