8 STREME 5310 User manual

5310
ver 19-01ENGLISH

EN
Congratulationsonthepurchaseof your new 8STREME5310pool cleaner.It isapowerfulautonomousrobot delivered
readyto use.Thisrobot comeswithan easyaccessibledebrisbasket alongwith floatingrotary couplingwhichlimitscable
entanglement.
Pleasecheck thepackageto makesurethat all partsareready to beinstalled.
Werecommend that youcheck theconnectionsof thecablesfrom thecleaner to thefloatingrotary couplingplug(chapter
5).If any partsaremissingor damaged,pleasecontact 8STREMEdirectly on www.8streme.eu
5310
Page2

EN
01Product features
02Warnings
03Packagecontents
04Start-up
05Cablesconnection
06 Adjusting Direction and Speed Control
07Cleaning thebasket
08Sidesuction
09Cleaning theimpeller
10Troubleshooting
11Sparepartslist
12Sparepartsdrawing
.................................................................... p04.
.................................................................... p04.
.................................................................... p04.
.................................................................... p05.
.................................................................... p07.
........................................... p08.
.................................................................... p09.
.................................................................... p10.
.................................................................... p10.
.................................................................... p11.
.................................................................... p14.
.................................................................... p15.
Tableofcontents
Page3

EN
MaximumDepth:2,50m
Maximumsizeof thepool:10mx5m
Input current:100-130VAC/ 200-230V AC
Output current:<24VDC
01Product features
1.5310 Roboticpool cleaner with floatingcord
androtarycoupling
2.Power transformer control box
3.Sampleof finefilter
03Packagecontents
01 PRODUCT FEATURES/ 02 WARNINGS/ 03 PACKAGECONTENT
Page4
02!!Warnings !!
2.1 Please refer to therulesof your country
regardingswimmingpool safety.
2.2 Placethepower transformer at least 3.5 m
fromthepool.
2.3 Makesurethat your electrical outletsare
properly grounded.
2.4 Please makesurethat your electrical
systemiswell protectedby a30mA
ground fault circuit interrupter (GFCI)
2.5 Keep thepower transformer away from
moisture.
2.6 Donot usethe robot out of thewater.
2.7 Makesurethat thetransformer is
disconnectedbeforeperformingmaintenance
ontherobot.
2.8 Don't use any damaged power cableor cord.
2.9 Do not usetherobot if peopleareinthe
pool.
2.10 Do not usetheswimmingpool whenthe
cleaner isinthepool.
2.11 Removetheroboticcleaner from the
swimmingpool whennot in use.
2.12 Theuse of therobot should bein apool
whosetemperatureisbetween5 and36°C.
2.13 Do not usetherobot if you havea
counter-current swimmingdevicerunning.

EN
04 Start-up
* YOURCLEANERROBOT COMESPRE-ASSEMBLED IN THEBOX.
-Our robotsaredesignedto facilitatethe
maintenanceof your pool. However,theyarenot
intended to clean apool full of algaeandleaves
(ex:end of winter period).
In thiscase youmust: usetheleaf skimmer,
cleanthefilter andput back onthefilter and
thepump.
-To removethecleaner fromyour pool,lift the
cableslowly and gently until youcan grabit by
thehandle.Usethehandletofully pull out the
cleaner
QUICKFACTS
04 START-UP
Page5
4.1 Placeyour power boxto amidpoint between
thetwo endsof your pool and at least 3.50 m
fromtheedgeof thepool.
4.2 Placethe robot in your pool and wait until it is
completely submerged.If necessary,helpit to
sink manually.
Transformer
5310 robot
Rotary couplingdevice

EN
4.6 For optimal performance,placeyour robot in
thepool at thefurthest possiblelocationfrom
thepower source.
Thisistheappropriatelength of thecableso
that therobot can reachall of your pool.
Limit thelength of cablein thepool to the
bareminimum,andplacethesurplusoutside
thepool.
04 START-UP
4.8 To turn off your robot,pressthepower button
4.9 Donot removeyour robot out of water
immediately after theendof itscleaningcycle
so asnot tocauseatemperatureshock.
4.10Whenthecleaner isnolonger usedfor an
extendedperiod,storeyour
robot indoors.
*If red or bluelightsblink,checkthe
troubleshootingsection
Page6
4.4 Screw the nut of thefloatingcablefirmly.
4.3 Insert theendof thefloatingcableinto the
socket.Takenoteof theorientationof the
plugand socket.
4.5 Pressthe switchon thehousingof the
transformer under bluelight.Thiswill activate
thepower source.

NOTE:
Leavingtoomuchcableinthepool will limit theeffectivenessof thefloatingrotarycouplingjoint
andresult infaster cableentanglement.
EN
05Cablesconnection
Whenyou connect therobot to thefloating
rotarycoupling,removethesleeveto exposethe
blueplug.
Matchthenotchinthepivot (FigA) Insert and push theblueplug(FigA thenB ).
1.Sleeve 2.Blueplug 3.Blacknut
04 START-UP / 05 CABLESCONNECTION
Pushthesleevetotheend. Tightentheblack nut (fig.D)on the floating
rotarycouplingbyhand. Page7

EN
06 ADJUSTINGDIRECTION AND SPEED CONTROL
Page8
06AdjustingDirectionandSpeedControl
6.2 To adjust thespeed of therobot,slidethe
redtabat the bottomof outlet cover.
Slidingtotherabbit increasethespeed
and to theturtledecreasesthe speed.
6.1 Toadjust thedirection of the robot,rotatethe
outlet cover.Thedirectionof therobot will be
determined by theposition of the indicator.
Note :withindicator onvertical position,therobot
will go straight ahead. With indicator turned right,
therobot will go left.With indicator turnedleft,the
cleaner will go right.
6.3 For most pools,it isrecommended that theoutlet cover at both endsdo
not sharethesamedirection.
For best performancehaveoutlet at thehingeendof thecleaner be
straight andthentheoutlet at thefront of thecleaner rotated
NOTE:
Thesearerecommendedsettings. Dependingontheshapeandsizeofyour pool,
youmayhavetoplayondirectionandspeedadjustmentstoreachtheoptimizedsettingfor your pool

EN
07 CLEANINGTHEFILTERBAG
Page9
7.1 Pressin thebutton at the front of thecleaner
andlift up thetop shell.Continueto
lift uptheshell until you hear a?click?at the
hingeandtheshell staysin place.
07Cleaningthefilter bag
7.5 Dumpout the debrisinsidethe bag.Usea
hoseto spray water and clean thebag.
7.2 Pull back thered tabsononesideand
completely lift upbagframeonthat side.
7.4 Pull off the elasticbandon the bagfrom frame
7.3 Repeat for oppositeside.
7.6 Wrapelasticbandof bagback onto theframe.
Alignthered ribbon withthetabof theblack
plasticframe.
Pull back theredtabsand push theframe
back into theopening.Theframeisall the
wayinwhenthetabsaresittingon topof
theframe.

EN
08Sidesuction
08 SIDESUCTION / 09 CLEANINGTHEIMPELLER
Page10
NOTE:
A pair of sidesuction flapis
provided to increasethe
vacuumpathwidthupto45cm.
Usethissidesuctionflapsonly if
your pool hasgoodflat bottom
without pool liner pleats
otherwisewill slow downthe
pool cleaner robot significantly
or evenstopthecleaner robot
frommoving. 8.1:Flipthepool cleaner robot
upsidedown 8.2:Placetheflapsonto thepool
cleaner robot asshown. 8.3:Thentight it up by thescrew provided
09Cleaningtheimpeller
NOTE:
Somedebriscan clog or be
wrapped around theimpeller of
thepump.Byforce,thesedebris
can hinder theproper
functioning of therobot or even
damagetheengine.
Regular visual inspection ispart
of thenormal maintenanceof the
robot.
9.1:Removetheflapassembly
tocleanthedirt or hair on
impeller
9.2:Useaflat screw driver toply
theflap assembly out asshown 9.3:Snaptheflap assembly back after cleaning

EN
PROBLEM
Therobot floatson thesurface.
Therobot doesnot clean all areasof the pool.
Therobot doesnot recover debrisduringoperation.
Fineparticles(dust or dirt,pollen...)areejectedby
theimpeller.
- Immersion of the robot in thepool.
- Use of thefinefilter.
-Not enough / too muchcablefloatinginthepool.
- The robot doesnot receive enough power.
- Basket clogged/ full.
- An object isstuck in the impellersor the grids
located in front of theimpeller.
- Debrisare too fine,therobot ismadeto pick up
theparticlesmorethan50microns(with thefine
filter insidethebasket).
CAUSE(S)
-Whenyouput therobot inthepool,let it sink and
reach the floor before youturn it on.
- If you useanoptional finefilter,removethefilter
fromitsplasticwrap,immersethefilter in thewater
so that it isalreadywet beforeyou put it in therobot
andlet therobot settleonthefloor beforeyou
turn it on.
-Makesurethelength of floatingcableintroduced
in the pool isjust the required length.
- Removeany excesscablelength fromthepool and
leave thisexcesslength outsidethepool next to the
power supply box.
- Insert therobot at the center point of thepool.
If your pool isoval or rectangular,thispoint isthe
middleof thelength.
- Check theconnection of the cables.
-Cleanthebag.Clean thefine
filter if you use thisaccessory.
-Checkif thebasket isproperly inserted.(See
chapter Cleaning of thefilter bag).
-Checkthat therearenoforeignobjectsin the
impellersor blockedinthegridinfront of the
impellers
-Checktheattachment of thebasket,pressit if
necessary to lock it.
- Use afinefilter (check item number on theparts
drawing17,sku51390 filters)onthe
other handdo not forget that it isthefiltration of
your swimmingpool whichensuresthecleaningof
theparticlesof lessthan50 microns.
SOLUTION(S)
10TROUBLESHOOTING
10 TROUBLESHOOTING
Page11

EN
Therobot movesinonedirection
Therobot doesnot moveandthefiltrationpump
doesnot work either.Therobot doesn't work any
longer.
Thepumprunsbut therobot doesnot move.The
robot turnsonbut staysonthespot.
Therobot stopsafter afew minutes
-Anobject blockstherollers,thewheelsof therobot
or interferingwith themovement of therobot.
-Therobot isnot connectedto apower source.-
Power off
-No/ not enoughpower istransmittedto therobot
- An object blocksthe rollers,.
-Possibility of motor problem
-Connectionof thefloatingcable
-Possibility of fault of thefloatingcable
-Possibility of motor leakage
-Unplugpower supply and takerobot out of water.
Openthecleaner to inspect thecleaner.
-Checkthat thereareno foreignobjectsinthe
impellers.
-Check that thereareno foreign object blockingthe
rollerslocatedbelow thecleaner.
-Checkthat thepower sourceisactiveby plugging
another deviceinto thepower outlet.
- Check that the power supply isturnedon.
- Check all connectionsof therobot to thepower
source.
-Checkthat thereareno foreignobjectsinthe
impellers.
-Unplugthepower and takeout therobot inthe
water.Openthecover of thebasket andremovethe
basket.
-Checkthat therearenoforeignobjectsin the
impellers.
- Check that therearenoforeignobject blockingthe
rollerslocatedbelow thecleaner.
-Contact theAfter-salesService
-Checktheconnection of thefloatingcable.
Disconnect and reconnect asneeded.
-Checkthestatusof theconnectorsat theendsof
your cables(damaged,rusted,etc.)
PROBLEM CAUSE(S) SOLUTION(S)
10 TROUBLESHOOTING
Therobot movesslower thanbefore -Therobot istooheavy - Theflow isnot sufficient
-Cablesconnections
-Checkthebagandclean it if necessary.
-Checkthat thereareno foreignobjectsinthe
impellers.
-Check that thereareno foreign object blockingthe
rollerslocatedbelow thecleaner.
-Checkthestatusof theconnectorsat theendsof
your cables(damaged,rusted,etc.)
Page12

EN
- Check all theelectrical connections(seechapters
on theelectrical connections).If moisture is
present onthefittings,let drybeforeconnecting
thefittingsagain.
- Theelectrical current doesnot reachtherobotThelightsflash oneafter theother
Redlight flashes.
No ledlit on thetransformer
TheredandblueLEDsflash simultaneously
-Badconnection
-Possibility of motor problem
-Nocurrent iscoming
- Theelectrical connectionismadeto therobot,but
thediagnosticsystemdetectsaproblem.
- Check all theconnectionsof thecables
-Contact theAfter-salesService
- Check your electrical outlet
- Check theconnections
-contact our Customer Service
- Check if the connectionsare correct and tight.
If theproblempersists,pleasecontact your dealer
or our Customer Serviceat [e-mail]
Pleasecontact www.8streme.eu if you haveanyother questions.
Checkout ourYouTubeChannel for informativevideos!
https://www.youtube.com/channel/UC8gnxUkHLdbVbkhdr5M4ZLw/playlists
PROBLEM CAUSE(S) SOLUTION(S)
10 TROUBLESHOOTING
Page13

EN
DRAWING:ITEM NUMBER SKU PART DESCRIPTION
11Sparepartslist
11 SPAREPARTSLIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
51331
51240
51120
51302
51350
51313
51151
51342
51050
51412
51000
81000
30160
33130
33210
51001
51390
Curvedhandleset.Left andRight.Black
Pumpoutlet flapassembly.Black
Pumpmotor
Topshell.Black
Latchlock.Grey
Bottomchassis.Black
Sidewheels.Grey.4 pieces
Quick drainflap.Black
Roller tubes.2 pieces
Sidesuction flaps.Black.2 pieces
Debrisbasket
Door hingeset
Power supply.Dual timer
10mfloatingcord with rotary coupling
Robot endfloatingcord.Grey
Filter screen
Finefiltrationreplacement kit
Page14

EN
12 Sparepartsdrawing
12 SPAREPARTSDRAWING
Page15