A1 Security Cameras BN481E82 User manual

Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
BN481E82
Eight-channel Network Recording Kit
❶ UNPACKING
Your system includes the following: ❷ CONNECTIONS Camera ConnecƟons
Cameras
• 8 x Netowrk Dome Cameras
• 8 x Hardware Packs, with:
MounƟng Template,
Expansion Bolts (3),
Self-tapping Screws (3), Hex Wrench,
Startup Guide, and SoŌware CD
Network Video Recorder
• 1 x 8-channel NVR, with:
Pre-installed 2 TB HDD,
AC Power Supply,
Ethernet Cable, Mouse, 1 Video Output Ethernet, RJ-45
Hard Drive SATA Cable, HD Hardware, 2 Power Input 12 VDC or PoE (IEEE 803af)
Startup Guide, and SoŌware CD
DIMENSIONS INSTALLATION
❹ Camera and NVR ❺ Mount and Make ConnecƟons
375.0 mm
(14.80 in.)
53.0 mm
(2.10 in.) • Ensure the wall or ceiling can support 3x the weight of the
camera.
327.50 mm
(12.90 in.) • If you are connecƟng the IP cameras to the PoE ports of the
NVR, DO NOT connect a 12VDC power supply to the cam-
era. Power will be supplied to the camera via PoE. Proceed
directly to the next step.
CONNECTIONS
❸ NVR ConnecƟons
1 100 to 240 VAC Power IN 6 Audio IN/OUT
2 On/Off BuƩon 7 VGA OUT
3 PoE, RJ45 (x8) 8 Alarm I/O
4 Network Switch, RJ45 9 HDMI OUT
5 USB Port 10 Ground
INSTALLATION
❻ Waterproof the Network Connector
• Place the wide side of the rubber ring onto the end of the
network cable extending out from the camera.
• Thread the cable through the Fixing Rubber Ring and the
Waterproof Locking Cover.
• AƩach the male Ethernet connector to the network cable
coming from the camera.
• Connect the other end of the waterproof connector to the
network port and rotate it clockwise to lock the network
port and waterproof connector firmly.
• Slide the Waterproof Locking Cover over the main body of
waterproof connector and rotate it clockwise to seal the
connecƟ on

Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
BN481E82
Eight-channel Network Recording Kit
INSTALLATION
PosiƟon the Camera
❼ INSTALLATION
Place the NVR
❽ INSTALLATION
Connect Cameras and Peripherals
❾
• Loosen, but do not remove the set screws on either side of
the bracket that holds the camera.
• Tilt the camera to adjust the Ɵlt angle (0° to +65°). Tighten
the two locking screws on the bracket to lock the Ɵlt angle.
• Turn the camera module to adjust image pan orientaƟon
(0° to +355°).
• Turn the camera base to adjust the rotaƟon of the camera
(0° to +355°).
• Ground the unit using the ground connecƟon of the power
supply to protect the unit from damage, especially in damp
environments.
• Protect the plug and power cord from foot traffic, being
pinched, and its exit from the unit.
• Do not place the unit in a wet, dusty, extremely hot or an
extremely cold environment; and avoid environments with
strong electromagneƟc radiaƟon.
• Connect an Ethernet cable to the RJ45 port for network
access.
• Connect the incoming network cables from the eight net-
work cameras.
• Connect a VGA or HDMI cable to the rear panel and to the
display monitor.
• Connect the NVR to a 100-240 VAC power supply and turn
on the device using the On/Off buƩon.
OPERATION
Log in to the NVR
❿ OPERATION
Add Cameras with Smart Add
⓫ OPERATION
View Live Video
⓬
• When the network cameras and the NVR are connected to
• Set the Username and Password aŌer iniƟal start-up. same router or switch, you can use the Smart Add funcƟon
• Supply the default password (“admin”) for the Admin to add all network cameras to the NVR at the same Ɵ me
user.
• Default IP Seƫngs
• Supply a new password.
IP Address 192.168.1.108
Subnet Mask 255.255.255.0
Gateway 192.168.1.1
• Click Live in the Main Menu.
• Supply answers for two confirmaƟon quesƟons in case the • Change the Live screen grid if more camera channels are
password has to be reset. desired.
• AŌer Admin Security is set, supply the Username and the
new Password.
Rev. 001.005. Copyright © 2017 Dahua Technology. All rights reserved. Information contained in this document is subject to change without prior notice. Dahua does its best to provide accurate information, but cannot be held responsible for typos or mistakes.