Aaeon PCM-6890 User manual

Quick Installation Guide
PCM-6890 Installation Guide 1
PCM-6890
Notice:
This guide is designed for experienced users to
setup the system within the shortest time. For
detailed information, please always refer to the
electronic user's manual.
Safety Precautions
PCM-6890
All-in-One Socket 370 Celeron Single Board Computer
with LCD, Ethernet, Audio, & 4 COMs
Part no. 2007689000 1st Ed. Printed in Taiwan May 1999
Quick Installation Guide
Warning! Always completely disconnect the power cord
from your chassis whenever you work with the
hardware. Do not make connections while the
power is on. Sensitive electronic components
can be damaged by sudden power surges. Only
experienced electronics personnel should open the
PC chassis.
Caution! Always ground yourself to remove any static
charge before touching the CPU card. Modern
electronic devices are very sensitive to static
electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all
electronic components in a static-dissipative
surface or static-shielded bag when they are not
in the chassis.
PCM-6890

PCM-6890
2PCM-6890 Installation Guide BC-599/596
Locating jumpers
SW1
J5
J9
J8J10
J1
J2
J7
J6
J3
J4

Quick Installation Guide
PCM-6890 Installation Guide 3
PCM-6890
Locating connectors
CN1
CN2
U18
CN6
CN8
CN7
CN17
CN13
LED2
CN17
CN15
CN14 CN16
CN9
CN10
CN4
CN11
CN16CN14 CN12CN15

PCM-6890
4PCM-6890 Installation Guide BC-599/596
Jumpers and connectors
Connectors on the board link it to external devices such as hard
disk drives, a keyboard, or floppy drives. In addition, the board
has a number of jumpers that allow you to configure your system
to suit your application.
The following tables list the function of each of the board's jumpers
and connectors.
Jumpers
Label Function
J1 Clear CMOS
J2 System temperature thermal sensor
J3 COM4 RI pin voltage select
J4 COM3 RI pin voltage select
J5 Audio output select
J6 ATX soft-power switch connector
J7 COM2 RS-232/422/485 select
J8 LCD clock select
J9 LCD driving voltage select
J10 COM2 RS-232/422/485 select
SW1 (4~6) CPU frequency ratio
SW1 (2~3) DOC address select

Quick Installation Guide
PCM-6890 Installation Guide 5
PCM-6890
Connectors
Label Function
CN1 CPU fan power connector
CN2 PC/104 connector
CN3 USB ports connector
CN4 CD-ROM signal input connector
CN6 IDE drive connector
CN7 Front panel connector
CN8 IrDA connector
CN9 ATX power connector
CN10 LCD display connector
CN11 Keyboard and PS/2 mouse connector
CN12 VGA display connector
CN13 Audio connector
CN14 Printer port connector
CN15 100Base-Tx Ethernet connector
CN16 Serial ports connector
CN17 Floppy dirve connector
U18 DiskOnChip socket
LED2 Ethernet Tx/Rx/Link LED connector

PCM-6890
6PCM-6890 Installation Guide BC-599/596
COM3/COM4 RI pin voltage select
(J3, J4)
The 9th pin of COM3 and COM4 (9-pin D-sub connector) can be
selected as RI, +5V, or +12V by setting J3 & J4.
COM3 RI pin setting (J4)
RI* +5V +12V
J4
COM4 RI pin setting (J3)
RI * +5V +12V
J3
*default
Clear CMOS (J1)
You can use J1 to clear the CMOS data if necessary. To reset the
CMOS data, set J4 to 2-3 closed for just a few seconds, and then
move the jumper back to 1-2 closed.
Clear CMOS (J1) Protect* Clear CMOS
J1
*default
1
2
3
1
2
3
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6

Quick Installation Guide
PCM-6890 Installation Guide 7
PCM-6890
ATX Soft-Power Switch connector
(J6) The ATX Soft-Power switch connector is a 2-pin header. Locate
the power switch cable from your system. It is a 2-pin female
connector. Plug this connector to the Soft-Power switch connector
marketedJ6.
Audio output select (J5)
You can select the output mode of onboard audio connector
(CN14) by setting J5.
"Speaker out" is the output signal amplified by onboard amplifier
Audio output select (J5)
Line out * Speaker out
J5
*default
2 1
4 3
6 5
2 1
4 3
6 5

PCM-6890
8PCM-6890 Installation Guide BC-599/596
COM2 RS-232/422/485 select (J10, J7)
ThePCM-6890 COM2 serial portcan be selected asRS-232, RS-422,
or RS-485 by setting J10 & J7.
COM2 Select (J10, J7)
RS-232* RS-422 RS-485
J10
J7
*default
1 4 7 10
3 6 9 12
1 4 7 10
3 6 9 12
1 4 7 10
3 6 9 12
1 3 5
2 4 6
1 3 5
2 4 6
1 3 5
2 4 6

Quick Installation Guide
PCM-6890 Installation Guide 9
PCM-6890
J8
LCD clock signal select (J8)
You can select the LCD control signal by setting J8. The following
charts show the available option.
LCD clock signal select (J8)
SHF CLK * ASHF CLK
*default
1 2 3 1 2 3
J9
LCD driving voltage select (J9)
You can select the LCD connector CN10 (pin 5 and pin 6) driving
voltage by setting J9. The configurations are as follows:
LCD driving voltage select (J9)
5V 3.3V *
*default
1 2 3 1 2 3

PCM-6890
10 PCM-6890 Installation Guide BC-599/596
SW1 (4~6) CPU frequency ratio
CPU core frequency = CPU frequency ratio (2~5.5) * External bus
clock(66or100MHz)
UPC YCNEUQERF OITAR )4(1WS)5(1WS)6(1WS
X2NOFFOFFO
X5.2NOFFONO
X3NONOFFO
X5.3NONONO
X4FFOFFOFFO
X5.4FFOFFONO
X5FFONOFFO
X5.5FFONONO
*
* default
Note:
Most Celeron CPUs' frequency ratio are pre-locked
within the CPUs. These CPUs run at fixed speed
(frequency)regardlessoftheconfigurationslistedabove.
IftheCPUyouare using requires higher ratiothen5.5X,it
is most likely pre-locked.