ABB Relion 620 Series User manual

Relion® 620 series
Motor Protection and Control
REM620
IEC 60870-5-103 Point List Manual

Document ID: 1MRS757657
Issued: 2013-05-07
Revision: A
Product version: 2.0
© Copyright 2013 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license
and may be used, copied, or disclosed only in accordance with the terms of such
license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
http://www.abb.com/substationautomation

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure and/
or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby
requested to ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standards EN 50263 and EN 60255-26 for the EMC
directive, and with the product standards EN 60255-1 and EN 60255-27 for the low
voltage directive. The product is designed in accordance with the international
standards of the IEC 60255 series.

Table of contents
Section 1 Introduction.......................................................................7
This manual........................................................................................7
Intended audience..............................................................................7
Product documentation.......................................................................7
Product documentation set............................................................7
Document revision history.............................................................8
Related documentation..................................................................8
Symbols and conventions...................................................................8
Symbols.........................................................................................8
Document conventions..................................................................9
Functions, codes and symbols....................................................10
Section 2 IEC 60870-5-103 data mappings...................................15
Overview...........................................................................................15
Supported functions..........................................................................15
Indications and controls....................................................................18
General Data(FUN=0) IEC 60870-5-103 standard......................18
General Data(FUN=10) - 620-specific.........................................19
LD0.MVGAPC1 Multipurpose binary inputs (1)...........................19
LD0.MVGAPC2 Multipurpose binary inputs (2)...........................20
LD0.MVGAPC3 Multipurpose binary inputs (3)...........................20
LD0.MVGAPC4 Multipurpose binary inputs (4)...........................21
LD0.SRGAPC1 Multipurpose binary outputs - flip-flop
resets (1).....................................................................................21
LD0.SRGAPC2 Multipurpose binary outputs - flip-flop
resets (2).....................................................................................21
LD0.SPCGGIO1 Multipurpose binary outputs (1)........................22
LD0.SPCGGIO2 Multipurpose binary outputs (2)........................22
LD0.SPCGGIO3 Multipurpose binary outputs (3)........................23
LD0.SPCRGGIO1 Multipurpose remote binary outputs (1).........24
LD0.SEQRFUF1 Fuse failure protection.....................................24
CTRL.CCRDIF1 Current circuit failure protection........................25
LD0.FRPFRQ1 Frequency protection (1)....................................25
LD0.FRPFRQ2 Frequency protection (2)....................................25
LD0.FRPFRQ3 Frequency protection (3)....................................26
LD0.FRPFRQ4 Frequency protection (4)....................................26
LD0.FRPFRQ5 Frequency protection (5)....................................26
LD0.FRPFRQ6 Frequency protection (6)....................................27
LD0.MAPGAPC1 Multipurpose analog protection function
(1)................................................................................................27
Table of contents
REM620 1
Point List Manual

LD0.MAPGAPC2 Multipurpose analog protection function
(2)................................................................................................27
LD0.MAPGAPC3 Multipurpose analog protection function
(3)................................................................................................27
LD0.MAPGAPC4 Multipurpose analog protection function
(4)................................................................................................28
LD0.MAPGAPC5 Multipurpose analog protection function
(5)................................................................................................28
LD0.MAPGAPC6 Multipurpose analog protection function
(6)................................................................................................28
LD0.MAPGAPC7 Multipurpose analog protection function
(7)................................................................................................28
LD0.MAPGAPC8 Multipurpose analog protection function
(8)................................................................................................29
LD0.MAPGAPC9 Multipurpose analog protection function
(9)................................................................................................29
LD0.MAPGAPC10 Multipurpose analog protection function
(10)..............................................................................................29
LD0.MAPGAPC11 Multipurpose analog protection function
(11)..............................................................................................29
LD0.MAPGAPC12 Multipurpose analog protection function
(12)..............................................................................................30
LD0.XRGGIO105 Alarm and warning..........................................30
LD0.XRGGIO110 Alarm and warning..........................................30
LD0.PSPTUV1 Positive-sequence undervoltage protection
- stage 1.......................................................................................30
LD0.PSPTUV2 Positive-sequence undervoltage protection
- stage 2.......................................................................................31
LD0.DPHHPDOC1 Three-phase directional overcurrent
protection - high stage (1)............................................................31
LD0.DPHHPDOC2 Three-phase directional overcurrent
protection - high stage (2)............................................................31
LD0.DPHLPDOC1 Three-phase directional overcurrent
protection - low stage (1).............................................................32
LD0.PHPTOV3 Phase overvoltage protection - stage 3..............32
LD0.PHPTOV2 Phase overvoltage protection - stage 2..............32
LD0.PHPTOV1 Phase overvoltage protection - stage 1..............33
LD0.PHPTUV3 Phase undervoltage protection - stage 3............33
LD0.PHPTUV2 Phase undervoltage protection - stage 2............33
LD0.PHPTUV1 Phase undervoltage protection - stage 1............34
LD0.NSPTOV1 Negative-sequence overvoltage protection
- stage 1.......................................................................................34
LD0.NSPTOV2 Negative-sequence overvoltage protection
- stage 2.......................................................................................34
LD0.ROVPTOV1 Residual overvoltage protection - stage 1.......34
LD0.ROVPTOV2 Residual overvoltage protection - stage 2.......35
Table of contents
2REM620
Point List Manual

LD0.ROVPTOV3 Residual overvoltage protection - stage 3.......35
LD0.XBGGIO105 Physical binary I/O signal (status only)...........35
LD0.XHBGGIO105 Physical binary I/O signal (status only)........36
LD0.XGGIO100 Physical binary I/O signals (status only)...........36
LD0.XAGGIO130 Physical binary I/O signals (status only).........36
LD0.XBGGIO115 Physical binary I/O signals (status only).........37
LD0.MDSOPT1 Generic operation time supervision...................37
LD0.MDSOPT2 Generic operation time supervision...................37
LD0.MNSPTOC1 Negative-sequence overcurrent
protection for motors (1)..............................................................38
LD0.MNSPTOC2 Negative-sequence overcurrent
protection for motors (2)..............................................................38
LD0.JAMPTOC1 Stalled motor protection ..................................38
LD0.STTPMSU1 Motor startup supervision (1)...........................38
LD0.PREVPTOC1 Phase reversal protection.............................38
LD0.MPDIF1 Motor differential protection (1)..............................39
LD0.MPTTR1 Motor thermal overload protection........................39
LD0.EMSGAPC1 Emergency start .............................................39
LD0.LOFLPTUC1 Loss of load protection...................................39
LD0.LOFLPTUC2 Loss of load protection...................................39
LD0.ARCSARC1 Fault arc protection - stage 1...........................40
LD0.ARCSARC2 Fault arc protection - stage 2...........................40
LD0.ARCSARC3 Fault arc protection - stage 3...........................40
LD0.EFLPTOC1 Non-directional earth-fault and sensitive
earth-fault protection - low stage 1..............................................40
LD0.EFHPTOC1 Non-directional earth-fault and sensitive
earth-fault protection - high stage 1.............................................41
LD0.EFIPTOC1 Non-directional earth-fault and sensitive
earth-fault protection - instantaneous stage 1.............................41
LD0.PHIPTOC1 Phase overcurrent protection -
instantaneous stage 1 ................................................................41
LD0.PHLPTOC1 Phase overcurrent protection - low stage
1...................................................................................................41
LD0.DEFHPDEF1 Directional earth-fault protection - high
stage 1.........................................................................................42
LD0.DEFLPDEF1 Directional earth-fault protection - low
stage 1.........................................................................................42
LD0.CMMXU1 Phase currents (1) limit supervision....................42
LD0.RESCMMXU1 Residual current (1) limit supervision...........42
LD0.VMMXU1 Phase voltage (1) limit supervision......................43
LD0.RESVMMXU1 Residual voltage (1) limit supervision...........43
LD0.CMMXU2 Phase currents (2) limit supervision....................43
CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure
protection.....................................................................................43
Table of contents
REM620 3
Point List Manual

CTRL.Cxxxxx2 Circuit breaker (2) CB object and failure
protection.....................................................................................44
LD0.SSCBR1 Circuit breaker (1) condition monitoring................44
LD0.SSCBR2 Circuit breaker (2) condition monitoring................45
CTRL.DCXSWI1 Disconnector (1) - controllable object..............45
CTRL.DCXSWI2 Disconnector (2) - controllable object..............46
CTRL.DCXSWI3 Disconnector (3) - controllable object..............46
CTRL.DCXSWI4 Disconnector (4) - controllable object..............47
CTRL.ESXSWI1 Earth switch - controllable object.....................47
CTRL.ESXSWI2 Earth switch - controllable object.....................47
CTRL.DCSXSWI1 Disconnector (1) - non-controllable
object...........................................................................................48
CTRL.DCSXSWI2 Disconnector (2) - non-controllable
object...........................................................................................48
CTRL.DCSXSWI3 Disconnector (3) - non-controllable
object...........................................................................................48
CTRL.DCSXSWI4 Disconnector (4) - non-controllable
object...........................................................................................48
CTRL.ESSXSWI1 Earth switch (1) - non-controllable
object...........................................................................................48
CTRL.ESSXSWI2 Earth switch (2) - non-controllable
object...........................................................................................49
LD0.LEDGGIO1 LHMI LED indications Type 1 (2 states)...........49
LD0.LEDGGIO1 LHMI LED indications Type 2 (3 states.
1:1 LED state)..............................................................................49
LD0.FKEYGGIO1 LHMI LED indications.....................................50
LD0.SECRSYN1 Synchrocheck indications ...............................50
Class 2 data measurands.................................................................51
Class 2 private measurand data (6 and 7)..................................52
Section 3 Interoperability profile for 620 series IEC
60870-5-103...................................................................55
Physical layer...................................................................................55
Electrical interface.......................................................................55
Optical interface...........................................................................55
Transmission speed....................................................................55
Link layer..........................................................................................55
Application layer...............................................................................56
Transmission mode for application data......................................56
COMMON ADDRESS of ASDU..................................................56
Selection of standard information numbers in monitor
direction.......................................................................................56
System functions in monitor directions...................................56
Status indications in monitor direction....................................56
Supervision indications in monitor direction...........................57
Table of contents
4REM620
Point List Manual