ABB ABILITY SSC600 User manual

—
ABB ABILITY™ SMART SUBSTATION CONTROL AND PROTECTION FOR ELECTRICAL SYSTEMS
SSC600
Operation Manual

Document ID: 1MRS758850
Issued: 2022-12-05
Revision: D
Product version: 1.0 FP4
© Copyright 2022 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written permission from
ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized
purpose.
The software or hardware described in this document is furnished under a license and may be used,
copied, or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective holders.
SSC600 is an approved Intel® IoT Market Ready Solution.
Open Source Software
This product contains open source software. For license information refer to product documentation at
www.abb.com .
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
www.abb.com/mediumvoltage

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons responsible
for applying the equipment addressed in this manual must satisfy themselves that each intended
application is suitable and acceptable, including that any applicable safety or other operational
requirements are complied with. In particular, any risks in applications where a system failure and/or
product failure would create a risk for harm to property or persons (including but not limited to
personal injuries or death) shall be the sole responsibility of the person or entity applying the
equipment, and those so responsible are hereby requested to ensure that all measures are taken to
exclude or mitigate such risks.
This product has been designed to be connected and communicate data and information via a network
interface which should be connected to a secure network. It is the sole responsibility of the person
or entity responsible for network administration to ensure a secure connection to the network and
to take the necessary measures (such as, but not limited to, installation of firewalls, application of
authentication measures, encryption of data, installation of antivirus programs, etc.) to protect the
product and the network, its system and interface included, against any kind of security breaches,
unauthorized access, interference, intrusion, leakage and/or theft of data or information. ABB is not
liable for any such damages and/or losses.
This document has been carefully checked by ABB but deviations cannot be completely ruled out. In
case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than
under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or
damage resulting from the use of this manual or the application of the equipment.
In case of discrepancies between the English and any other language version, the wording of the
English version shall prevail.

Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility (EMC
Directive 2014/30/EU) and concerning electrical equipment for use within specified voltage limits (Low
Voltage Directive 2014/35/EU). This conformity is the result of tests conducted by ABB in accordance
with the product standard EN 60255-26 for the EMC directive, and with the product standards EN
60255-1 and EN 60255-27 for the low voltage directive. The product is designed in accordance with the
international standards of the IEC 60255 series and IEC 61805-3:2013.

Contents
1 Introduction............................................................................................... 9
1.1 Communication....................................................................................................................................... 9
1.1.1 Ethernet redundancy..............................................................................................................9
1.1.2 Process bus............................................................................................................................. 11
1.2 PCM600 tool............................................................................................................................................11
1.2.1 Connectivity packages......................................................................................................... 12
1.2.2 PCM600 and IED connectivity package version.............................................................. 12
1.3 This manual.............................................................................................................................................12
1.3.1 Intended audience.................................................................................................................12
1.4 Document revision history.................................................................................................................. 18
1.5 Related documentation........................................................................................................................19
1.6 Product documentation set................................................................................................................ 19
2 Safety information..................................................................................20
3 Commissioning........................................................................................ 21
3.1 Commissioning checklist..................................................................................................................... 21
3.2 Checking the installation......................................................................................................................21
3.2.1 Checking of the power supply.............................................................................................21
3.3 Authorizations........................................................................................................................................21
3.3.1 User authorization................................................................................................................ 22
3.4 Setting IED and communication.........................................................................................................23
3.4.1 Setting the communication between IEDs and PCM600.............................................. 23
3.4.2 Communication settings..................................................................................................... 23
3.5 Testing the IED operation....................................................................................................................24
3.5.1 Selecting the IED test mode............................................................................................... 24
3.5.2 Testing functions.................................................................................................................. 25
3.5.3 Selecting the internal fault test..........................................................................................25
3.5.4 Selecting the IED blocked or IED test and blocked mode.............................................26
3.6 ABB Product Data Registration...........................................................................................................27
4 IED operation........................................................................................... 28
4.1 Web HMI.................................................................................................................................................. 28
4.1.1 Authorization......................................................................................................................... 28
4.1.2 Using the Web HMI................................................................................................................29
4.1.3 Identifying the device...........................................................................................................32
4.1.4 Showing parameters............................................................................................................ 32
4.1.5 Editing values.........................................................................................................................33
Contents
SSC600
Operation Manual
7

4.1.6 Committing settings............................................................................................................ 35
4.1.7 Clearing and acknowledging.............................................................................................. 36
4.1.8 Web HMI views....................................................................................................................... 37
4.2 Disturbance identification...................................................................................................................47
4.3 IED parametrization............................................................................................................................. 48
4.3.1 Settings for IED functionality.............................................................................................48
4.3.2 Settings for different operating conditions....................................................................48
4.3.3 Activating programmable virtual LEDs............................................................................ 49
4.4 Monitoring..............................................................................................................................................50
4.4.1 Indications..............................................................................................................................50
4.4.2 Recorded data....................................................................................................................... 50
4.4.3 Monitoring fault records......................................................................................................52
4.4.4 Monitoring events................................................................................................................. 52
4.4.5 Remote monitoring...............................................................................................................52
4.5 Controlling.............................................................................................................................................. 53
4.5.1 Controlling with single-line diagram.................................................................................53
5 Troubleshooting......................................................................................60
5.1 Identifying hardware errors................................................................................................................60
5.2 Identifying runtime errors...................................................................................................................60
5.3 Identifying communication errors.................................................................................................... 60
5.3.1 Internal faults.........................................................................................................................60
5.3.2 Warnings..................................................................................................................................61
5.4 Correction procedures......................................................................................................................... 63
5.4.1 Rebooting the software.......................................................................................................63
5.4.2 Restoring factory settings.................................................................................................. 63
5.4.3 Setting passwords................................................................................................................64
5.4.4 Identifying IED application problems............................................................................... 64
6 Environmental aspects...........................................................................66
6.1 Sustainable development....................................................................................................................66
6.2 Disposal of an IED................................................................................................................................. 66
7 Glossary.................................................................................................... 67
Contents
8 SSC600
Operation Manual

1 Introduction
ABB Ability™ Smart Substation Control and Protection for electrical systems
SSC600 is a Smart Substation device designed for protection, control,
measurement and supervision of utility substations and industrial switchgear and
equipment. The design of the device has been guided by the IEC 61850 standard
for communication and interoperability of substation automation devices. It is
fully integrable with Relion series IEDs for creating a complete solution. Optional
functionality is available at the time of order for both software and hardware, for
example, special application packages and additional communication modules.
Figure 1: SSC600
1.1 Communication
The IED supports the IEC 61850 standard and its specified GOOSE, MMS
and SAV/SMV communication profiles. Operational information and controls are
available through these protocols.
The IEC 61850 communication implementation supports all monitoring and control
functions. Additionally, parameter settings, disturbance recordings and fault
records can be accessed using the IEC 61850 protocol. Disturbance recordings
are available to any Ethernet-based application in the IEC 60255-24 standard
COMTRADE file format. The IED can receive binary signals from other devices (so-
called horizontal communication) using the IEC 61850-8-1 GOOSE profile, where the
highest performance class with a total transmission time of 3 ms is supported.
Furthermore, the IED supports receiving of analog values using GOOSE messaging.
The IED meets the GOOSE performance requirements for class P1 (10 ms) tripping
applications in distribution substations, as defined by the IEC 61850 standard.
The IED can support five simultaneous clients for IEC 61850 MMS reporting. The IED
supports receiving sampled analogue measurements according to IEC 61850-9-2LE
from up to 30 Merging Units or other IEDs.
1MRS758850 D Introduction
SSC600
Operation Manual
9

1.1.1 Ethernet redundancy
IEC 61850 specifies a network redundancy scheme that improves the system
availability for substation communication. It is based on parallel redundancy
protocol PRP-1 defined in the IEC 62439-3:2012 standard. The protocol relies on
the duplication of all transmitted information via two Ethernet ports for one logical
network connection. Therefore, it is able to overcome the failure of a link or switch
with a zero-switchover time, thus fulfilling the stringent real-time requirements for
the substation automation horizontal communication and time synchronization.
PRP specifies that each device is connected in parallel to two local area networks.
Thus, each device incorporates a switch element that forwards frames from port to
port.
IEC 62439-3:2012 cancels and replaces the first edition published in 2010.
These standard versions are also referred to as IEC 62439-3 Edition 1 and
IEC 62439-3 Edition 2. The IED supports IEC 62439-3:2012 and it is not
compatible with IEC 62439-3:2010.
PRP
Each PRP node, called a doubly attached node with PRP (DAN), is attached to
two independent LANs operated in parallel. These parallel networks in PRP are
called LAN A and LAN B. The networks are completely separated to ensure failure
independence, and they can have different topologies. Both networks operate in
parallel, thus providing zero-time recovery and continuous checking of redundancy
to avoid communication failures. Non-PRP nodes, called single attached nodes
(SANs), are either attached to one network only (and can therefore communicate
only with DANs and SANs attached to the same network), or are attached through a
redundancy box, a device that behaves like a DAN.
Figure 2: PRP solution
Introduction 1MRS758850 D
10 SSC600
Operation Manual

In case a laptop or a PC workstation is connected as a non-PRP node to one of
the PRP networks, LAN A or LAN B, it is recommended to use a redundancy box
device or an Ethernet switch with similar functionality between the PRP network
and SAN to remove additional PRP information from the Ethernet frames. In some
cases, default PC workstation adapters are not able to handle the maximum-length
Ethernet frames with the PRP trailer.
There are different alternative ways to connect a laptop or a workstation as SAN to a
PRP network.
• Via an external redundancy box (RedBox) or a switch capable of connecting to
PRP and normal networks
• By connecting the node directly to LAN A or LAN B as SAN
1.1.2 Process bus
Process bus IEC 61850-9-2 defines the transmission of Sampled Measured Values
within the substation automation system. UCA users' group created a guideline
IEC 61850-9-2 LE that defines an application profile of IEC 61850-9-2 to facilitate
implementation and enable interoperability. Process bus is used for distributing
process data from the primary circuit to all process bus compatible IEDs in the
local network in a real-time manner. The data can then be processed by any IED to
perform different protection, automation and control functions.
Transmitting measurement samples over process bus brings also higher error
detection because the signal transmission is automatically supervised. Additional
contribution to the higher availability is the possibility to use redundant Ethernet
network for transmitting SMV signals.
The SSC600 supports receiving of sampled values of analog currents and voltages.
The measured values need to be transferred as sampled values using the IEC
61850-9-2 LE protocol.
The SSC600 IEDs with process bus based applications use IEEE 1588 v2 Precision
Time Protocol (PTP) according to IEEE C37.238-2011 Power Profile for high accuracy
time synchronization. With IEEE 1588 v2, the cabling infrastructure requirement is
reduced by allowing time synchronization information to be transported over the
same Ethernet network as the data communications.
When using PTP in redundant mode, synchronization master is primarily
searched from LAN A. Synchronization master from LAN B is used only, if
no master in LAN A is detected.
1.2 PCM600 tool
Protection and Control IED Manager PCM600 offers all the necessary functionality
to work throughout all stages of the IED life cycle.
• Planning
• Engineering
• Commissioning
• Operation and disturbance handling
• Functional analysis
1MRS758850 D Introduction
SSC600
Operation Manual
11

The whole substation can be controlled and different tasks and functions can be
performed with the individual tool components. PCM600 can operate with many
different topologies, depending on the customer needs.
For more information, refer to PCM600 documentation.
1.2.1 Connectivity packages
A connectivity package is a software component that consists of executable code
and data which enables system tools to communicate with an IED. Connectivity
packages are used to create configuration structures in PCM600. The latest
PCM600 and connectivity packages are backward compatible with older IED
versions.
A connectivity package includes all of the data which is used to describe the IED.
For example, it contains a list of the existing parameters, data format used, units,
setting range, access rights and visibility of the parameter. In addition, it contains
code which allows software packages that consume the connectivity package to
properly communicate with the IED. It also allows for localization of text even when
its read from the IED in a standard format such as COMTRADE.
Update Manager is a tool that helps in defining the right connectivity package
versions for different system products and tools. Update Manager is included with
products that use connectivity packages.
1.2.2 PCM600 and IED connectivity package version
• Protection and Control IED Manager PCM600 2.9 or later
• SSC600 Connectivity Package Ver.1.0 or later
Download connectivity packages from the ABB Web site
www.abb.com/
mediumvoltage or directly with the Update Manager in PCM600.
1.3 This manual
The operation manual contains instructions on how to operate the IED once it has
been commissioned. The manual provides instructions for monitoring, controlling
and setting the IED. The manual also describes how to identify disturbances and
how to view calculated and measured power grid data to determine the cause of a
fault.
1.3.1 Intended audience
This manual addresses the operator, who operates the IED on a daily basis.
The operator must be trained in and have a basic knowledge of how to operate
protection equipment. The manual contains terms and expressions commonly used
to describe this kind of equipment.
Introduction 1MRS758850 D
12 SSC600
Operation Manual

1.3.1.1 Document conventions
A particular convention may not be used in this manual.
• Abbreviations and acronyms in this manual are spelled out in the glossary. The
glossary also contains definitions of important terms.
• whmi menu paths are presented in bold typeface.
Select Main menu> Settings.
• whmi menu names are presented in bold typeface.
Click Information in the whmi menu structure.
• Parameter names are shown in italics .
The function can be enabled and disabled with the Operation setting.
• Parameter values are indicated with quotation marks.
The corresponding parameter values are "On" and "Off".
• ied input/output messages and monitored data names are shown in Courier
font.
When the function starts, the START output is set to TRUE.
1.3.1.2 Symbols
The warning icon indicates the presence of a hazard which could result in
electrical shock or other personal injury.
The caution icon indicates important information or warning related to
the concept discussed in the text. It might indicate the presence of
a hazard which could result in corruption of software or damage to
equipment or property.
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project
or how to use a certain function.
Although the warning hazards are related to personal injury, it is necessary
to understand that under certain operational conditions, operation of damaged
equipment may result in degraded process performance leading to personal injury
or death. Therefore, comply fully with all warning and caution notices.
1.3.1.3 Functions, codes and symbols
All available functions included in the IED are listed in the tables below. Available
functions depend on the chosen product options.
1MRS758850 D Introduction
SSC600
Operation Manual
13

Table 1: Protection functions
Function IEC 61850 IEC 60617 ANSI
Logical
device Logical nodes
Three-phase non-directional
overcurrent protection, low
stage
PHLPTOC 3I> 51P-1 LD0 PHLPTOC
Three-phase non-directional
overcurrent protection, high
stage
PHHPTOC 3I>> 51P-2 LD0 PHHPTOC
Three-phase non-directional
overcurrent protection, instan-
taneous stage
PHIPTOC 3I>>> 50P LD0 PHIPTOC
Three-phase directional over-
current protection, low stage
DPHLPDOC 3I> -> 67P/51P-1 LD0 DPHLPTOC DPHLRDIR
Three-phase directional over-
current protection, high stage
DPHHPDOC 3I>> -> 67P/51P-2 LD0 DPHHPTOC DPHHRDIR
Non-directional earth-fault
protection, low stage
EFLPTOC Io> 51G/51N-1 LD0 EFLPTOC
Non-directional earth-fault
protection, high stage
EFHPTOC Io>> 51G/51N-2 LD0 EFHPTOC
Non-directional earth-fault
protection, instantaneous
stage
EFIPTOC Io>>> 50G/50N LD0 EFIPTOC
Directional earth-fault protec-
tion, low stage
DEFLPDEF Io> -> 67G/N-1 51G/N-1 LD0 DEFLPTOC DEFLRDIR
Directional earth-fault protec-
tion, high stage
DEFHPDEF lo>> -> 67G/N-1 51G/N-2 LD0 DEFHPTOC DEFHRDIR
Admittance-based earth-fault
protection
EFPADM Yo> -> 21YN LD0 EFPADM
Wattmetric-based earth-fault
protection
WPWDE Po> -> 32N LD0 WRDIR WPSDE
WMMXU
Transient/intermittent earth-
fault protection
INTRPTEF lo> -> IEF 67NTEF/NIEF LD0 INTRPTEF
Non-directional (cross-coun-
try) earth-fault protection, us-
ing calculated Io
EFHPTOC Io>> 51G/51N-2 LD0 EFHPTOC
Negative-sequence overcurrent
protection
NSPTOC I2> 46M LD0 NSPTOC
Phase discontinuity protection PDNSPTOC I2/I1> 46PD LD0 PDNSPTOC
Residual overvoltage protec-
tion
ROVPTOV Uo> 59G/59N LD0 ROVPTOV
Three-phase undervoltage pro-
tection
PHPTUV 3U< 27 LD0 PHPTUV
Three-phase overvoltage pro-
tection
PHPTOV 3U> 59 LD0 PHPTOV
Positive-sequence undervolt-
age protection
PSPTUV U1< 27PS LD0 PSPTUV
Negative-sequence overvolt-
age protection
NSPTOV U2> 59NS LD0 NSPTOV
Frequency protection FRPFRQ f>/f<,df/dt 81 LD0 FRPTRC FRPTOF
FRPTUF FRPFRC
Distance protection DSTPDIS Z< 21P, 21N LD0 GFCPDIS
GFCRDIR
DST1PDIS
DST2PDIS
DST3PDIS
DST4PDIS
DST5PDIS
DSTRDIR
GFC1RFRC
Table continues on the next page
Introduction 1MRS758850 D
14 SSC600
Operation Manual

Function IEC 61850 IEC 60617 ANSI
Logical
device Logical nodes
GFC2RFRC
GFC3RFRC
Three-phase thermal protec-
tion for feeders, cables and
distribution transformers
T1PTTR 3Ith>F 49F LD0 T1PTTR
Three-phase thermal overload
protection, two time constants
T2PTTR 3Ith>T/G/C 49T/G/C LD0 T2PTTR
Negative-sequence overcurrent
protection for ma- chines
MNSPTOC I2>M 46M LD0 MNSPTOC
Loss of load supervision LOFLPTUC 3I< 37 LD0 LOFLPTUC
Motor load jam protection JAMPTOC Ist> 50TDJAM LD0 JAMPTOC
Motor start-up supervision STTPMSU Is2t n< 49,66,48,50TDLR LD0 STTPMSS STTPMRI
Phase reversal protection PREVPTOC I2>> 46R LD0 PREVPTOC
Thermal overload protection
for motors
MPTTR 3Ith>M 49M LD0 MPTTR
Stabilized and instantaneous
differential protection for two-
winding transformers
TR2PTDF 3dI>T 87T LD0 TR2PTRC
TR2LPDIF
TR2H2PHAR
TR2H5PHAR
TR2HPDIF
Numerically stabilized low-im-
pedance restricted earth-fault
protection
LREFPNDF dIoLo> 87NLI LD0 LREFPDIF LREFPHAR
Circuit breaker failure protec-
tion
CCBRBRF 3I>/Io>BF 50BF LD0 CCBRBRF
Three-phase inrush detector INRPHAR 3I2f> 68HB LD0 INRPHAR
Switch onto fault CBPSOF SOTF SOTF LD0 CBPSOF
Master trip TRPPTRC Master Trip 94/86 LD0 TRPPTRC
Arc protection ARCSARC ARC AFD LD0 ARCSARC ARC1PIOC
ARC2PIOC ARCPTRC
Multipurpose protection MAPGAPC MAP MAP LD0 MAPGAPC
Load-shedding and restoration LSHDPFRQ UFLS/R 81LSH LD0 LSHDPTRC LSHDPTOF
LSHDPTUF LSHDPFRC
Fault locator SCEFRFLO FLOC FLOC LD0 SCEFRFLO SCEFZLIN
SCEF2ZLIN SCEF3ZLIN
FLORFRC
Reverse power/directional
overpower protection
DOPPDPR P>/Q> 32R/32O LD0 DPPDOP DOPMMXU
Three-phase underimpedance
protection
UZPDIS Z>G 21G LD0 UZPDIS UZMMXU
Multifrequency admittance-
based earth-fault protection
MFADPSDE Io> ->Y 67NYH LD0 MFADPSDE MFADRDIR
Busbar differential protection BBPBDF 3Id/I 87BL LD0 BBPTRC
ZNAPDIF
ZNBPDIF
ZNCZPDIF
SFAPDIF
SFBPDIF
BBCCSPVC
Busbar zone selection ZNRSRC ZNRSRC ZNRSRC LD0 ZNRSRC
Load blinder LBRDOB LB 21LB LD0 LBRDOB
LBMMXU
Table continues on the next page
1MRS758850 D Introduction
SSC600
Operation Manual
15

Function IEC 61850 IEC 60617 ANSI
Logical
device Logical nodes
Three-phase overload protec-
tion for shunt capacitor banks
COLPTOC 3I> 3I< 51,37,86C LD0 COL1PTOC
COLPTUC
COL2PTOC
Current unbalance protection
for shunt capacitor banks
CUBPTOC dI>C 60N LD0 CUB1PTOC
CUB2PTOC
Three-phase current unbalance
protection for shunt capacitor
banks
HCUBPTOC 3dI>C 60P LD0 HCUB1PTOC
HCUB2PTOC
Shunt capacitor bank switch-
ing resonance protection,cur-
rent based
SRCPTOC TD> 55ITHD LD0 SRC1PTOC
SRC2PTOC
Anomaly detector ANOGAPC ANOGAPC ANOGAPC LD0 ANOGAPC
Table 2: Interconnection functions
Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Directional reactive power
undervoltage protection
DQPTUV Q> ->,3U< 32Q,27 LD0 DQPTUV
DQPDOP
DQMMXU
Low-voltage ride-through
protection
LVRTPTUV U<RT 27RT LD0 LVRTPTUV
Table 3: Power quality functions
Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Current total de-
mand distortion
CMHAI PQM3I PQM3I CMHAI CMHAI
Voltage total har-
monic distortion
VMHAI PQM3U PQM3V VMHAI VMHAIVMHAI
Voltage variation PHQVVR PQMU PQMV PHQVVR
PH2QVVR
PH3QVVR
QVVRQRC
QVV2RQRC
QVV3RQRC
PHQVVR
PH2QVVR
PH3QVVR
QVVMSTA
QVV2MSTA
QVV3MSTA
Voltage unbalance VSQVUB PQUUB PQVUB - -
Table 4: Control functions
Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Circuit-breaker con-
trol
CBXCBR I <-> O CB I <-> O CB CTRL CBCSWI
CBCILO
CBXCBR
Disconnector con-
trol
DCXSWI I <-> O DCC I <-> O DCC CTRL DCCSWI
DCCILO
DCXSWI
Earthing switch
control
ESXSWI I <-> O ESC I <-> O ESC CTRL ESCSWI
ESCILO
ESXSWI
Table continues on the next page
Introduction 1MRS758850 D
16 SSC600
Operation Manual

Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Disconnector posi-
tion indication
DCSXSWI I <-> O DC I <-> O DC CTRL DCSXSWI
Earthing switch in-
dication
ESSXSWI I <-> O ES I <-> O ES CTRL ESSXSWI
Emergency start-
up
ESMGAPC ESTART ESTART LD0 ESMGAPC
Autoreclosing DARREC O -> I 79 LD0 DARREC
Tap changer posi-
tion indication
TPOSYLTC TPOSM 84M LD0 TPOSYLTC
Tap changer con-
trol with voltage
regulator
OLATCC COLTC 90V LD0 OLATCC
Synchronism and
energizing check
SECRSYN SYNC 25 LD0 SECRSYN
Table 5: Condition monitoring and supervision functions
Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Circuit-breaker con-
dition monitoring
SSCBR CBCM CBCM LD0 SSCBR1
SPH1SCBR
SPH2SCBR
SPH3SCBR
SSOPM
SSIMG
Runtime counter
for machines and
devices
MDSOPT OPTS OPTM LD0 MDSOPT
Fuse failure super-
vision
SEQSPVC FUSEF VCM, 60 LD0 SEQSPVC
Table 6: Measurement functions
Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
Disturbance re-
corder
RDRE DR DFR LD0 DR_LLN0
DR_LPHD
RDRE
RBDR
Fault record FLTRFRC FAULTREC FAULTREC LD0 FLTRFRC
Three-phase cur-
rent measurement
CMMXU 3I 3I LD0 CMMXU
CAVMMXU
CMAMMXU
CMIMMXU
Sequence current
measurement
CSMSQI I1, I2, I0 I1, I2, I0 LD0 CSMSQI
Residual current
measurement
RESCMMXU Io In LD0 RESCMMXU
RCAVMMXU
RCMAMMXU
RCMIMMXU
Three-phase volt-
age measurement
VMMXU 3U 3V LD0 VMMXU
VAVMMXU
Residual voltage
measurement
RESVMMXU Uo Vn LD0 RESVMMXU
RVAVMMXU
RVMAMMXU
Table continues on the next page
1MRS758850 D Introduction
SSC600
Operation Manual
17

Function IEC 61850 IEC 60617 ANSI Logical device Logical nodes
RVMIMMXU
Sequence voltage
measurement
VSMSQI U1, U2, U0 V1, V2, V0 LD0 VSMSQI
Three-phase power
and energy meas-
urement
PEMMXU P, E P, E LD0 PEMMXU
PEMMTR
PEAVMMXU
PEMAMMXU
PEMIMMXU
Frequency meas-
urement
FMMXU f f LD0 FMMXU
IEC 61850-9-2 LE
sampled value re-
ceiving
SMVRECEIVE SMVRECEIVE SMVRECEIVE SVIL1TCTR
SVIL2TCTR
SVIL3TCTR
SVRESTCTR
SVUL1TVTR
SVUL2TVTR
SVUL3TVTR
SVRESTVTR
Table 7: Other functions
Function IEC 61850 IEC 60617 ANSI
Logical
device Logical nodes
Minimum pulse timer TPGAPC TP TP TPGAPC
Minimum pulse timer (second
resolution)
TPSGAPC TPS TPS TPSGAPC
Minimum pulse timer minute
resolution)
TPMGAPC TPM TPM TPMGAPC
Pulse timer PTGAPC PT PT PTGAPC
Time delay off TOFGAPC TOF TOF TOFGAPC
Time delay on TONGAPC TON TON TONGAPC
Set-reset SRGAPC SR SR SRGAPC
Move MVGAPC MV MV MVGAPC
Generic control point SPCGAPC SPC SPC SPCGAPC
Analog value scaling SCA4GAPC SCA4 SCA4 SCA4GAPC
Integer value move MVI4GAPC MVI4 MVI4 MVI4GAPC
Voltage switch VMSWI VSWI VSWI VMSWI
Current switch CMSWI CMSWI CMSWI CMSWI
Current sum CMSUM CSUM CSUM SIL1TCTR
SIL2TCTR
SIL3TCTR
SRESTCTR
Introduction 1MRS758850 D
18 SSC600
Operation Manual

1.4 Document revision history
Document revision/
date
Product series
version History
A/2019-05-10 1.0 First release
B/2020-03-23 1.0 FP1 Content updated
C/2021-11-26 1.0 FP3 Content updated
D/2022-12-05 1.0 FP4 Content updated
Download the latest documents from the ABB Web site www.abb.com/
mediumvoltage .
1.5 Related documentation
Product series- and product-specific manuals can be downloaded from the ABB Web
site www.abb.com/mediumvoltage .
1.6 Product documentation set
Planning & purchase Engineering Installation Commissioning Operation Maintenance Decommissioning, deinstallation & disposal
Brochure
Product guide
Operation manual
Connection diagram
Engineering manual
Technical manual
Application manual
Cyber security deployment guideline
Communication protocol manual
Figure 3: The intended use of documents during the product life cycle
Product series- and product-specific manuals can be downloaded from
the ABB Web site.
1MRS758850 D Introduction
SSC600
Operation Manual
19

2 Safety information
Dangerous voltages can occur on the connectors, even though the
auxiliary voltage has been disconnected.
Non-observance can result in death, personal injury or substantial
property damage.
Only a competent electrician is allowed to carry out the electrical
installation.
National and local electrical safety regulations must always be followed.
The frame of the device has to be carefully earthed.
The device contains components which are sensitive to electrostatic
discharge. Unnecessary touching of electronic components must
therefore be avoided.
Whenever changes are made in the device, measures should be taken to
avoid inadvertent tripping.
Safety information 1MRS758850 D
20 SSC600
Operation Manual