ABB Contrac PME120AI Original operating manual

—
ABB MEASUREMENT & AN
ALYTICS | SERVICE INSTRUCTION | SEI/PME120-EN REV. A
PME120
-AI / PME120-AN (Contrac)
Electrical rotary actuator
—
ABB Measurement & Analytics
For your local
ABB contact, visit:
www.abb.com/contacts
For more product information, visit:
www.abb.com/actuators
Electrical rotary actuator
for the
operation of final control elements.
SEI/PME120
-EN Rev. A 04.2020
—
PME120
-AI
PME120
-AN
Introduction
Compact actuator for the operation of final
control elements with preferably 90° rotary
movement such as valve flaps, ball valves,
etc.
The nominal torque is transferred through a lever
actuator. A special electronic unit controls the
actuator. The special electronic unit serves as the
interface be
tween actuator and control system.
Additional Information
Additional documentation on
PME120-AI / PME120-
AN (Contrac)
is available for download free of charge
at www.abb.com/actuators.
Alternatively simply scan this code:
—
We reserve the right to make technical changes or modify the contents of this document
without prior noti
ce. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject
matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents
– in whole
or in parts
– is forbidden without prior written consent of ABB.
© ABB 2020 3KXE111018R4301

2 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
Table of contents
1Safety.......................................................................... 3
General information and instructions.................................. 3
Warnings.................................................................................... 3
Intended use .............................................................................4
Improper use.............................................................................4
Notes on data safety ...............................................................4
Warranty provisions.................................................................4
Manufacturer’s address ..........................................................4
2Introduction ...............................................................5
Safety and precautions ...........................................................5
Tools ...........................................................................................5
3Actuator versions ......................................................6
PME120-AI..................................................................................6
PME120-AN ................................................................................6
4Lubrication .................................................................6
Mounting position ...................................................................6
Oil change.................................................................................. 7
PME oil types............................................................................. 7
5Maintenance...............................................................8
Safety instructions...................................................................8
General .......................................................................................8
Lever ...........................................................................................8
Lever removal.......................................................................8
Lever installation .................................................................9
Ball-and-socket-joint ...............................................................9
Removal.................................................................................9
Installation............................................................................9
Sealing ring of output drive shaft .......................................10
Motor........................................................................................ 12
Motor removal.................................................................... 12
Motor shaft sealing ring .................................................. 12
Motor installation.............................................................. 13
Brake adjustment................................................................... 13
6Electrical connections............................................. 14
General .....................................................................................14
Actuator versions...................................................................14
PME120-AI ...........................................................................14
PME120-AN .........................................................................14
Removal of integrated electronic unit................................ 15
Covers....................................................................................... 15
Integrated PME120-AI Electronic unit.................................16
Analog / Digital.................................................................. 16
PROFIBUS DP®.................................................................... 17
Electronic unit EAN823 (Contrac) for PME120-AN............ 18
Analog / Digital.................................................................. 18
PROFIBUS DP®....................................................................19
Electronic unit EAS822 (Contrac) for PME120-AN ............20
Analog / Digital..................................................................20
Fuses ........................................................................................ 21
Fuse location......................................................................22
7Exchange of position sensor ..................................23
Dismounting........................................................................... 23
PME120-AN (for separate electronic unit).................... 23
PME120-AI (with integrated electronic unit)................ 23
Mounting................................................................................. 24
8Electrical test values ...............................................25
Test values (position sensor) .............................................. 25
Test values (Brake and Motor) ............................................ 26
Brake voltage..................................................................... 26
Motor voltage .................................................................... 26
Winding resistance ........................................................... 26
9Failure detection......................................................27
LED signals at commissioning and service field.............. 27
10 Troubleshooting ......................................................27
General..................................................................................... 28
Failures at brake, fuse or wiring ......................................... 29
Operation mode (MAN / AUT).............................................30
Input configuration ................................................................31
Operation behind step controller....................................... 32
Failure Diagram...................................................................... 33
Failure due to response of positioning loop
monitoring .............................................................................. 34
General..................................................................................... 34
User interface menus............................................................ 35

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 3
1Safety
General information and instructions
These instructions are an important part of the product and
must be retained for future reference.
Installation, commissioning, and maintenance of the product
may only be performed by trained specialist personnel who have
been authorized by the plant operator accordingly. The specialist
personnel must have read and understood the manual and must
comply with its instructions.
For additional information or if specific problems occur that are
not discussed in these instructions, contact the manufacturer.
The content of these instructions is neither part of nor an
amendment to any previous or existing agreement, promise or
legal relationship.
Modifications and repairs to the product may only be performed
if expressly permitted by these instructions.
Information and symbols on the product must be observed.
These may not be removed and must be fully legible at all times.
The operating company must strictly observe the applicable
national regulations relating to the installation, function testing,
repair and maintenance of electrical products.
Warnings
The warnings in these instructions are structured as follows:
DANGER
The signal word ‘DANGER’ indicates an imminent danger.
Failure to observe this information will result in death or
severe injury.
WARNING
The signal word ‘WARNING’ indicates an imminent danger.
Failure to observe this information may result in death or
severe injury.
CAUTION
The signal word ‘CAUTION’ indicates an imminent danger.
Failure to observe this information may result in minor or
moderate injury.
NOTICE
The signal word ‘NOTICE’ indicates possible material damage.
Note
‘Note’ indicates useful or important information about the
product.

4 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 1 Safety
Intended use
Control actuators are used exclusively for operating final control
elements (valves, valve flaps, etc.).
They may only be operated using a suited Contrac electronic unit
for field installation or mounting rack installation.
In addition to this operating instruction, the relevant
documentation for the electronic unit and software tool must be
observed.
Improper use
The following are considered to be instances of especially
improper use of the device:
• For use as a climbing aid, for example for mounting
purposes.
• For use as a bracket for external loads, for example as a
support for piping, etc.
• Material application, for example by painting over the
housing, name plate or welding/soldering on parts.
• Material removal, for example by spot drilling the
housing.
Notes on data safety
This product is designed to be connected to and to
communicate information and data via a network interface.
It is operator’s sole responsibility to provide and continuously
ensure a secure connection between the product and your
network or any other network (as the case may be).
Operator shall establish and maintain any appropriate measures
(such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data,
installation of anti-virus programs, etc.) to protect the product,
the network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and / or theft of data or information.
ABB Automation Products GmbH and its affiliates are not liable
for damages and / or losses related to such security breaches,
any unauthorized access, interference, intrusion, leakage and /
or theft of data or information.
Warranty provisions
Using the device in a manner that does not fall within the scope
of its intended use, disregarding this manual, using
underqualified personnel, or making unauthorized alterations
releases the manufacturer from liability for any resulting
damage. This renders the manufacturer's warranty null and void.
Manufacturer’s address
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
Customer service center
Tel: [phone]
Email: automation.servic[email protected].com

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR| SEI/PME120-EN REV. A 5
2Introduction
1
Handwheel crank
2
Plug
3
Lever
4
Ball-and-socket joint
5
Lever cover
6
Adjustable stops
(under the lever cover)
7
Gear housing
8
Control motor
9
Cover (for PME120-AI incl.
electronic unit)
j
Handwheel release
Figure 1: PME120 (illustrations may differ from actual installation)
This service instruction refers to the ABB rotary actuators
PME120-AI (with integrated electronic unit) and PME120-AN (for
separate electronic unit).
It amends and deepens the routine maintenance description in
the standard instruction, which we strongly recommend being
also available for all maintenance work.
Safety and precautions
When mounting the actuator in areas which may be accessed by
unauthorized persons, take the required protective measures.
• The actuators perform movements for positioning vanes and
valves. Handle properly and with care. Otherwise, a hazard of
bruise injuries may arise.
• When changing the oil of the actuator, thoroughly remove
any oil that may have run down on the floor during the
procedure to avoid accidents.
• Dispose of the waste oil in compliance with the respective
local regulations. Make sure that no waste oil reaches the
water cycle.
• Only qualified specialists who have been trained for these
tasks are authorized to mount and adjust the control
actuator, and to make the electrical connection.
• When working on the actuator itself or the electronics always
observe the locally valid accident prevention regulations and
the regulations concerning the construction of technical
installations.
• Use the eye bolt at the actuator to lift or lower it. Only load it
vertically. Do not lift or lower the actuator when it is mounted
on a valve or similar final control element.
• Switch-off the voltage supply; make sure that unintentional
switching on is not possible.
• Make sure that switching off the power supply does not
affect the plant process.
• Make sure that the final control element is not exposed to
process forces.
Tools
NOTICE
Damage to the device due to improper tools!
Using improper tools may damage the actuator or its
components.
• Only use proper tools for maintenance work.
Note
• Maintenance at Contrac actuators requires tools which are
usually available in a workshop. Please consider that all
dimensions are based on the metrical system. This applies
also for the wrench sizes, threads etc.
• Use appropriate sleeves for the installation of the sealing
rings (see Installation on page 13 for details).

6 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
3Actuator versions
Electrical rotary actuators PME120 are available in two versions:
• PME120-AI (with integrated electronic unit)
• PME120-AN (for separate electronic units)
PME120-AI
PME120-AI
Electronic unit
Figure 2: PME120AI with dismounted electronic unit
PME120-AN
PME120
-AN
Electronic unit EAN823
for field installation
Electronic unit
EAS822 for rack
installation
Figure 3: PME120-AN with available, separate electronic units
4Lubrication
Mounting position
The spur gearing of the actuator PME120 and RHD250 /
RHD500 / RHD800 / RHD1250 / RHD2500 / RHD4000 (Contrac)
are lubricated with oil. They contain the max. oil quantity when
leaving the manufacturer. Once the actuator is installed replace
the uppermost check plug by the separately supplied venting
plug.
1
Control screw
2
Vent valve
Figure 4: Permissible mounting positions
The mounting positions presented are permissible. To facilitate
mounting and maintenance, however, it is recommended that
you use position IMB 3.
For each mounting position, you should check the specified oil
level before commissioning, see Filling volumes on page 7.
Note
It is important that sufficient cooling air is supplied, sufficient
space is available for changing components and free access is
guaranteed to the electronic unit cover (PME120-AI).
To achieve this, allow for the following minimum distances:
Actuator
A
PME120
30 mm (1.18 in)
RHD250
40 mm (1.57 in)
RHD500 / RHD800
30 mm (1.18 in)
RHD1250 / RHD2500
40 mm (1.57 in)
RHD4000
40 mm (1.57 in)

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR| SEI/PME120-EN REV. A 7
Oil change
Note
Oils for different temperature ranges may not mixed.
During an oil change, thoroughly remove any oil that may have
escaped to avoid accidents.
Dispose of old oil according to local regulations. Make sure that
the oil does not enter the water cycle. Make sure that any oil
leaking from the device cannot come into contact with hot
components.
Proceed as follows to drain or change the oil:
1. Provide a collecting vessel capable of holding the expected
oil quantity in accordance with Filling volumes on page 7 .
2. Open and release the vent valve, see Mounting position on
page 6.
3. Unscrew the lowermost drain plug to drain the oil.
4. Collect the oil in the collection vessel.
5. Make sure all of the oil has been removed from the actuator
housing.
6. Screw the drain plug back in.
7. Refill with the proper volume of oil in accordance with Filling
volumes on page 7 and securely tighten the vent valve.
PME oil types
Actuator type
Ambient temperature
Oil types -
DIN 51517
Motor bearing (grease)
with heat
without heat
PME120
-AI
(with integrated electronic unit)
−
25 to 55 °C
(−15 to 130 °F)
−
10 to 55 °C
(15 to 130 °F)
Mobil SHC 629 – DIN 51517 / ISO 12925-
1
ESSO Beacon 325
PME120
-AN
(for separate electronic unit)
−
25 to 55 °C
(−15 to 130 °F)
−
10 to 65 °C
(15 to 150 °F)
–
−
1 to 85 °C
(30 to 185 °F)
Mobil SHC 632 – DIN 51517 / ISO 12925-
1
Filling volumes
PME120-AI/-AN
Mounting position
IMB 3
IMB 6
IMB 7
IMB 8
IMV 5
IMV 6
Minimum oil level l
(gal)*
Approx. 2.2 (0.58)
Approx. 2.5 (0.66)
Approx. 2.2 (0.58)
Approx. 2.2 (0.58)
Approx. 2.5 (0.66)
Approx. 2.5 (0.66)
Minimum oil level under inspection
plug mm (in)
45
mm (1.77)
2
mm (0.08)
42 (1.65)
20 (0.79)
23
(0.91)
17 (0.67)
* US liquid gallon

8 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
5Maintenance
Safety instructions
WARNING
Risk of injury due to live parts!
Risk of death or serious injuries due to electricity and
unexpected machine movements. In automatic mode the
motor is always under power, even at standstill.
• When working on the actuator or the related subassembly,
switch off the supply voltage for the electronic unit and
separate anti-condensation heater (option), and take
precautions to prevent unintentional switch-on.
Repair and maintenance activities may only be performed by
authorized customer service personnel.
When replacing or repairing individual components, use original
spare parts.
General
Contrac actuators feature a robust construction. As a result,
they are highly reliable and require minimal maintenance. The
maintenance intervals depend upon the effective load and are
therefore not specified here.
The built-in microprocessor evaluates the actual load factors
(e.g. torques, forces, temperatures, etc.) and derives the
remaining operating time until the next routine maintenance is
required.
Use the configuration program to view this information.
Apart from the load dependent maintenance intervals
determined by the microprocessor we recommend routine
maintenance at least every 10 years.
The following description of the maintenance work provide that
the actuator is disconnected from the damper and that all
electrical supply is disconnected.
Lever
Lever removal
Figure 5: Lever mounted on the shaft
Figure 6: Use of draw-off tool for lever removal
In some case it may be useful to detach the linkage bar from the
ball-and-socket-joint, however, it is not absolutely necessary.
Refer to Figure 5and Figure 6for the removal procedure!
1. Screw-off the nut on the lever clamping bolt 1and put the
bolt aside.
2. Put an appropriate draw-off tool 2onto lever 4and shaft
(see Figure 6for details); make sure that the claws 3are
symmetrically behind the lever and that the bolt tip is on the
shaft center 5.
3. Put a wrench onto the opposite bolt end and turn the bolt;
4. put the lever carefully aside once it is off the shaft.

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 9
Lever installation
NOTICE
Make sure that the shaft surface and the shaft bore in the
ever are clean and free of grease or any other lubricant.
1. Put the appropriate key into the groove in the shaft.
2. Use an expanding screw to spread the lever seat.
3. Push a counterpart (soft metal) into the lever gap in order to
protect the expanding screw thread.
4. Push the lever onto the shaft until it is nearly in the same
position as it was before.
5. Put the lever clamping bolt into the lever and tighten the nut
with a torque of 23 Nm (17 lbf-ft).
Ball-and-socket-joint
Figure 7: Ball-and-socket-joint
Figure 8: Use of draw-off tool
In some case it may be useful to detach the linkage bar from the
ball-and-socket-joint, however, it is not absolutely necessary.
Note
The ball-and-socket joint may be mounted / removed with the
lever mounted on the shaft or with dismounted lever. If the lever
remains mounted on the shaft, move it into a position, where
you get free access from the rear lever side.
Removal
1. Pull the cotter pin 1out of the castle nut 2.
2. Screw-off the castle nut.
3. Put an appropriate draw-off tool 3onto lever 4and joint
bolt 5(see Figure 15 for details); make sure that the
claws 6grip symmetrically behind the lever and that the
bolt tip is on the joint bolt center.
4. Put a wrench onto the opposite bolt end and turn the bolt
clockwise.
5. Press the joint bolt out of the lever.
Installation
1. Push the bolt of the ball-and-socket joint into the lever hole.
2. Put the crown nut onto the bolt and tighten it with the
required torque of 80 Nm (60 lbf-ft).
3. Secure the crown nut with a new cotter pin.

10 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 5 Maintenance
Sealing ring of output drive shaft
A
Drive pinion
B
Output shaft
C
Handwheel mechanism
D
Motor
E
Brake
Figure 9: Sectional view of PME120

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 11
In order to change the O-ring 2and sealing ring 4of the
output drive shaft proceed as follows:
1. Remove lever or coupling from the output shaft.
2. Make sure that the oil level is below the O-ring 1.
3. If necessary, drain the oil (see Mounting position on page 6).
4. Remove the key 2.
5. Loosen and remove the flange screws.
6. Two tap holes (thread size: M6) on the bolt circle for the
flange screws allow to use forcing screws; turn these screws
clockwise to remove the flange 3; the thread length of the
forcing screws should be at least 25 mm.
7. Pull the flange3from the shaft.
8. Turn the forcing screws out.
9. Take the O-ring 1and the sealing ring 2out.
10. Clean the shaft and the flange; slightly grease the sealing
ring.
11. Replace the O-ring and the sealing ring.
12. Cover the key groove in the shaft prior to the flange re-
installation in order to avoid any damage of the new sealing
ring.
13. Push the flange carefully over the shaft and fasten the flange
screws crosswise; tightening torque for the flange screws =
2.8 Nm (2.01 ft-lbs).
14. Remove key cover and re-install key 4, lever or coupling.
1
Flange screws
2
Tap holes
Figure 10: Front view of shaft bearing flange
Note
Make sure that the ‘open’ side of the sealing ring points towards
the oil
1
Sealing ring
2
Flange
3
Sleeve (auxiliary tool)
Figure 11: Flange and sealing ring / Use of auxiliary tool for sealing ring installation
(exemplary picture)

12 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 5 Maintenance
Motor
PME120 uses an integrated motor. The stator is integrated into
the actuator housing which makes the motor housing a part of
the actuator housing.
Motor removal
DANGER
Danger to life due to unexpected movement of the actuator!
Note that the actuator position may be changed accidentally
by the external load on the drive when the brake is released, or
the motor is removed.
NOTICE
Material damage
The lower end of the stator shaft is supported by 2 separated
disk springs. Make sure you get them out
with the motor.
Figure 12: Rear view of PME120 (without cover / electronics)
Figure 13: Brake body with rotor
1. Remove the rear cover (cover with electronics at PME120-AI).
2. Unscrew the 4 motor fastening screws 1.
3. Loosen the 4 grub screws 2.
4. Take the brake body with rotor out 3.
5. Take the stator 4out.
Motor shaft sealing ring
Removal
Figure 14: Removal
The motor shaft sealing ring prevents the oil in the gearbox to
penetrate into the motor housing.
Once the stator is out, use two appropriate hooks 1to pull the
motor sealing ring 2out; see Figure 34.

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 13
Installation
1
Sleeve
2
Sealing ring
3
Flange
4
Oil
5
Squeezer
6
Gearbox
7
Mounting sleeve
Figure 15: Installation
1. Grease the new sealing ring and press it in the flange as
shown in Figure 15.
2. Make sure that the ‘open’ part of the sealing ring points
towards the oil; see Figure 15.
3. Use appropriate squeezer or similar device to press the
sealing ring uniformly into the flange (see right part of
Figure 15).
Motor installation
1. Put the stator into the actuator housing.
2. Make sure, the hose protected cables are within the groove
(see Figure 16 on page 13).
3. Put the rotor with the brake body into the stator housing.
4. Tighten the 4 motor screws.
5. Tighten the 4 grub screws to tense rotor / stator housing.
6. Use appropriate retainer (DELO-ML 5228 or LOCTITE 243;
both medium-firm; detachable) to secure the grub screws.
(Refer to Figure 12 and Figure 13 on page 12 for reference no.)
Brake
Brake adjustment
WARNING
Risk of injury
Note that the actuator position may be changed accidentally
by the external load on the drive when the
brake is released or the motor is removed.
In automatic mode the brake is permanently released. Therefore,
it is not exposed to wear and does usually not require any
readjustment.
A
Thickness gauge
B
Groove
Figure 16: Brake (rubber cap removed)
However, if you want to check the brake gap, proceed as follows:
1. Disconnect the actuator from mains supply.
2. Remove hood (PME120AI incl. electronic unit).
3. Remove the rubber cover of the motor.
4. Unscrew the two grub screws 1.
5. Put two thickness gauges (0.15 mm / 0.0059 in)
diametrically opposed between the two plates 2and 3.
6. Press plate 1 down.
7. Tighten the two grub screws 1

14 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
6Electrical connections
WARNING
Risk of injury due to live parts!
Risk of death or serious injuries due to electricity and
unexpected machine movements. In automatic mode the
motor is always under power, even at standstill.
• When working on the actuator or the related subassembly,
switch off the supply voltage for the electronic unit and
separate anti-condensation heater (option), and take
precautions to prevent unintentional switch-on.
General
1
Plug housing
2
Carrier
3
Crimp carrier
4
Cables with crimp pins
5
Terminal carrier
6
Cables with cable end sleeve
7
Male carrier
Figure 17: Exemplary illustration of cable connection to the actuator; plug housing may
contain alternatively a terminal carrier or a crimp carrier.
The cable between actuator and electronic unit is connected to
the electronic unit via terminals and to the actuator via a plug.
The plug housing may contain a carrier for terminals or for the
cable ends with crimp sockets.
Actuator versions
Electrical rotary actuators PME120 are available in two versions:
• PME120-AI (with integrated electronic unit)
• PME120-AN (for separate electronic units)
PME120-AI
PME120-AI
Electronic unit
Figure 18: PME120AI with dismounted electronic unit
PME120-AN
PME120
-AN
Electronic unit EAN823
for field installation
Electronic unit
EAS822 for rack
installation
Figure 19: PME120-AN with available, separate electronic units

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 15
Removal of integrated electronic unit
A
Electronic unit
Figure 20: PME120-AI
Note
If you want to use a faultless running electronic unit for another
actuator, it is absolutely necessary to delete the basic settings
of the operating range before you remove it. Press the drive
buttons and on the LCP for at least 5 sec. until both LED
flash simultaneously.
For the removal proceed as follows:
1. Switch-off the power supply and disconnect the plug.
2. Loosen the 4 fastening screws 1.
3. Pull the electronic unit slightly apart.
Covers
A
Screws
B
Cover or similar component
Figure 21: Exemplary cover
Terminal covers and other components at the Contrac actuators
and electronic units are fastened with 4 or more screws (only 2
screws for local control panel cover).
In some cases, they are additionally sealed with a soft rubber
gasket. In order to avoid a gap between the housing and the
cover (or the other component) tighten these screws evenly
crosswise according to the order in the basic sketch in Figure 34
to get an even load.
Start with one screw and tighten it slightly. Then tighten the 2nd,
opposite screw in the same manner. Continue with the
remaining screws. Finally tighten the screws in the same order.
This will ensure a tight seal.

16 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 6 Electrical connections
Integrated PME120-AI Electronic unit
Analog / Digital
Note
The electrical connection is established via a universal plug on the actuator.
BE = digital input
BA = digital
output
Figure 22: Control via analog input 0/4 to 20 mA, HART® communication or digital inputs

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 17
PROFIBUS DP®
Note
The electrical connection is established via a universal plug on the actuator.
DO = digital output
Figure 23: Control via fieldbus PROFIBUS DP® (PME120-AI, LME620-AI)
Note
Detailed information on separate electronic units can be found in the corresponding operating instruction.

18 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 6 Electrical connections
Electronic unit EAN823 (Contrac) for PME120-AN
Analog / Digital
Note
• The electrical connection is provided by a universal plug on the actuator and the screw terminals on the electronic unit.
• If you are using a separate heat supply, the heater must be protected with a 2 to 6 A medium time-lag fuse (e.g. NEOZED D01 E14).
BE = digital input
BA = digital output
Figure 24: Control via analog input 0/4 to 20 mA, HART® communication or digital inputs

PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A 19
PROFIBUS DP®
Note
• The electrical connection is provided by a universal plug on the actuator and the screw terminals on the electronic unit.
• If you are using a separate heat supply, the heater must be protected with a 2 to 6 A medium time-lag fuse (e.g. NEOZED D01 E14).
BA = digital output
Figure 25: Control via fieldbus PROFIBUS DP®

20 PME120-AI / PME120-AN (Contrac) ELECTRICAL ROTARY ACTUATOR | SEI/PME120-EN REV. A
… 6 Electrical connections
Electronic unit EAS822 (Contrac) for PME120-AN
Analog / Digital
Note
• The electrical connection is provided by a universal plug on the actuator and the screw terminals on the electronic unit.
• If you are using a separate heat supply, the heater must be protected with a 2 to 6 A medium time-lag fuse (e.g. NEOZED D01 E14).
BE = digital input
BA =
digital output
Figure 26: Control via analog input 0/4 to 20 mA, HART® communication or digital inputs