ABB i-bus SA/S 2.6.2.1 User manual

ABB i-bus®KNX
SA/S Switch Actuators
Product Manual

ABB i-busKNX
General
SA/S | 2CDC 505 056 D0208 5
1 General
KNX systems provide an attractive solution that meets the most demanding residential, commercial and
public buildings requirements. High living standards, comfort and safety can be easily combined with cost-
effectiveness and environmental awareness using KNX bus systems from ABB. KNX products cover the
entire range of buildings applications, from illumination and blind control to heating, ventilation, energy
management, security and surveillance. These requirements can be met cost-effectively with minimal
planning and installation effort using the ABB KNX. Furthermore, flexible room usage and continuous
adaptation to changing requirements are simple to implement. SA/S Switch Actuators fulfill individual
requirements in industrial, commercial and public buildings as well as in the private sector for controlling
switchable loads, e.g.:
•Illumination
•Heating control
•Signaling equipment
Certain types of Switch Actuator can also detect and monitor load current via a threshold value function.
Based on the load current detected, responses can be triggered via KNX and the load can be switched off
directly or switched via KNX.
1.1 Using the product manual
This manual provides you with detailed technical information on the ABB i-bus®SA/S Switch Actuator
range, its installation and programming.
Application of the device is explained using examples.
This manual is subdivided into the following sections:
Section 1 General
Section 2 Device technology
Section 3 Commissioning
Section 4 Planning and application
Section A Appendix

ABB i-busKNX
General
62CDC 505 056 D0208 | SA/S
1.1.1 Structure of the product manual
All parameters are described in section 3.
Please note
This product manual describes all the current 2/4/8 and 12-fold Switch Actuators. However, as the
functions for all outputs are identical, only the functions of output A will be described.
Where information in the product manual refers to all outputs, the description output A...X is used. 2-fold
corresponds to outputs A...B, 4-fold corresponds to outputs A...D, 8-fold corresponds to outputs A...H
and 12-fold corresponds to outputs A...L.
Variants with current detection feature an additional parameter page as well as additional
communication objects for this function.
1.1.2 Notes
Notes and safety instructions are represented as follows in this product manual:
Please note
Tips for usage and operation
Example
Application examples, installation examples, programming examples
Important
These safety instructions are used as soon as there is danger of a malfunction without risk of damage
or injury.
Caution
These safety instructions are used if there is a danger of damage with inappropriate use.
Danger
These safety instructions are used if there is a danger to life and limb with inappropriate use.
Danger
These safety instructions are used if there is an extreme danger to life with inappropriate use.

ABB i-busKNX
General
SA/S | 2CDC 505 056 D0208 7
1.2 Product and functional overview
SA/S
12.16.6.1
ABB i-bus®KNX SA/S Switch Actuators are modular installation devices with module widths of
2/4/8/12 units in ProMdesign for installation in a distribution board.
Connection to the ABB i-bus®is established via a bus connection terminal on the front.
The Switch Actuators require no auxiliary voltage.
The assignment of the physical address as well as the parameterization is carried out with
Engineering Tool Software (ETS), version ETS2 V1.3a or higher. If using ETS3 or ETS4 you
will need to import the corresponding application program.
Please note
The illustrations of the parameter windows in this manual correspond to the ETS3 parameter
windows. The user program is optimized for ETS3.
In ETS2 the parameter page for any parameter being used may split automatically.
The Switch Actuators can switch 2 to 12 independent electrical AC or three-phase loads via
KNX with floating contacts. With SA/S x.16.6.1 types it is possible to detect the load current for
each output. The outputs of the 6 A, 10 A, 16 A and 16/20 A Switch Actuators can be switched
on and off manually.
Switch Actuators SA/S x.16.6.1 and SA/S 12.16.5.1, which have the highest switching capacity
(C-load), are particularly well-suited for switching loads with high peak inrush currents, e.g.
lighting equipment with compensation capacitors or fluorescent lamp loads (AX) to EN 60 669.
The following functions can be set individually for each output:
•Time and ON/OFF delay functions
•Staircase lighting function with warning and modifiable staircase lighting time
•Recall of scenes/presets via 8/1 bit commands
•Logical functions AND, OR, XOR, GATE function
•Status messages
•Forced operation and safety functions
•Response to threshold values
•Control of electro-thermal valve drives
•Selection of the default state on bus voltage failure and recovery
•Output inversion
SA/S
8.16.6.1
SA/S
4.16.2.1
SA/S
2.10.2.1
SA/S
8.6.2.1
SA/S
8.6.1.1
SA/S
4.6.1.1

ABB i-busKNX
General
82CDC 505 056 D0208 | SA/S
On Switch Actuators with current detection, SA/S x.16.6.1, each output also features the load current
detection function with parameterizable response to two current threshold values. The current value can
be sent via the bus. Individual outputs in the Switch Actuators can be copied or exchanged to minimize
programming work.
The SA/S x.16.6.1 and SA/S x.16.5.1 are suitable for rated currents up to 20 A and have C-load switching
capacity.
In the following table you will find an overview of the ABB i-bus®Switch Actuators and their type
designations:
– SA/S 2.6.2.1 SA/S 2.10.2.1 SA/S 2.16.2.1 SA/S 2.16.5.1 SA/S 2.16.6.1
SA/S 4.6.1.1 SA/S 4.6.2.1 SA/S 4.10.2.1 SA/S 4.16.2.1 SA/S 4.16.5.1 SA/S 4.16.6.1
SA/S 8.6.1.1
SA/S 8.6.2.1
SA/S 8.10.2.1
SA/S 8.16.2.1
SA/S 8.16.5.1
SA/S 8.16.6.1
SA/S 12.6.1.1 SA/S 12.6.2.1 SA/S 12.10.2.1 SA/S 12.16.2.1 SA/S 12.16.5.1 SA/S 12.16.6.1
Please note
The codes represent the following:
SA/S x.y.z.w
x = number of outputs (2, 4, 8 or 12)
y = rated current in Amperes (6, 10, 16)
z = load type specification:
1 = type with no manual operation
2 = type with manual operation
5 = type with higher switch capacity, C-load (200 µF)
6 = type with higher C-load switching capacity and current detection
w = version number

ABB i-busKNX
Device technology
SA/S | 2CDC 505 056 D0208 9
2 Device technology
2.1 Switch Actuators SA/S x.6.1.1, 6 A, MDRC
SA/S
12.6.1.1
Switch Actuators SA/S
x.6.1.1 6 A are
modular installation devices in Pro
M
design for installation in the distribution
board. They are suitable for switching
resistive, inductive and capacitive loads.
The actuators can
switch up to
12
independent electrical loads via
floating contacts. The outputs are
connected using screw terminals in
groups of two
contacts for SA/S 8.6.1.1
and SA/S
12.6.1.1. SA/S 4.6.1.1 has one
terminal per output for power feed. Each
output is contr
olled separately via KNX,
regardless of the variant.
The device does not require an
additional power supply and is ready for
immediate use after the bus voltage
has been applied. The Switch Actuator
is parameterized via ETS. Connection
to KNX is implemented using the bus
connection terminal on the front.
2.1.1 Technical data
Supply KNX bus voltage 21…32 V DC
Current consumption, bus < 12 mA
Power consumption
Maximum 250 mW
Rated output value
SA/S type 4.6.1.1 8.6.1.1 12.6.1.1
Current detection no no no
Number (floating contacts 2/group) 4 *) 8 12
Unrated voltage 250/440 V AC (50/60 Hz)
Inrated current (per output) 6 A 6 A 6 A
Leakage loss per device at max. load 1.5 W 2.0 W 2.5 W
Output switching current AC31) operation (cos ϕ= 0.45)
To EN 60 947-4-1 6 A/230 V AC
AC3
1)
operation (cos ϕ= 0.8)
To EN 60 947-4-1 6 A/230 V AC
Fluorescent lighting load to EN 60 669-1 6 A/250 V AC (35 µF)
2)
Minimum switching capacity 20 mA/5 V AC
10 mA/12 V AC
7 mA/24 V AC
Output service life
Mechanical service life
> 107
Electrical endurance
To IEC 60 947-4-1
AC11) (240 V/cos ϕ = 0.8) > 105
AC3
1)
(240 V/cos ϕ = 0.45) > 1.5 x 10
4
AC5a
1)
(240 V/cos ϕ = 0.45) > 1.5 x 10
4
*) Each output has one terminal for power feed.
2CDC 071 033 S0012

ABB i-busKNX
Device technology
10 2CDC 505 056 D0208 | SA/S
Output switching times 3)
Maximum output relay position change per
minute if all relays are switched simultaneously.
The position changes should be distributed
equally within the minute.
4.6.1.1 8.6.1.1 12.6.1.1
60 30 20
Maximum output relay position change per
minute if only one relay is switched.
240 240 240
Connections KNX
Load circuits
Tightening torque
Operating and display elements
Programming button/LED
Degree of protection
IP 20
Protection class
II
Isolation category Overvoltage category
Pollution degree
Via bus connection terminals,
0.8 mm Ø, solid
Universal head screw terminal (PZ 1)
0.2… 4 mm2 fine stranded, 2 x 0.2…2.5 mm2
0.2… 6 mm2 solid, 2 x 0.2…4 mm2
max. 0.6 Nm
For assignment of physical address To EN 60
529
To EN 61 140
III to EN 60 664-1
2toEN60 664-1
KNX safety extra low voltage SELV 24 V DC
Temperature range Operation
Storage
Transport
- 5 °C…+45 °C
-25 °C…+55 °C
-25 °C…+70 °C
Ambient conditions
Maximum air humidity 95 %, no condensation allowed
Design
Modular installation device (MDRC) Modular installation device, ProM
SA/S type 4.6.1.1 8.6.1.1 12.6.1.1
Dimensions 90 x W x 64.5 mm (H x W x D)
Width W in mm 72 108 144
Mounting width in units (18 mm modules) 4 6 8
Mounting depth in mm 64.5 64.5 64.5
Weight
in kg
0.13 0.24 0.3
Mounting
On 35 mm mounting rail
To EN 60 715
Mounting position
As required
Housing/color Plastic housing, gray
Approvals KNX to EN 50 090-1, -2 Certification
CE mark in accordance with the EMC guideline and
low voltage guideline
1)
Further information concerning electrical endurance to IEC 60 947-4-1 can be found at: AC1, AC3, AX, C-load specifications, p. 43
2) The maximum inrush current peak may not be exceeded.
3) The specifications apply only after the bus voltage has been applied to the device for at least 30 seconds. Typical relay delay is approx. 20 ms.

ABB i-busKNX
Device technology
SA/S | 2CDC 505 056 D0208 11
2.1.2 Lamp output load

at 230 V AC
Lamps Incandescent lamp load 1,200 W
Fluorescent lamps T5/T8 Uncorrected
Parallel compensated
DUO circuit
800 W
300 W
350 W
Low-voltage halogen lamps
Inductive transformer
Electronic transformer
Halogen lamps 230 V
800 W
1,000 W
1,000 W
Dulux lamp Uncorrected
Parallel compensated 800 W 800 W
Mercury-vapor lamp
Uncorrected
Parallel compensated 1,000 W 800 W
Switching capacity (switching contact)
Maximum peak inrush current Ip(150 µs)
Maximum peak inrush current Ip(250 µs)
Maximum peak inrush current Ip(600 µs)
200 A
160 A
100 A
Number of electronic ballasts (T5/T8, single
element)1)
18 W (ABB EVG 1 x 18 SF)
24 W (ABB EVG-T5 1 x 24 CY)
36 W (ABB EVG 1 x 36 CF)
58 W (ABB EVG 1 x 58 CF)
80 W (Helvar EL 1 x 80 SC)
10
10
7
5
3
1) For multiple element lamps or other types, the number of electronic ballasts must be determined using the peak inrush current of the electronic
ballasts, see Ballast calculation, p. 42
Device type Application program Maximum number of
communication objects Maximum number of group addresses Maximum number of associations
SA/S 4.6.1.1 Switch 4f 6A/…* 64 254 254
SA/S 8.6.1.1 Switch 8f 6A/…* 124 254 254
SA/S 12.6.1.1 Switch 12f 6A/…* 184 254 254
* … = current version number of the application program
Please note
ETS and the current version of the device application program are required for programming.
The current application program is available for download at www.abb.com/knx. After import into ETS
it can be found under ABB/Output/Binary output xf 6A/…* (x = 4, 8 or 12).
The device does not support the locking function of a KNX device in ETS. If you inhibit access to all of
the project devices by using a BCU code, it has no effect on this device.
Data can still be read and programmed.

ABB i-busKNX
Device technology
12 2CDC 505 056 D0208 | SA/S
2.1.3 Connection schematic SA/S x.6.1.1
1 Label carrier
2 Programming button
3 Programming LED
4 Bus connection terminal
5 Load current circuits, one screw terminal for phase connection per contact
Danger
Touch voltages.
Danger of injury.
Observe all-pole disconnection.
2CDC 072 07x F0011

ABB i-busKNX
Device technology
SA/S | 2CDC 505 056 D0208 13
2.1.4 Dimension drawing

SA/S x.6.1.1
SA/S 4.6.1.1
SA/S 8.6.1.1
SA/S 12.6.1.1
Width W
Mounting width
(18 mm modules)
72 mm
4 units
108 mm
6 units
144 mm
8 units
2CDC 072 077 F0011