ABB JSM D28 User manual

2TLC010040M0201 REV. B 1/5
—
SAFETY PRODUCTS
Installation guide
JSM D28 Handle profile for Magne
JSM D28 is an aluminum profile used as door handle for Magne 3 and Magne 4 on hinged (conventional)
doors. Designed for doors with a minimum opening radius of 200 mm.
Installation shall be done in accordance with a risk assessment for the individual application.
Installation must be carried out by authorized personnel and in accordance with instructions in this
document and the ‘Magne Product Manual’.
Read and understand ‘Magne Product manual’ and ‘Eden Product manual’ before starting the
installation. Manuals are found at www.abb.com/jokabsafety
Parts overview
Product ID
Description
2TLA042023R0100
JSM D28 Handle profile in aluminum
The mounting kit includes all bolts and nuts necessary to install Magne on ABB Quick-Guard © fencing
system.
Note!
Magne, Eva, anchor plate and cellular rubber are not included in the
kit. These items
must be ordered separately
.
Handle profile (x1)
Cover profile (x1)
End cover (x1)
End cover with hole
for cabling (x1)
Special nut
Centering plate

INSTALLATION GUIDE
REV. B 2/5
Dimensions
All dimensions are in millimeter (mm).
Handle profile dimensions
Installation and orientation of Eva sensor
Depending on how Magne is installed on the fence, Eva and the anchor plate can be installed in two
ways. Ensure that Eva is installed and oriented in the holes to which the corresponding Magne model is
installed. See figures below for alternative ways of installation and orientation of Eva.

INSTALLATION GUIDE
REV. B 3/ 5
Installation and assembly
Note!
In the following step by step instructions, a Magne 4 is
installed.
1.
Pre-assemble Magne (D) using screw (A),
centering plate (B) and special nut (C
) and install
it on the door post
.
2. Install Eva sensor with self-tapping screw
4.2 x 25 (x2). Make sure Eva is oriented correctly
and that the correct installation holes are used.
Note!Installation and orientation position of
Eva depends on Magne model and how Magne is
installed on the fence. Use DA 2B spacers (x2),
one in each hole at the back side of Eva.
3.
Install positioning/stop screw (J) 4.2 x 25 (x1)
and
DA 2B spacer (K) (x4) for the anchor plate.
4. Pre-assemble the anchor plate (B) with cellular
rubber (C). Tighten the screw M8 x 18 (F) by hand,
do not use any tool.
Note! Do not overtighten the screw. This can
deform the anchor plate, causing reduced or no
holding force. A deformed anchor plate shall be
replaced.

INSTALLATION GUIDE
REV. B 4/5
5
. Insert/slide the anchor plate into the handle
profile
.
6. Install the positioning/stop screw (J) 4.2 x 25 (x
1)
and DA 2B spacer (K) (x4) for the anchor plate.
7.
Pre-assemble the handle profile (H) using suitable length of M6 screw (A), washer (R), centering plate
(B) and special nut (C).
8. Install end cap (N) (x2) on both sides of the profile using self-tapping screws (O) 3.5 x 13 (x6).
Note! End cap with opening for cabling can be installed on any profile end.
The fourth screw is
installed later (see step 11).

INSTALLATION GUIDE
REV. B 5/5
9.
Install the handle profile on the door and
fasten with screws (A). M
ake sure the profile
placement is aligned with Magne
.
10. Insert the cover profile (P).
11.
Install the two remaining self-tapping screws
(O)
3.5 x 13 mm (x2) to fixate the cover plate and
to finalize the installation
.
12. Check the function by opening and closing
the door several times.
Complete product range and accessories are found at www.abb.com/jokabsafety