ABB FSM4000-SE41F User manual

Operating Instruction
D184B140U02
Electromagnetic Flowmete
r
FSM4000
Valid for software versions C.10 and higher
Model FSM4000-SE41F
FSM4000-SE21
FSM4000-SE21F
FSM4000-S4

Blinder Text
2 FSM4000 D184B140U02
Electromagnetic Flowmeter
FSM4000
Operating Instruction
D184B140U02
02.2018
Rev. D
Original instruction
Manufacturer:
ABB Automation Products GmbH
Measurement & Analytics
Dransfelder Straße 2
D-37079 Göttingen
Germany
Tel.: [phone]
Fax: [phone]
Phone: [phone]
[email protected]
© Copyright 2018 by ABB Automation Products GmbH
Subject to changes without notice
This document is protected by copyright. It assists the user in safe and efficient operation of the device.
The contents of this document, whether whole or in part, may not be copied or reproduced without prior
approval by the copyright holder.
Contents

Contents
D184B140U02 FSM4000 3
1Safety.............................................................................................................................................................6
1.1General information and notes for the reader ................................................................................................6
1.2Intended use...................................................................................................................................................7
1.3Improper use ..................................................................................................................................................7
1.4Target groups and qualifications ....................................................................................................................7
1.5Warranty provisions........................................................................................................................................7
1.5.1Safety-/ warning symbols, note symbols.................................................................................................8
1.5.2Name Plate / Factory Tag .......................................................................................................................9
1.6Transport safety information.........................................................................................................................12
1.7Installation safety information.......................................................................................................................12
1.8Electrical installation safety information .......................................................................................................12
1.9Safety instructions for operation...................................................................................................................13
1.10Technical limit values ...................................................................................................................................13
1.11Allowed Fluids ..............................................................................................................................................13
1.12Maintenance and inspection safety information...........................................................................................14
1.13Returning devices.........................................................................................................................................14
1.14Integrated management system...................................................................................................................15
1.15Disposal........................................................................................................................................................15
1.15.1Information on WEEE Directive 2012/19/EU (Waste Electrical and Electronic Equipment).................15
2Design and function...................................................................................................................................16
2.1Measuring principle ......................................................................................................................................16
2.2Design ..........................................................................................................................................................17
2.3Device designs .............................................................................................................................................17
3Transport.....................................................................................................................................................18
3.1Inspection .....................................................................................................................................................18
3.2General information on transport .................................................................................................................18
3.3Transport of flanged units up to nominal diameter DN 300 .........................................................................18
3.4Transport of flanged units larger than nominal diameter DN 350 ................................................................19
4Mounting .....................................................................................................................................................20
4.1General information on installation...............................................................................................................20
4.2Supports for nominal diameters larger than DN 350....................................................................................20
4.3Mounting the meter tube ..............................................................................................................................21
4.4Torque information .......................................................................................................................................22
4.4.1Flanged units and units with adapter flange, model SE41F / SE21F / SE21W....................................22
4.4.2Variable process connections model SE21 ..........................................................................................25
4.5Information on 3A conformity .......................................................................................................................26
4.6Installation Requirements.............................................................................................................................27
4.6.1Electrode axis........................................................................................................................................27
4.6.2In- and outlet pipe sections ...................................................................................................................27
4.6.3Vertical connections ..............................................................................................................................27
4.6.4Horizontal connections..........................................................................................................................27
4.6.5Free inlet or outlet .................................................................................................................................27
4.6.6Strongly contaminated fluids.................................................................................................................27
4.6.7Installation in the vicinity of pumps .......................................................................................................28
4.6.8Installing the high temperature design ..................................................................................................28
4.6.9Installation in pipelines with larger nominal diameter ...........................................................................28
4.7Flowmeter Sizes, Pressure Ratings, Flow Range........................................................................................29

Contents
4 FSM4000 D184B140U02
4.8Ground..........................................................................................................................................................30
4.8.1General information on ground connections.........................................................................................30
4.8.2Metal pipe with fixed flanges.................................................................................................................30
4.8.3Metal pipe with loose flanges................................................................................................................31
4.8.4Non-metallic pipes or pipes with insulating liner ...................................................................................31
4.8.5Flowmeter sensor in stainless steel design model SE21......................................................................32
4.8.6Ground for devices with protective plates.............................................................................................32
4.8.7Ground with conductive PTFE grounding plate ....................................................................................32
5Electrical connections ...............................................................................................................................33
5.1Preparing and routing the signal and magnet coil cable ..............................................................................33
5.2Connecting the flowmeter sensor.................................................................................................................35
5.2.1Connecting the signal and magnet coil cables .....................................................................................35
5.2.2Protection class IP 68 ...........................................................................................................................36
5.3Connecting the transmitter ...........................................................................................................................38
5.3.1Supply power connection......................................................................................................................38
5.3.2Connecting the signal and magnet coil cables .....................................................................................39
5.4Terminal connection diagrams .....................................................................................................................40
5.5Connection examples for peripherals (incl. HART)......................................................................................44
6Commissioning ..........................................................................................................................................47
6.1Preliminary checks prior to start-up..............................................................................................................47
6.2Commissioning the unit ................................................................................................................................49
6.2.1Switching on supply power ...................................................................................................................49
6.2.2Device configuration..............................................................................................................................49
6.3Easy Set-up: For uncomplicated configuration ............................................................................................51
6.4Commissioning PROFIBUS PA units...........................................................................................................52
6.4.1Information on voltage/current consumption.........................................................................................54
6.4.2System integration ................................................................................................................................55
6.5Commissioning FOUNDATION Fieldbus units.............................................................................................56
7Parameterization ........................................................................................................................................58
7.1Display options .............................................................................................................................................58
7.2Data entry.....................................................................................................................................................59
7.3Entering data in “short form”.........................................................................................................................61
7.4Additional information regarding use of enhanced diagnostic functions......................................................88
7.4.1Determining measurement values for diagnostics................................................................................88
7.4.2Recommended settings for diagnostic limit values...............................................................................92
7.4.3Displaying the diagnostic values...........................................................................................................94
7.4.4Readjusting the coil temperature ..........................................................................................................97
7.5Software history............................................................................................................................................98
7.5.1For transmitters without communication or HART protocol ..................................................................98
7.5.2For transmitter with PROFIBUS PA communication.............................................................................99
7.5.3For transmitter with FOUNDATION Fieldbus communication ..............................................................99
8Messages and tests .................................................................................................................................100
8.1Overview of error states and alarms ..........................................................................................................100
8.2Error messages during operation and with data entry ...............................................................................101
8.3Warning messages during operation .........................................................................................................103
9Maintenance / Repair ...............................................................................................................................105
9.1Flowmeter sensor.......................................................................................................................................105
9.2Gaskets ......................................................................................................................................................105

Contents
D184B140U02 FSM4000 5
9.3Replacing the transmitter ...........................................................................................................................106
10Spare parts list .........................................................................................................................................108
10.1Fuses for transmitter electronics ................................................................................................................108
10.2Spare parts for transmitter S4 ....................................................................................................................109
10.2.1Field housing unit ................................................................................................................................109
10.3Spare parts flowmeter sensor ....................................................................................................................110
10.3.1Terminal box, stainless steel, DN 1 ... DN 100 ...................................................................................110
10.3.2Terminal box, aluminum, DN 3 ... DN 1000 ........................................................................................111
11Operating S4 with an older sensor.........................................................................................................112
12Specifications ...........................................................................................................................................115
12.1Measuring accuracy ...................................................................................................................................115
12.1.1Reference conditionsper EN 29104 ....................................................................................................115
12.1.2Maximum measuring error ..................................................................................................................115
12.2Flowmeter sensor.......................................................................................................................................116
12.2.1Flowmeter sensor SE41F ...................................................................................................................116
12.2.2Flowmeter sensor SE21 / SE21F........................................................................................................119
12.3Transmitter S4............................................................................................................................................121
13Appendix ...................................................................................................................................................122
13.1Other applicable documents.......................................................................................................................122
13.2Approvals and certifications .......................................................................................................................122
13.3Overview of setting parameters and technical design ...............................................................................123
13.4Return form ................................................................................................................................................124

Safety
6 FSM4000 D184B140U02
1 Safety
1.1 General information and notes for the reader
You must read these instructions carefully prior to installing and commissioning the device.
These instructions are an important part of the product and must be kept for future reference.
These instructions are intended as an overview and do not contain detailed information on all
designs for this product or every possible aspect of installation, operation and maintenance.
For additional information or if specific problems occur that are not discussed in these
instructions, contact the manufacturer.
The content of these instructions is neither part of any previous or existing agreement, promise
or legal relationship nor is it intended to change the same.
This product is built based on state-of-the-art technology and is operationally safe. It has been
tested and left the factory in perfect working order from a safety perspective. The information in
the manual must be observed and followed in order to maintain this state throughout the period
of operation.
Modifications and repairs to the product may only be performed if expressly permitted by these
instructions.
Only by observing all of the safety instructions and all safety/warning symbols in these
instructions can optimum protection of both personnel and the environment, as well as safe and
fault-free operation of the device, be ensured.
Information and symbols directly on the product must be observed. They may not be removed
and must be fully legible at all times.

Safety
D184B140U02 FSM4000 7
1.2 Intended use
This device is intended for the following uses:
• To transmit fluid, pulpy or pasty substances with electrical conductivity.
• To measure the flowrate of the operating volume or mass flow units (at constant pressure /
temperature), if a mass engeineering unit is selected.
The following items are included in the intended use:
• Read and follow the instructions in this manual.
• Observe the technical ratings; refer to the section 1.10 „Technical limit values“.
• Use only allowed liquids for measurement; refer to the section 1.11 „Allowed Fluids ”..
1.3 Improper use
The following are considered to be instances of improper use of the device:
• Operation as a flexible adapter in piping, e.g., to compensate for pipe offsets, pipe vibrations,
pipe expansions, etc.
• As a climbing aid, e. g., for mounting purposes
• As a support for external loads, e. g., as a support for piping, etc.
• Adding material, e. g., by painting over the name plate or welding/soldering on parts
• Removing material, e. g., by spot drilling the housing
1.4 Target groups and qualifications
Installation, commissioning, and maintenance of the product may only be performed by trained
specialist personnel who have been authorized by the plant operator to do so. The specialist
personnel must have read and understood the manual and comply with its instructions.
Prior to using corrosive and abrasive materials for measurement purposes, the operator must
check the level of resistance of all parts coming into contact with the materials to be measured.
ABB Automation Products GmbH will gladly support you in selecting the materials, but cannot
accept any liability in doing so.
The operators must strictly observe the applicable national regulations with regards to
installation, function tests, repairs, and maintenance of electrical products.
1.5 Warranty provisions
Using the device in a manner that does not fall within the scope of its intended use, disregarding
this instruction, using underqualified personnel, or making unauthorized alterations releases the
manufacturer from liability for any resulting damage. This renders the manufacturer's warranty
null and void.

Safety
8 FSM4000 D184B140U02
1.5.1 Safety-/ warning symbols, note symbols
DANGER – <Serious damage to health / risk to life>
This symbol in conjunction with the signal word "Danger" indicates an imminent danger.
Failure to observe this safety information will result in death or severe injury.
DANGER – <Serious damage to health / risk to life>
This symbol in conjunction with the signal word "Danger" indicates an imminent electrical
hazard. Failure to observe this safety information will result in death or severe injury.
WARNING – <Bodily injury>
This symbol in conjunction with the signal word “Warning“ indicates a possibly dangerous
situation. Failure to observe this safet
y
information ma
y
result in death or severe in
j
ur
y
.
WARNING – <Bodily injury>
This symbol in conjunction with the signal word "Warning" indicates a potential electrical
hazard. Failure to observe this safety information may result in death or severe injury.
CAUTION – <Minor injury>
This symbol in conjunction with the signal word “Caution“ indicates a possibly dangerous
situation. Failure to observe this safety information may result in minor or moderate injury.
This ma
y
also be used for propert
y
dama
g
e warnin
g
s.
ATTENTION – <Property damage>!
The symbol indicates a potentially damaging situation.
Failure to observe this safety information may result in damage to or destruction of the product
and/or other system components.
IMPORTANT (NOTICE)
This symbol indicates operator tips, particularly useful information, or important information
about the product or its further uses. It does not indicate a dan
g
erous or dama
g
in
g
situation.

Safety
D184B140U02 FSM4000 9
1.5.2 Name Plate / Factory Tag
The factory tag or name plate can be found at the following locations on the unit housing:
G00522
31
2
Fig. 1
1Name plate, flowmeter sensor
2Factory tag plate, flowmeter sensor
3Name plate, transmitter
1.5.2.1 Identifying the device design
1.Identifying the model:
The model number of the flowmeter sensor or transmitter (see nos. 1 or 2 in the description
of the name plates) can be found on the name plate. The connection diagram for the
respective model is contained in the section “Terminal connection diagrams”. Technical data,
material load curves, etc., are organized by model in the section “Technical data”.
2.Identifying the transmitter design:
The transmitter design can be identified from the name plate on the transmitter housing.
3.Identifying the software version:
The software version can be displayed when the transmitter is switched on.

Safety
10 FSM4000 D184B140U02
1.5.2.2 Name plate
Flowmeter sensor
ABB Automation Products GmbH
37070 Göttingen – Germany
Material:
Tmax:
Pmax: < 30 VA
Phase:
000221498 / X001
PFA / Hastelloy C-4
130 °C
90°
DN 10 PN 40
IP 67
URef: 0.280 V
Qmax DN: 45.0 l/min
Cs: -31.3500 % Cz: -0.5052 %
Model SE21
Order no:
G00523
2
1
3
5
7
11
13
9
4
6
8
10
12
Fig. 2
1Model no.
2CE mark (EC conformity)
3Order no.
4 Measuring tube lining /
Electrode material
5Nominal size / Nominal pressure
6Max. fluid temperature
7Protection class of housin
g
8Max. flowrate at v = 10 m/s
9Power consumption
10Phase relationship between signal and
reference voltages
11Reference voltage
12Cs calibration factor “span”
13Cz calibration factor "zero point"
Transmitter
ABB Automation Products GmbH
37070 Göttingen – Germany
S4
0002238521 / Y001
U/fnenn: 85-253 V AC / 50/60 Hz
<45VA
G00524
Signal converter S4
Model No.:
Order No.:
Power supply:
Pulse output / Communication:
Smax:
passive HART
Comment: do not connect to EEx Primary
2
1
3
4
5
6
7
Fig. 3
1CE mark (EC conformity)
2Model no.
3Order no.
4 Power supply - Voltage range /
frequency
5Power for transmitter and flowmeter
sensor
6Version acc. to order with/without HART
protocol or PROFIBUS PA or
FOUNDATION Fieldbus
7Version acc. to active (24 V pulse) or
passive (optocoupler) (active or passive can
be changed onsite)

Safety
D184B140U02 FSM4000 11
1.5.2.3 Factory Tag
The factory tag is located on the flowmeter sensor housing. If the pressure equipment is subject
to the PED (see section 3 para. 3 PED 2014/68/EU), two labels are required:
Pressure equipment subject to PED
S.-Nr.: 0012345
0045
DN50/PN40
Material: 1.4571 / PTFE
Manufactured: 2002 PED: Fluid 1, Gas
ABB Automation Products GmbH
37070 Göttingen - Germany
/ Hast.C-4
1
2
3
4
5
6
G00002
Fig. 4
1CE mark (with number of labeled
location) to confirm the device meets the
requirements of pressure equipment
directive 2014/68/EU.
2Serial number for identification of the
pressure equipment by the manufacturer.
3Nominal size and nominal pressure rating
of pressure equipment.
4Flange material, liner material and
electrode material (wetted parts).
5Year of manufacture and specification of
fluid group as per the pressure
equipment directive (PED). Fluid group 1
= hazardous liquids, gaseous.
6Manufacturer of the pressure equipment.
Pressure equipment outside the applicable range of the PED
S.-Nr.: 0012345
DN50/PN40
Material: 1.4571 / PTFE
Manufactured: 2002 PED: SEP
ABB Automation Products GmbH
37070 Göttingen - Germany
/ Hast.C-4
G00003
Fig. 5
The factory tag contains most of the specifications included on the plate described above with
the following differences:
• There is no CE mark because the pressure equipment, as per section 3 para. 3 of the PED,
is outside the applicable range of the pressure equipment directive 2014/68/EU.
• The reason for the exception is specified in section 3 para. 3 of the PED. The pressure
equipment is categorized as SEP (= sound engineering practice).
Important
If the factory tag is not present, the device is not in compliance with directive 2014/68/EU. The
exception applies for water, power and connected equipment accessories in accordance with
g
uideline 1/16 of sec. 1 para. 3.2 of the pressure equipment directive.

Safety
12 FSM4000 D184B140U02
1.6 Transport safety information
• Depending on the device, the center of gravity may not be in the center of the equipment.
• The protection plates or protective caps installed on the process connections of devices lined
with PTFE / PFA must not be removed until just before installation; to prevent possible
leakage, make sure that the liner on the flange is not cut or damaged.
Check the devices for possible damage that may have occurred from improper transport.
Damages in transit must be recorded on the transport documents. All claims for damages must
be submitted to the shipper without delay and before installation.
1.7 Installation safety information
Observe the following instructions:
• The flow direction must correspond to the direction indicated on the device, if labeled.
• Comply with the maximum torque for all flange bolts.
• Install the devices without mechanical tension (torsion, bending).
• Install flange and wafer type units with coplanar counter flanges.
• Only install devices for the intended operating conditions and with suitable seals.
• Secure the flange bolts and nuts against pipeline vibrations.
1.8 Electrical installation safety information
The electrical connection may only be performed by authorized specialists according to the
electrical plans.
Comply with electrical connection information in the manual. Otherwise, the electrical protection
can be affected.
Ground the flowmeter and sensor housing.
The line for the supply power must be installed according to the relevant national and
international standards. A separate fuse must be connected upstream and in close proximity to
each unit. The fuses must be identified accordingly. The unit has a protection class of I and
overvoltage class II (IEC664).
The power supply and the electrical circuit for the coils of the sensor are dangerous and pose a
contact risk.
The coils and signal circuit can be connected with ABB sensors only. Use the supplied cable.
Only electrical circuits that do not pose a contact risk can be connected to the remaining signal
inputs and outputs.

Safety
D184B140U02 FSM4000 13
1.9 Safety instructions for operation
During operation with hot fluids, contact with the surface may result in burns.
Aggressive fluids may result in corrosion or abrasion of the parts that come into contact with the
medium. As a result, pressurized fluids may escape prematurely.
Wear to the flange gasket or process connection gaskets (e.g., aseptic threaded pipe
connections, Tri-Clamp, etc.) may enable a pressurized medium to escape.
When using internal flat gaskets, these can become embrittled through CIP/SIP processes.
If pressure shocks exceeding the device's permissible nominal pressure occur continuously
during operation, this can have a detrimental effect on the device's service life.
1.10 Technical limit values
The device is designed for use exclusively within the stated values on the name plate and within
the technical limit values specified in the data sheets.
The following technical limit values must be observed:
• The permissible operating pressure (PS) in the permissible temperature (TS) may not
exceed the pressure-temperature ratings.
• The maximum operating temperature may not be exceeded.
• The permitted operating temperature may not be exceeded.
• The housing protection system must be observed.
• The flowmeter sensor may not be operated in the vicinity of powerful electromagnetic fields,
e.g., motors, pumps, transformers, etc. A minimum spacing of approx. 1 m (3.28 ft) should
be maintained. For installation on or to steel parts (e.g., steel brackets), a minimum spacing
of approx. 100 mm (3.94 inch) should be maintained (based on IEC801-2 and IECTC77B).
1.11 Allowed Fluids
When measuring fluids, the following points must be observed:
• Fluids may only be used if, based on state-of-the-art technology or the operating experience
of the user, it is assured that chemical and physical properties of the components coming
into contact with the fluids (signal electrodes, ground electrodes, liners and, possibly,
process connections, protective plates or protective flanges) are not affected during the
operating life.
• Fluids with unknown properties or abrasive fluids may only be used if the operator can
perform regular and suitable tests to ensure the safe condition of the device.
• Observe the information on the name plate.

Safety
14 FSM4000 D184B140U02
1.12 Maintenance and inspection safety information
Warning – Risk to persons!
When the housing cover is open, EMC and protection against contact are suspended. There
are electric circuits within the housing which pose a contact risk.
The auxiliar
y
power must be switched off before openin
g
the housin
g
cover.
Warning – Risk to persons!
The inspection screw (for draining condensate fluid) for devices ≥DN 350 can be under
pressure. The fluid which spurts out can cause severe injuries.
Depressurize pipes before openin
g
the inspection screw.
Corrective maintenance work may only be performed by trained personnel.
• Depressurize the device and adjoining lines or containers before removing the device.
• Check whether hazardous materials are used as materials to be measured before opening
the device. Residual amounts of hazardous material may still be present in the device and
could escape when the device is opened.
• As far as provided in the scope of the operational responsibility, check the following items
through a regular inspection:
 the pressure-carrying walls / lining of the pressure device
 the measurement-related function
 the leak tightness
 the wear (corrosion)
1.13 Returning devices
Use the original packaging or suitably secure shipping containers if you need to return the
device for repair or recalibration purposes. Fill out the return form (see the Appendix) and
include this with the device.
According to EC guidelines for hazardous materials, the owner of hazardous waste is
responsible for its disposal or must observe the following regulations for shipping purposes:
All devices delivered to ABB Automation Products GmbH must be free from any hazardous
materials (acids, alkalis, solvents, etc.).
Rinse out and neutralize hazardous materials from all hollow spaces such as between meter
tube and housing. For flowmeter sensors with a nominal diameter larger than DN 350, the
service screw (for draining condensate fluid) at the lower point of the housing must be opened
to dispose of hazardous substances and to neutralize the coil and electrode chamber. These
activities must be confirmed in writing using the return form.
Please
Please contact Customer Center Service acc. to page 2 for nearest service location.

Safety
D184B140U02 FSM4000 15
1.14 Integrated management system
ABB Automation Products GmbH operates an integrated management system, consisting of:
• Quality management system to ISO 9001
• Environmental management system to ISO 14001
• Occupational health and safety management system to BS OHSAS 18001 and
• Data and information protection management system
Environmental awareness is an important part of our company policy.
Our products and solutions are intended to have a minimal impact on the environment and on
people during manufacturing, storage, transport, use, and disposal.
This includes the environmentally-friendly use of natural resources. We conducts an open
dialog with the public through our publications.
1.15 Disposal
This product is manufactured from materials that can be reused by specialist recycling
companies.
1.15.1 Information on WEEE Directive 2012/19/EU (Waste Electrical and Electronic Equipment)
This product is not subject to WEEE Directive 2012/19/EU or relevant national laws
(e.g., ElektroG in Germany).
The product must be disposed of at a specialist recycling facility. Do not use municipal garbage
collection points. According to the WEEE Directive 2012/19/EU, only products used in private
applications may be disposed of at municipal garbage facilities. Proper disposal prevents
negative effects on people and the environment, and supports the reuse of valuable raw
materials.
If it is not possible to dispose of old equipment properly, ABB Service can accept and dispose of
returns for a fee.

Design and function
16 FSM4000 D184B140U02
2 Design and function
2.1 Measuring principle
Measurements performed by the electromagnetic flowmeter are based on Faraday’s law of
induction. A voltage is generated in a conductor when it moves through a magnetic field.
This principle is applied to a conductive fluid in the measuring tube through which a magnetic
field is generated perpendicular to the flow direction (see schematic).
The voltage induced in the fluid is measured by two electrodes located diametrically opposite
each other. This signal voltage UEis proportional to the magnetic induction B, the electrode
spacing D and the average flow velocity v.
Considering that the magnetic induction B and the electrode spacing D are constant values, a
proportionality exists between the signal voltage UEand the average flow velocity v. From the
equation for calculating the volume flowrate, it follows that the signal voltage is linearly
proportional to the volume flowrate: UE~ qv.
The induced voltage is converted by the transmitter to standardized, analog and digital signals.
G00005
1
2
3
Fig. 6: Electromagnetic flowmeter schematic
1Magnet coil
2Measuring tube in electrode plane
3Signal electrode
UESignal voltage
BMagnetic induction
DElectrode spacing
vAverage flow velocity
qvVolume flow
UE~ vDB 
qv = v
D
4
2

UE~ qv

Design and function
D184B140U02 FSM4000 17
2.2 Design
An electromagnetic flowmeter system consists of a flowmeter sensor and a transmitter. The
flowmeter sensor (model SE41F, SE21W, SE21F, SE21) is installed in the specified pipeline
while the transmitter (S4) is mounted locally or at a central location.
2.3 Device designs
The µP transmitter is mounted at a separate location from the flowmeter sensor. Up to 50 m
cable length for a minimum conductivity of 20 µS/cm. For flowmeters with preamplifiers, the
signal length is increased to 200 m. The electrical connection between the transmitter and the
flowmeter sensor is provided by a signal cable and a magnet coil cable in the terminal box.
Fig. 7
The transmitter is available in the design:
• Field housing unit model S4
The flowmeter sensor comes with aluminum or stainless steel housing:
• Aluminum housing: Model FSM4000-SE41F
• Stainless steel housing: Model FSM4000 SE21W / SE21F / SE21
Important
Also older model flowmeters sensor can be connected to S4 transmitters. For additional
information, see chapter "6.1 Preliminary checks prior to start-up" or "11 Operating S4 with an
older sensor".

Transport
18 FSM4000 D184B140U02
3 Transport
3.1 Inspection
Check the devices for possible damage that may have occurred during transport. Damages in
transit must be recorded on the transport documents. All claims for damages must be claimed
without delay against the shipper and before the installation.
3.2 General information on transport
Observe the following when transporting the device to the measurement site:
• The center of gravity may not be in the center of the device.
• The protective plates or dust caps mounted at the process connections of devices equipped
with PTFE/PFA may only be removed before installation. To prevent possible leakage, make
sure that the liner is not cut or damaged.
• Flanged units may not be lifted by the transmitter housing or terminal box.
3.3 Transport of flanged units up to nominal diameter DN 300
Warning – Danger of injuries due to slipping meter.
The center of gravity of the complete meter may be higher than the lifting straps.
Make sure the device has not rotated or slipped unintentionally during transport. Support the
meter laterall
y
.
Lifting straps must be used to transport flanged units up to a nominal diameter of DN 300. Wrap
the straps around both process connections when lifting the meter. Chains should not be used,
since these may damage the housing.
G00587-01
Fig. 8: Transport of flanged units up to nominal diameter DN 300

Transport
D184B140U02 FSM4000 19
3.4 Transport of flanged units larger than nominal diameter DN 350
Notice - Potential damage to parts!
Use of a forklift to transport the device can dent the housing and damage the internal magnet
coils.
Flan
g
ed units must not be lifted b
y
the center of the housin
g
when usin
g
a forklift for transport.
Flanged units must not be lifted by the terminal box or by the center of the housing. Only the
eyebolts fitted to the meter must be used to lift the meter and set it down in the pipeline.
G00461
Fig. 9: Transport of flanged units larger than nominal diameter DN 350

Mounting
20 FSM4000 D184B140U02
4 Mounting
4.1 General information on installation
The following points must be observed for the installation:
• The flow direction must correspond to the identification if present.
• The maximum torque for all flange connections must be complied with.
• The devices must be installed without mechanical tension (torsion, bending).
• Install flange and wafer units with coplanar counter flanges and use only appropriate
gaskets.
• Use only gaskets made from a compatible material for the fluid and fluid temperature or use
only gasket material compatible with hygienic designs.
• Gaskets must not extend into the flow area since possible turbulence could influence the
device accuracy.
• The pipeline may not exert any unallowable forces or torques on the device.
• Do not remove the plugs in the cable connectors until you are ready to install the electrical
cable.
• Make sure the gaskets for the housing cover are seated properly. Carefully seal the cover.
Tighten the cover fittings.
• Install the separate transmitter at a largely vibration-free location.
• Do not expose the transmitter to direct sunlight. Provide appropriate sun protection as
necessary.
4.2 Supports for nominal diameters larger than DN 350
Notice - Potential damage to parts!
Improper support for the device may result in deformed housing and damage to internal
magnet coils.
Place the supports at the ed
g
e of the housin
g
(
see arrows in the fi
g
ure
)
.
Devices with a nominal diameter larger than DN 350 must be mounted with support on a
sufficiently strong foundation.
G00462
Fig. 10: Support for nominal diameters larger than DN 350