ABB TTF200 User manual

—
ABB MEASUREMENT & ANALYTICS | OPERATING INSTRUCTION
TTF200
Field-mount temperature transmitter
—
ABB Limited
Measurement & Analytics
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: [phone]
Fax: [phone]
Email: [e-mail]
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
abb.com/temperature
ABB Inc.
Measurement & Analytics
125 E. County Line Road
Warminster, PA 18974
USA
Tel: [phone]
Fax: [phone]
Temperature transmitter for HART
protocol.
Suitable for all standard
requirements
Measurement made easy
OI/TTF200-EN Rev. B 11.2018
—
TTF200 Introduction
The TTF200 with the 4 to 20 mA output and HART
communications protocol has global approvals
for explosion protection up to Zone 0.
Safety-relevant applications up to SIL 3
(redundant) are supported in accordance with
IEC 61508.
The TTF200 features a universal sensor input for
resistance thermometer, thermocouples,
resistance- and voltage measurement.
Additional Information
Additional documentation on TTF200 is available for
download free of charge at
www.abb.com/temperature.
Alternatively simply scan this code:
—
We reserve the right to make technical changes or modify the contents of this document
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole
or in parts – is forbidden without prior written consent of ABB.
© ABB 2018 3KXT221201R4201

2 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
Table of contents
Change from one to two columns
1Safety.......................................................................... 3
General information and instructions.................................. 3
Warnings.................................................................................... 3
Intended use .............................................................................4
Improper use.............................................................................4
Warranty provisions.................................................................4
Notes on data safety ...............................................................4
Manufacturer’s address..........................................................4
2Use in potentially explosive atmospheres in
accordance with ATEX and IECEx ............................ 5
Ex marking.................................................................................5
Transmitter ..........................................................................5
LCD indicator .......................................................................5
Temperature data ....................................................................6
Transmitter ..........................................................................6
LCD indicator .......................................................................6
Electrical data ...........................................................................6
Transmitter ..........................................................................6
LCD indicator ....................................................................... 7
Installation instructions.......................................................... 7
ATEX / IECEx ........................................................................ 7
Cable entries ........................................................................ 7
Electrical connections .............................................................9
Grounding.............................................................................9
Intrinsic safety installation check ....................................9
Installation in a potentially explosive atmosphere .......9
Commissioning....................................................................... 12
Operating instructions.......................................................... 12
Damage to the ‘Flameproof (enclosure)– Ex d’ type of
protection........................................................................... 12
Protection against electrostatic discharges................ 12
Repair ....................................................................................... 12
3Design and function ................................................ 13
General ..................................................................................... 13
4Product identification ............................................ 13
Name plate .............................................................................. 13
5Transport and storage............................................ 15
Inspection................................................................................ 15
Transporting the device........................................................ 15
Storing the device .................................................................. 15
Ambient conditions .......................................................... 15
Returning devices................................................................... 15
6Installation ............................................................... 15
Opening and closing the housing .......................................16
Rotating the LCD indicator ..................................................16
7Electrical connections .............................................17
Safety instructions .................................................................17
Protection of the transmitter from damage caused by
highly energetic electrical interferences ............................17
Suited protective measures............................................ 18
Conductor material ............................................................... 18
Power supply cable........................................................... 18
Cable glands ........................................................................... 18
Shielding of the sensor connection cable ......................... 18
Examples of shielding / grounding............................... 19
Pin assignment........................................................................21
Terminal for sensor connection cable ............................... 22
Electrical data for inputs and outputs............................... 22
Input - resistance thermometer / resistances ............ 22
Input - thermocouples / voltages.................................. 23
Output................................................................................. 23
Power supply ..................................................................... 24
8Commissioning ........................................................25
General..................................................................................... 25
Checks prior to commissioning .......................................... 25
Communication ..................................................................... 25
Parameterization of the device........................................... 26
Parameter descriptions................................................... 27
Factory settings................................................................ 29
Basic Setup ............................................................................. 30
Sensor error adjustment (DTM adjustment function)
.............................................................................................. 30
HART variables....................................................................31
Communication / HART TAG / device addressing ......31
9Operation..................................................................31
Safety instructions .................................................................31
Process display .......................................................................31
Error messages on the LCD display .............................. 32
10Diagnosis / error messages ...................................32
Messages via the HART interface ....................................... 32
Error message on the LCD display ..................................... 32
Error message on the current output ................................ 32
Possible error messages – HART® ...................................... 33
11Maintenance ............................................................ 34
Safety instructions ................................................................ 34
Cleaning................................................................................... 34
12Repair ....................................................................... 34
Safety instructions ................................................................ 34
Returning devices .................................................................. 34
13Recycling and disposal............................................35
14Specification ............................................................35
15Additional documents.............................................35
16Appendix .................................................................. 36
Return form............................................................................. 36

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 3
1Safety
General information and instructions
These instructions are an important part of the product and
must be retained for future reference.
Installation, commissioning, and maintenance of the product
may only be performed by trained specialist personnel who have
been authorized by the plant operator accordingly. The specialist
personnel must have read and understood the manual and must
comply with its instructions.
For additional information or if specific problems occur that are
not discussed in these instructions, contact the manufacturer.
The content of these instructions is neither part of nor an
amendment to any previous or existing agreement, promise or
legal relationship.
Modifications and repairs to the product may only be performed
if expressly permitted by these instructions.
Information and symbols on the product must be observed.
These may not be removed and must be fully legible at all times.
The operating company must strictly observe the applicable
national regulations relating to the installation, function testing,
repair and maintenance of electrical products.
Warnings
The warnings in these instructions are structured as follows:
DANGER
The signal word ‘DANGER’ indicates an imminent danger.
Failure to observe this information will result in death or
severe injury.
WARNING
The signal word ‘WARNING’ indicates an imminent danger.
Failure to observe this information may result in death or
severe injury.
CAUTION
The signal word ‘CAUTION’ indicates an imminent danger.
Failure to observe this information may result in minor or
moderate injury.
NOTICE
The signal word
‘
NOTIC
E
’
indicates possible material damage.
Note
‘Note’ indicates useful or important information about the
product.

4 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 1 Safety
Intended use
This device is intended for the following uses:
• To measure the temperature of fluid, pulpy or pasty
substances and gases or resistance/voltage values.
The device has been designed for use exclusively within the
technical limit values indicated on the name plate and in the data
sheets.
• The maximum ambient temperature must not be exceeded.
• The IP rating of the housing must be observed during
operation.
• For use in potentially explosive atmospheres, follow the
associated guidelines.
• When using as a SIL-device in safety-relevant applications,
the SIL Safety Manual should be observed.
Improper use
The following are considered to be instances of especially
improper use of the device:
• For use as a climbing aid, for example for mounting
purposes.
• For use as a bracket for external loads, for example as a
support for piping, etc.
• Material application, for example by painting over the
housing, name plate or welding/soldering on parts.
• Material removal, for example by spot drilling the
housing.
Warranty provisions
Using the device in a manner that does not fall within the scope
of its intended use, disregarding this manual, using
underqualified personnel, or making unauthorized alterations
releases the manufacturer from liability for any resulting
damage. This renders the manufacturer's warranty null and void.
Notes on data safety
This product is designed to be connected to and to
communicate information and data via a network interface.
It is operator’s sole responsibility to provide and continuously
ensure a secure connection between the product and your
network or any other network (as the case may be).
Operator shall establish and maintain any appropriate measures
(such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data,
installation of anti-virus programs, etc.) to protect the product,
the network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and / or theft of data or information.
ABB Automation Products GmbH and its affiliates are not liable
for damages and / or losses related to such security breaches,
any unauthorized access, interference, intrusion, leakage and /
or theft of data or information.
Manufacturer’s address
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
Customer service center
Tel: [phone]
Email: [email protected]
Change from tw o to one column

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 5
2Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Change from one to two columns
Note
• Further information on the approval of devices for use in
potentially explosive atmospheres can be found in the
explosion protection test certificates (at
www.abb.com/temperature).
• Depending on the design, a specific marking in accordance
with ATEX or IECEx applies.
• In devices with combined types of protection, for example
TTF200-E4, observe the ‘Product Identification’ chapter in
the operating or commissioning instruction before
commissioning.
Ex marking
Transmitter
ATEX intrinsic safety
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 0, 1 and 2.
Model TTF200-E1
Type Examination Test Certificate PTB 05 ATEX 2017 X
II 1 G Ex ia IIC T6 Ga
II 2 (1) G Ex [ia IIC Ga] ib IIC T6 Gb
II 2 G (1D) Ex [ia IIIC Da] ib IIC T6 Gb
ATEX flameproof (enclosure)
Approved for use in Zone 1 and 2.
Model TTF200-E3
Type Examination Test Certificate PTB 99 ATEX 1144 X
II 2G Ex db IIC T6/T4 Gb
ATEX flameproof (enclosure) and intrinsic safety
Approved for use in Zone 1 and 2, in case of intrinsic safety also
for use in Zone 0.
The ‘E4’ coding combines the following types of protection:
‘Intrinsic safety’, (TTF200-E1) and ‘Flameproof (enclosure)’,
(TTF200-E3). Devices with combined types of protection may
only be operated in one of the possible types of protection.
For this purpose, observe the ‘Product Identification’ chapter in
the operating or commissioning instruction before
commissioning.
Model TTF200-E4
Type Examination Test Certificate PTB 99 ATEX 1144 X
PTB 05 ATEX 2017 X
II 2G Ex db IIC T6/T4 Gb
II 1G Ex ia IIC T6 Ga
IECEx intrinsic safety
Approved for use in Zone 0, 1, and 2.
Model TTF200-H1
IECEx certificate of conformity IECEx PTB 09.0014X
Ex ia IIC T6...T1 Ga
Ex [ia IIC Ga] ib IIC T6...T1 Gb
Ex [ia IIIC Da] ib IIC T6...T1 Gb
IECEx flameproof (enclosure)
Approved for use in Zone 1 and 2.
Model TTF200-H5
IECEx certificate of conformity IECEx PTB 12.0039 X
Ex db IIC T6/T4 Gb
LCD indicator
ATEX intrinsic safety
The device fulfills the requirements of Directive 2014/34/EU in
case of corresponding purchase orders and is approved for use
in Zone 0, 1 and 2.
Type Examination Test Certificate PTB 05 ATEX 2079 X
II 1G Ex ia IIC T6 Ga
IECEx intrinsic safety
Approved for use in Zone 0, 1, and 2.
IECEx certificate of conformity IECEx PTB 12.0028X
Ex ia IIC T6

6 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Temperature data
Transmitter
ATEX / IECEx intrinsic safety
Temperature class Permissible ambient temperature range
Device category 1 use Device category 2 / 3 use
T6 −40 to 44 °C
(−40 to 111.2 °F)
−40 to 56 °C
(−40 to 132.8 °F)
T4-T1 −40 to 60 °C
(−40 to 140.0 °F)
−40 to 85 °C
(−40 to 185.0 °F)
ATEX / IECEx Flameproof (Enclosure)
Temperature class Permissible ambient temperature range on the
connection head
T6 −40 to 67 °C (−40 to 152 °F)
T4 to T1 −40 to 85 °C (−40 to 185 °F)
LCD indicator
ATEX / IECEx intrinsic safety
Temperature class Permissible ambient temperature range
Device category 1 use Device category 2 / 3 use
T6 −40 to 44 °C
(−40 to 111.2 °F)
−40 to 56 °C
(−40 to 132.8 °F)
T4-T1 −40 to 60 °C
(−40 to 140 °F)
−40 to 85 °C
(−40 to 185 °F)
Electrical data
Transmitter
Intrinsic safety type of protection Ex ia IIC (Part 1)
Supply circuit
Max. voltage Ui= 30 V
Short-circuit current Ii= 130 mA
Max. power Pi= 0.8 W
Internal inductance Li= 160 µH
Internal capacitance Ci= 0.57 nF
Intrinsic safety type of protection Ex ia IIC (Part 2)
Measurement current circuit
Resistance
thermometers,
resistors
Thermocouples, voltages
Max. voltage Uo= 6.5 V
Uo= 1.2 V
Short-circuit current Io= 17.8 mA
Io= 50 mA
Max. power Po= 29 mW
Po= 60 mW
Internal inductance Li= 0 mH
Li= 0 mH
Internal capacitance Ci= 118 nF
Ci= 118 nF
Maximum permissible
external inductance
Lo= 5 mH
Lo= 5 mH
Maximum permissible
external capacitance
Co= 1.55 μF
Co= 1.05 μF
Intrinsic safety type of protection Ex ia IIC (Part 3)
LCD indicator interface
Max. voltage Uo= 6.2 V
Short-circuit current Io= 65.2 mA
Max. power Po= 101 mW
Internal inductance Li= 0 mH
Internal capacitance Ci= 0 nF
Maximum permissible
external inductance
Lo= 5 mH
Maximum permissible
external capacitance
Co= 1.4 μF

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 7
Type of protection flameproof (enclosure) Ex db IIC
Supply circuit
Maximum voltage US= 30 V
Maximum current Is= 32 mA, limited by the upstream fuse
(rated fuse current 32 mA)
Measurement current
circuit
Maximum voltage UO= 6.5 V
Maximum current IO= 17.8 mA
Maximum power PO= 29 mW
LCD indicator
Intrinsic safety type of protection Ex ia IIC
Supply circuit
Max. voltage Ui= 9 V
Short-circuit current Ii= 65.2 mA
Max. power Pi= 101 mW
Internal inductance Li= 0 mH
Internal capacitance Ci= 0 nF
Installation instructions
ATEX / IECEx
The installation, commissioning, maintenance and repair of
devices in potentially explosive atmospheres must only be
carried out by appropriately trained personnel. Works may be
carried out only by persons, whose training has included
instructions on different types of protection and installation
techniques, concerned rules and regulations as well as general
principles of zoning. The person must possess the appropriate
competences for the type of work to be conducted.
When operating with combustible dusts, comply with
EN 60079-31.
The safety instructions for electrical apparatus in potentially
explosive areas must be in accordance with Directive
2014/34/EU (ATEX) and IEC 60079-14 (Installation of electrical
equipment in potentially explosive areas).
Comply with the applicable regulations for the protection of
employees to ensure safe operation.
Cable entries
Devices with type of protection ‘Ex d’ without supplied
cable glands
For devices with type of protection ‘Ex d – flameproof
(enclosure)’ supplied without cable glands, refer to the notices in
ATEX - Zone 1 (20) on page 10 and Flameproof (enclosure) -
Zone 1 on page 11.
For information on the cable gland used, refer to the relevant
data sheet and operating instructions.
Devices with type of protection ‘Ex d’ with cable glands
If devices in ‘Ex d – flameproof (enclosure)’ type of protection
with cable gland are ordered, an Ex d certified cable gland is
factory-installed.
Cable gland data
• Thread: 2 × M20 × 1.5 or 2 × ½ in NPT
• Temperature range: −50 to 85 °C (−58 to 185 °F)
• Cable outside diameter: 3.2 to 8.7 mm (0.13 to 0.34 in)
• Material: nickel-plated brass
The cable entry is only suitable for fixed installations and non-
reinforced cables with round and smooth plastic sleeves and
suitable outside diameter. The cables must be attached
appropriately in order to prevent them being pulled out or
twisted.
The operating instruction and approvals supplied with the cable
glands, as well as any applicable requirements in accordance
with EN 60079-14 must be taken into account accordingly.

8 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Installation instructions for cable glands
The sealing rings of the cable glands harden at low
temperatures. Before installation, bring the sealing rings to a
temperature of at least 20 °C for 24 hours. Before inserting the
sealing rings and fixing them onto the cable gland, knead the
rings to ensure they are soft and flexible.
IP rating IP66 / 67 is only achieved by installing the black
neoprene sealing ring between the cable gland and the housing
and by observing the tightening torque of 3.6 Nm (Figure 2,
item 2).
Cables must be protected against extreme mechanical loads
(caused by tension, torsion, crushing, and so on). Even under
operating conditions, it must be ensured that the cable entry
remains hermetically sealed. The customer must provide a strain
relief device for the cable.
A10229
Ø
A
B
C
A40 mm
B12 mm
CØ8.5 / 12 mm
Figure 1: Stripping the connection cable
1.Check that cable used is suitable (i.e., check the mechanical
resilience, temperature range, creep resistance, resistance to
chemicals, outside diameter, and so on).
2.Strip the cable in accordance with Figure 1.
3.Check the outer sleeve for damage and soiling.
4.Insert the cable in the cable gland.
A10230
21
Figure 2: Tighten cable glands
5.Tighten the cable gland until the cable is firmly enclosed by
the sealing ring (Figure 2, item 1). Do not tighten more than
1.5--times of the specified torque on the housing (see
assembly instructions for cable gland)!
Maintenance
Check the cable glands during each maintenance session. If the
cable is slack, retighten the cap(s) of the cable glands.
If it is not possible to retighten them, the cable gland will need
to be replaced.
M20 × 1.5 plastic cable gland for various types of protection
The optionally supplied M20 × 1.5 plastic cable gland has a
limited temperature range. The permissible ambient
temperature range of the cable gland is −20 to 80 °C
(−4 to 176 °F). When using the cable gland, make sure that the
ambient temperature is within this range.
The cable gland must be installed in the housing with a
tightening torque of 3.8 Nm. On the cable side, when installing
the connection of the cable gland and cable, check for integrity
to ensure that the required IP rating is met.

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 9
Electrical connections
Grounding
If, for functional reasons, the intrinsically safe circuit needs to be
grounded by means of a connection to the potential
equalization, it may only be grounded at one point.
Intrinsic safety installation check
If transmitters are operated in an intrinsically safe circuit, proof
that the interconnection is intrinsically safe must be provided in
accordance with IEC/EN 60079-14 as well as IEC/EN 60079-25.
The supply isolators / DCS inputs must feature intrinsically safe
input protection circuits in order to eliminate hazards (spark
formation).
In order to provide proof of intrinsic safety, the electrical limit
value must be used as the basis for the EC-type examination
certificates for the equipment (devices); this includes the
capacitance and inductance values of the cables.
Proof of intrinsic safety is said to have been provided if the
following conditions are fulfilled when a comparison is carried
out in relation to the limit values of the equipment:
Transmitter
(intrinsically safe equipment)
Supply isolator / DCS input
(related equipment)
Ui≥U
o
Ii≥I
o
Pi≥P
o
Li+ Lc(cable) ≤L
o
Ci+ Cc(cable) ≤C
o
Field (Ex area) Control room (safe area)
A10096
AB
+
-
+
-
ATransmitter BSupply isolator / DCS input with
supply / segment coupler
Figure 3: Intrinsic safety installation check
Installation in a potentially explosive atmosphere
Transmitters can be installed in all kinds of industrial sectors.
Potentially explosive systems are divided into zones,
meaning that a wide range of different instruments are also
required. For this, pay attention to the country-specific
guidelines and certificates!
Note
Ex relevant specifications must be taken from the EC-type
examination certificates and other relevant certificates that
apply in each case.
ATEX - Zone 0
Designation: II 1 G Ex ia IIC T6 Ga
Ex area Zone 0 Safe area
A11227
ia
ia
J
D
ia
A
CB
ASensor
BTTF200 transmitter
CSupply isolator [Ex ia]
DInterface for LCD indicator
Figure 4: Hookup in ATEX – Zone 0
The input for the supply isolator must be designed with ‘Ex ia’
type of protection.
When using the transmitter in Zone 0, make sure that
impermissible electrostatic charging of the transmitter is
avoided (observe the warnings on the device).
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards.
WARNING
Risk of explosion!
When using the device in areas that require the device safety
level EPL ‘Ga’ (Zone 0), the TTF200 types must be installed
with aluminum housings, protected against strong
mechanical impacts or friction.
Note
When operating the transmitter in Zone 0 (EPL ‘Ga’), the
compatibility of the device materials with the surrounding
atmosphere must be ensured.
Encapsulation material used for the transmitter:
Polyurethane (PUR), WEVO PU-417

10 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
… Electrical connections
ATEX - Zone 1 (0)
Marking: II 2 (1) G Ex [ia IIC Ga] ib IIC T6 Gb
Zone 0 or 1 Ex area Zone 1 Safe area
A10127
ib
ia
J
ia
D
A
CB
ASensor
BTTF200 transmitter
CSupply isolator [Ex ib]
DInterface for LCD indicator
Figure 5: Hookup in ATEX - Zone 1 (0)
The input for the supply isolator must be designed with ‘Ex ib’
type of protection.
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards.
The sensor can be installed in Zone 1 or Zone 0.
When using the transmitter in Zone 1, you must ensure that
impermissible electrostatic charging of the temperature
transmitter is prevented (observe the warnings on the device).
ATEX - Zone 1 (20)
Marking: II 2 G (1D) Ex [ia IIIC Da] ib IIC T6 Gb
Zone 20 or 21 Ex area Zone 1 Safe area
A10128
ib
ib
J
D
ia
ia
CB
A
ASensor
BTTF200 transmitter
CSupply isolator [Ex ib]
DInterface for LCD indicator
Figure 6: Hookup in ATEX - Zone 1 (20)
The input for the supply isolator must be designed with ‘Ex ib’
type of protection.
As the user, it is your responsibility to ensure that the sensor
instrumentation meets the requirements of applicable explosion
protection standards.
The sensor can be installed in Zone 20 or Zone 21.
When using the transmitter in Zone 1, make sure that
impermissible electrostatic charging of the temperature
transmitter is avoided (observe the warnings on the device).

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 11
Flameproof (enclosure) - Zone 1
Housing design: ATEX II 2G Ex db IIC T6/T4 Gb
Ex area Zone 1 Safe area
A10130
J
CB
E
D
A
ASensor
BTransmitter in Ex d-housing
CSupply isolator with voltage limit
(30 V)
DFuse, 32 mA
EInterface for LCD indicator
Figure 7: Hookup in Zone 1 ‘flameproof (enclosure)’ type of protection
The power supply circuit of the transmitter must be limited by
an upstream fuse with a fuse current rating of 32 mA.
Maximum input terminal voltage of the transmitter: 30 V DC
The ‘flameproof enclosure’ type of protection is only achieved by
correctly installing a specially certified cable gland with the Ex d
type of protection with the corresponding marking.
The sensor instrumentation must be provided by the user in
accordance with the valid Ex-standards.
As far as the installation and mounting of components is
concerned (explosion-proof cable entries, connection parts),
only those components are approved which at the least
technically comply with the current version of the
PTB 99 ATEX 1144 X type examination certificate and for which a
separate examination certificate exists. At the same time, it is
imperative that the operating conditions listed in the respective
component certificates are complied with.
The transmitter must be connected using suitable cable and
cable entries or pipeline systems that satisfy the requirements
of EN 60079-1 and for which a separate examination certificate
exists. If the transmitter is connected to pipeline systems, the
relevant sealing device must be affixed directly to the housing.
Cable entries (PG glands) and sealing plugs of simple design
must not be used.
Close unused cable entry in accordance with EN 60079.-1.
The connection lead must be routed securely and in such a way
as to ensure adequate protection against damage.
If the temperature on the entry parts is over 70° C, connection
leads with sufficient temperature resistance must be used.
The transmitter must be integrated into the local potential
equalization of the potentially explosive area.

12 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 2 Use in potentially explosive atmospheres in accordance with
ATEX and IECEx
Commissioning
The commissioning and parameterization of the device may also
be carried out in potentially explosive atmospheres using a
handheld terminal that has been approved accordingly under
consideration of an intrinsic safety installation check.
Alternatively, an Ex modem can be connected to the circuit
outside the potentially explosive atmosphere.
Operating instructions
DANGER
Risk of explosion due to hot parts
Hot parts inside the device pose an explosion hazard.
• Never open the device immediately after switch-off.
• A waiting time of at least four minutes should be observed
before opening the device.
DANGER
Explosion hazard when opening the device
Explosion hazard when opening the device with activated
power supply.
• Before opening the device, switch off the power supply.
Damage to the ‘Flameproof (enclosure)– Ex d’ type of
protection
The cover thread is used as a flameproof joint for the
‘Flameproof (enclosure) – Ex d’ type of protection.
• During assembly / disassembly of the device, make sure that
the cover thread does not get damaged.
• Devices with damaged threads must no longer be used in
potentially explosive atmospheres.
Protection against electrostatic discharges
The painted surface of the housing and the plastic parts inside
the device can store electrostatic charges.
WARNING
Risk of explosion!
The device must not be used in areas in which process-related
electrostatic charging of the housing may occur.
• The device must be maintained and cleaned so that any
dangerous electrostatic charge is avoided.
Repair
DANGER
Explosion hazard
Explosion hazard due to improper repair of the device. Faulty
devices must not be repaired by the operator.
• Any repair may only be performed in the production plant
or by workshops authorized by ABB.
• Repairs on flameproof joints are not permitted.

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 13
3Design and function
General
TTF200 digital transmitters are communication-ready devices
with microprocessor-controlled electronics.
For bidirectional communication, the 4 to 20 mA output signal is
superimposed with an FSK signal in accordance with the HART
standard.
The transmitters can be configured, polled, and tested using a
DTM, an EDD or using the Field Information Manager (FIM).
Handheld terminals can also be used for communication
purposes.
As an option, the transmitter can be fitted with the type BS LCD
indicator. The LCD indicator is used to visualize the current
process values.
Note
A configuration of the TTF200 with the type B LCD indicator with
the configuration function used in the TTF300 is not possible.
1Supply voltage cable
2TTF200 transmitter
3Temperature sensor
4Process pipe
5Sensor connection cable
Figure 8: Setup of the TTF200
4Product identification
Name plate
Note
Products that are marked with the adjacent symbol
may not be disposed of as unsorted municipal waste
(domestic waste).
They should be disposed of through separate
collection of electric and electronic devices.
Note
The ambient temperature range specified on the name plate
refers only to the transmitter itself and not to the measuring
element used in the measuring inset.
1Manufacturer, manufacturer
address, country of
manufacture, manufacturing
year - week
2Safety integrity level, SIL logo
(optional)
3CE mark (EU conformity), if not
on additional plate
4Type designation / model
5Transmitter communications
protocol (HART)
62D barcode for serial number in
accordance with order
7IP rating of the housing
8Software revision (SW),
hardware revision (HW)
9‘Follow product documentation’
symbol
jClient configuration:
set measuring range of the
transmitter
kClient configuration:
set sensor type and circuit type
lAmbient temperature range, on
additional plate for Ex versions
mTransmitter specification
(supply voltage range, output
current range, communications
protocol)
n7-digit serial number of the
device electronic unit
oDevice order coding:
contains coding of type of
protection, housing/indicator,
cable entry and communications
protocol
pSerial number of the device
(serial number in accordance
with order)
Figure 9: Name plate (example)

14 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 4 Product identification
… Name plate
Explosion protection marking for devices with one type of
protection
Devices with an explosion-proof design are marked with the
following additional plates.
Note
• Further information on the approval of devices for use in
potentially explosive atmospheres can be found in the
explosion protection test certificates (at
www.abb.com/temperature).
• Depending on the design, a specific marking in accordance
with ATEX or IECEx applies.
1Type designation in accordance
with approval
2Approval number
3Protection class of the explosion-
proof design (explosion
protection marking)
4Type designation
5Temperature class of the
explosion-proof design
6CE mark (EU conformity) and
notified body for quality
assurance
7Ex marking
Figure 10: Additional plate for explosion-protected apparatus (example)
Explosion protection marking for devices with a
combination of explosion protection types
Coding of the type of protection of the device in accordance
with order information can also refer to a combination of
different explosion approvals for various types of protection.
1Checkboxes for marking type of protection
Figure 11: Combination of ‘Intrinsic safety’ and ‘Flameproof (enclosure)’ types of
protection, coding of type of protection: E4.
Measures required before the use of devices with combined
types of protection
NOTICE
Note for temperature transmitters with combined approval
Before the transmitter is installed, the selected type of
protection must be permanently marked on the explosion
protection certification plate.
The transmitter can then only be operated with this type of
protection throughout its entire service life.
• If two protection types are indelibly marked on the
explosion protection certification plate, the transmitter
must not be used in areas categorized as hazardous.
Devices with combined types of protection may only be
operated in one of the possible types of protection.
Before commissioning, users must decide on one of these types
of protection and their corresponding approval.
The ‘E4’ coding combines the following types of protection:
‘Intrinsic safety’, type ‘TTF200-E1’ and ‘Flameproof (enclosure)’,
type ’TTF200-E3’.
The additional plate has two selection fields (see Figure 11) for
marking.
It is absolutely necessary to mark one of the selection fields on
the left side indelibly in accordance with the selected type of
protection of the application. This has to be done before the
TTF200 is commissioned in the application.
The marking must be applied in a permanent and indelible
manner, for example using a caustic or acidic pencil or by
stamping on a metallic plate.
Unmarked devices must NOT be commissioned.

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 15
5Transport and storage
Inspection
Check the devices immediately after unpacking for possible
damage that may have occurred from improper transport.
Details of any damage that has occurred in transit must be
recorded on the transport documents.
All claims for damages must be submitted to the shipper
without delay and before installation.
Transporting the device
Observe the following instructions:
• Do not expose the device to humidity during transport.
Pack the device accordingly.
• Pack the device so that it is protected against vibrations
during transport, for example, by using air-cushioned
packing.
Storing the device
Bear the following points in mind when storing devices:
• Store the device in its original packaging in a dry and
dust-free location.
• Observe the permitted ambient conditions for transport
and storage.
• Avoid storing the device in direct sunlight.
• In principle, the devices may be stored for an unlimited
period. However, the warranty conditions stipulated in
the order confirmation of the supplier apply.
Ambient conditions
The ambient conditions for the transport and storage of the
device correspond to the ambient conditions for operation of
the device.
Adhere to the device data sheet!
Returning devices
For the return of devices, follow the instructions in Repair on
page 34.
6Installation
A10268
3
4
1
2
1
2
1Wall / Pipe
2Bracket
3Transmitter
4Locking screw
Figure 12: Installation variants
CAUTION
Risk of injury!
There is a risk of injury if the transmitter falls out due to
improper mounting.
• Make sure that transmitter is securely fastened.
Wall mounting:
Fasten the wall bracket to the wall using 4 screws (Ø 10 mm)
Pipe mounting:
Attach the pipe mount to the pipe using 2 pipe clamps
(Ø 10 mm). The pipe mount can be fastened to a pipe with a
maximum diameter of 63.5 mm (2.5 in)

16 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 6 Installation
Opening and closing the housing
DANGER
Danger of explosion if the device is operated with the
transmitter housing or terminal box open!
While using the device in potentially explosive atmospheres
before opening the transmitter housing or the terminal box,
note the following points:
• A valid fire permit must be present.
• Make sure that no flammable or hazardous atmospheres
are present.
A11167
1
Figure 13: Cover lock (example)
To open the housing, release the cover lock by screwing in the
Allen screw 1.
After closing the housing, lock the housing cover by unscrewing
the Allen screw 1.
NOTICE
Potential adverse effect on the IP rating
• Check the O-ring gasket for damage and replace it if
necessary before closing the housing cover.
• Check that the O-ring gasket is properly seated when
closing the housing cover.
Rotating the LCD indicator
A11168
1
2
1Front view 2Rear view of LCD indicator / plug
positions
Figure 14: LCD indicator
The position of the LCD indicator can be adjusted to suit the
mounting position of the transmitter, to ensure that the display
is as clearly legible as possible. There are 4 positions at
increments of 90°-.
To adjust the position, proceed as follows:
1.Tighten the lock screw under the housing cover.
2.Release the housing cover by turning it counterclockwise.
3.Carefully pull the LCD indicator to release it from its
bracket.
4.Carefully insert the LCD indicator in the required position.
5.Screw the housing cover back on.
6.Loosen the lock screw until the housing cover is firmly in
place.

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 17
7Electrical connections
Safety instructions
DANGER
Explosion hazard
Improper installation and commissioning of the device carries
a risk of explosion.
• For use in potentially explosive atmospheres, observe the
information in Use in potentially explosive atmospheres
in accordance with ATEX and IECEx on page 5!
Observe the following instructions:
• The electrical connection may only be established by
authorized specialist personnel and in accordance with
the connection diagrams.
• The relevant regulations must be observed during electric
installation.
• The electrical connection information in the instruction
must be observed; otherwise, the electric IP rating may
be adversely affected.
• Safe isolation of electric circuits which are dangerous if
touched is ensured only if the connected devices satisfy
the requirements of DIN EN 61140 (VDE 0140 Part 1)
(basic requirements for safe isolation).
• To ensure safe isolation, install connection leads separate
from electric circuits which are dangerous if touched, or
implement additional insulation measures.
• Connections must only be established in a dead-voltage
state!
• The transmitter has no switch-off elements. Therefore,
overcurrent protective devices, lightning protection, or
voltage disconnection options must be provided with the
installation.
• The power supply and signal are routed in the same
conductor and should be implemented as a SELV or PELV
circuit in accordance with the relevant standard
(standard version). For the explosion-proof design, the
guidelines in accordance with the Ex standard must be
adhered to.
• You need to check that the available power supply
corresponds to the information on the name plate.
Note
The signal cable wires must be provided with wire end sleeves.
The slotted screws of the connection terminals are tightened
with a size 1 screwdriver (3.5 or 4 mm).
Protection of the transmitter from damage
caused by highly energetic electrical
interferences
The transmitter has no switch-off elements. Therefore,
overcurrent protective devices, lightning protection, or voltage
disconnection options must be provided at the plant.
For the shielding and grounding of the device and the
connection cable, observe Examples of shielding / grounding on
page 19.
NOTICE
Temperature transmitter damage!
Overvoltage, overcurrent and high-frequency interference
signals on the supply connection as well as sensor connection
side of the device can damage the temperature transmitter.
ADo not weld
BNo high-frequency interference signals / switching operations of large
consumers
CNo overvoltage due to lightning
Figure 15: Warning signs
Overcurrent and overvoltage can occur through for example
welding operations, switching operations of large electric
consumers, or lightning in the vicinity of the transmitter, sensor,
as well as connector cables.
Temperature transmitters are sensitive devices on the sensor
side as well. Long connector cables to the sensor can encourage
damaging interference. This can already happen if temperature
sensors are connected to the transmitter during installation, but
are not yet integrated into the system (no connection to the
supply isolator / DCS)!

18 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 7 Electrical connections
… Protection of the transmitter from
damage caused by highly energetic
electrical interferences
Suited protective measures
The following items should be observed to protect the
transmitter from sensor-side damage:
• In the vicinity of the transmitter, sensor and sensor
connector cable in case of a connected sensor, high-energy
overvoltage, overcurrent and high-frequency interference
signals due to welding operations, lightning, circuit breakers
or large consumers of electricity among others should be
absolutely avoided.
• The connection cable of the sensor on the transmitter should
be disconnected when performing welding work in the
vicinity of the installed transmitter, sensor, as well as supply
lines from the sensor to the transmitter.
• This correspondingly also applies to the supply side, if there
is a connection there.
Conductor material
Power supply cable
Maximum cable outer diameter:
12 mm (0.47 in)
Maximum wire cross section:
2.5 mm2(AWG 16)
Cable glands
The cable diameter must be appropriate for the cable gland used
so that IP rating IP 66 /IP 67 or NEMA 4X can be maintained. This
must be checked during installation.
For delivery without cable gland (thread M20 × 1.5 or NPT ½ in),
the following points must be observed:
• Use cable glands in accordance with version M20 × 1.5 or
NPT ½ in.
• Observe information in the data sheet for the cable gland
used.
• Check the working temperature for the cable gland used.
• Check the IP rating IP 66 / IP 67 or NEMA 4X of the cable
gland used.
• Check the Ex relevant specifications for the cable gland
used in accordance with the manufacturer data sheet or
the Ex declaration.
• The cable gland used must be approved for the cable
diameter (IP rating).
• Observe tightening torque in accordance with
information in data sheet / operating instructions for the
cable gland used.
Shielding of the sensor connection cable
To ensure the system benefits from optimum electromagnetic
interference immunity, the individual system components, and
the connection cables in particular, need to be shielded.
The shield must be connected to the ground reference plane.
Note
National regulations and directives must be observed when
grounding system components.
NOTICE
Damage to components!
In systems without potential equalization or with potential
differences between the individual grounding points, multiple
instances of shield grounding can result in transient currents
at mains frequency.
These can damage the shielding, influence the measurements
and have a significant impact on signal transmission, of bus
signals in particular.
Change from tw o to one column

TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B 19
Examples of shielding / grounding
Insulated sensor measuring inset (thermocouple, mV, RTD, ohms), transmitter housing grounded
The shielding of the sensor connection cable is grounded via the grounded transmitter housing. This shielding is insulated from the
sensor.
The shielding of the power supply cable is grounded at the supply isolator / DCS input directly This shielding is insulated from the
transmitter housing.
The shielding of the power supply cable and the shielding of sensor connection cable must not be connected to one another. Make
sure that the shielding is not connected to ground anywhere else.
A10273
1 2 3 4 6
5
7
9
8
8
1Temperature sensor
2Shielding insulated from sensor
3Sensor connection cable
4Shielding grounded via transmitter housing
5Transmitter housing, grounded
6 Shielding insulated from transmitter housing
7 Supply voltage cable
8Grounding point
9Supply isolator / DCS input
Figure 16: The shieldings of the sensor connection cable and the supply voltage cable are separate and each grounded at one end
Insulated sensor measuring inset (thermocouple, mV, RTD, ohms), transmitter housing grounded
The shielding of the sensor connection cable is grounded via the grounded sensor housing. This shielding of the power supply cable
is insulated from the transmitter housing.
The shielding of the power supply cable is grounded at the supply isolator / DCS input directly This shielding is insulated from the
transmitter housing.
The shielding of the power supply cable and the shielding of sensor connection cable must not be connected to one another. Make
sure that the shielding is not connected to ground anywhere else.
A10274
1 2 3 4 6
5
7
9
8
8
8
1Temperature sensor
2Shielding grounded via sensor
3Sensor connection cable
4Shielding insulated from transmitter housing
5Transmitter housing, grounded
6Shielding insulated from transmitter housing
7Supply voltage cable
8Grounding point
9Supply isolator / DCS input
Figure 17: The shieldings of the sensor connection cable and the supply voltage cable are separate and each grounded at one end

20 TTF200 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF200-EN REV. B
… 7 Electrical connections
… Shielding of the sensor connection cable
Insulated sensor measuring inset (thermocouple, mV, RTD, ohms), transmitter housing not grounded
The shielding of the power supply cable and the shielding of the sensor connection cable are connected to one another via the
transmitter housing. The shielding is grounded at one end of the power supply cable, directly at the supply isolator / DCS input. Make
sure that the shielding is not connected to ground anywhere else.
A10272
1 2 3
5
6
8
7
4
1Temperature sensor
2Shielding insulated from sensor
3Sensor connection cable
4Shielding connected electrically via transmitter housing
5Transmitter housing, not grounded
6Supply voltage cable
7Grounding point
8Supply isolator / DCS-input
Figure 18: The shieldings of the sensor connection cable and the supply voltage cable are connected electrically via the transmitter housing and grounded at one end
Non-insulated sensor measuring inset (thermocouple), transmitter housing grounded
The shielding of the sensor connection cable is grounded via the grounded pressure sensor housing. This shielding of the power
supply cable is insulated from the transmitter housing.
The shielding of the power supply cable is grounded at the supply isolator / DCS input directly This shielding is insulated from the
transmitter housing. The shielding of the power supply cable and the shielding of the sensor connection cable must not be connected
to one another. Make sure that the shielding is not connected to ground anywhere else.
A10274
1 2 3 4 6
5
7
9
8
8
8
1Temperature sensor
2Shielding grounded via sensor
3Sensor connection cable
4Shielding insulated from transmitter housing
5Transmitter housing, grounded
6Shielding insulated from transmitter housing
7Supply voltage cable
8Grounding point
9Supply isolator / DCS input
Figure 19: The shieldings of the sensor connection cable and the supply voltage cable are separate and each grounded at one end