ABB Busch-Watchdog 6747-500 AGM Series User manual

1473-1-8136 │Rev. 01 │11.2012
Operating Instructions
Busch-Wächter®
Pos: 2 /#Neustruktur#/ Online-Dokumentati on (+KNX)/Titelbl ätter/Waechter /Titelblatt - 6747 WaveLI NE @ 28\mod_1347265067099_ 15.docx @ 232467 @ @ 1
6747-500 AGM-…
220 WaveLINE
=== Ende der Liste für TextmarkeCover = ==

Operating Instructions
Busch-Wächter®
Operating Instructions | 1473-1-8136 — 2 —
Pos: 4 /#Neustruktur#/ Online-Dokumentati on (+KNX)/Inhalts verzeichnis (- -> Für alle Dokumente <-- )/Inhaltsverzeichni s @ 19\mod_1320649044386_ 15.docx @ 109653 @ @ 1
1Safety....................................................................................................................................................................... 3
2Intended use ............................................................................................................................................................ 3
3Environment............................................................................................................................................................. 3
4Setup and function................................................................................................................................................... 4
4.1 Features of function and equipment........................................................................................................ 4
4.2 Detection ranges..................................................................................................................................... 5
4.2.1 Overview of the detection ranges............................................................................................................ 5
4.2.2 Infrared range ......................................................................................................................................... 5
4.2.3 Limitation of the detection range ............................................................................................................. 5
4.3 Radio transmission coverage.................................................................................................................. 6
5Technical data.......................................................................................................................................................... 7
6Installation and electrical connection ....................................................................................................................... 8
6.1 Requirements for the electrician ............................................................................................................. 8
6.2 Mounting ................................................................................................................................................. 9
6.2.1 Installation sites ...................................................................................................................................... 9
6.2.2 Preparing the installation....................................................................................................................... 10
6.2.3 Mounting steps...................................................................................................................................... 11
7Commissioning ...................................................................................................................................................... 13
7.1 Setting / limiting the coverage and the detection range......................................................................... 13
7.2 Activation test........................................................................................................................................ 14
8Operation ............................................................................................................................................................... 15
8.1 Control elements................................................................................................................................... 15
8.2 Operation mode .................................................................................................................................... 15
8.2.1 Test operation for start-up..................................................................................................................... 15
8.2.2 Battery test............................................................................................................................................ 15
8.2.3 Group mode .......................................................................................................................................... 16
8.2.4 Single mode .......................................................................................................................................... 16
8.2.5 Programming ........................................................................................................................................ 16
8.3 Brightness-dependent switching ........................................................................................................... 16
8.4 Programming the device ....................................................................................................................... 17
8.4.1 Programming the device ....................................................................................................................... 17
8.4.2 Deleting programmed devices .............................................................................................................. 18
=== Ende der Liste für Te xtmarke TOC ===

Operating Instructions
Busch-Wächter®Safety
Operating Instructions | 1473-1-8136 — 3 —
Pos:6 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/S - T/Sicher heit @ 18\mod_1302612791790_15.d ocx @ 103357 @ 1 @ 1
1 Safety
Pos:7 /#Neustruktur#/Online-Dokumentation(+KNX)/Sicherheitshinweise und Hinweise(--> Füralle Dokumente<--)/Warnhinweise/Sicherheit - 230 V @ 18\mod_130260681675 0_15.docx @ 103308 @ @ 1
Warnin
g
Electric voltage!
Risk of death and fire due to electrical voltage of 230 V.
– Work on the 230V supply system may only be performed by authorised electricians!
– Disconnect the mains power supply prior to installation and/or disassembly!
Pos:8 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/A - F/Bestimmungsge mäßer Gebrauch @ 18\mod_1 302763321316_15.doc x@ 103483@ 1 @ 1
2 Intended use
Pos: 9 /#Neustruktur#/ Online-Dokumentati on (+KNX)/Besti mmungsgemäßer Gebrauch ( --> Für alle Dokumente <- -)/Busch-Dimmer/Besti mmungsgemäßer Gebrauc h @ 23\mod_13353504498 57_15.docx @ 208763 @ @ 1
The device is to be used exclusively with the components that are supplied and licensed as described in chapter
"Setup and function".
Pos: 10.1 /#Neustrukt ur#/Modul-Strukt ur/Online-Dokumen tation/Überschr iften (--> Für alle Dokument e <--)/1. Ebene/U - Z/Um welt @ 18\mod_1302614158 967_15.docx @ 103383 @ 1 @ 1
3 Environment
Pos:10.2 /#Neustruktur#/Online-Dokumentation(+KNX)/Sicherheitshinweiseund Hinweise(--> Für alleDokumente<--)/Hinweise/Hinweis- Umwelt - HinweisElek trogeräte @ 18\mod_130276 3973434_15.doc x@ 10350 0 @ @1
Consider the protection of the environment!
Used electric and electronic devices must not be disposed of with domestic waste.
– The device contains valuable raw materials which can be recycled. Therefore, dispose of the
device at the appropriate collecting depot.
Pos:10.3 /#Neustruktur#/Online-Dokumentation(+KNX)/Sicherheitshinweiseund Hinweise(--> Für alleDokumente<--)/Hinweise/Hinweis- Umwelt - EntsorgungEl ektrogeräte @ 20\mod_132 5760695972_15.doc x @ 136583 @ @1
All packaging materials and devices bear the markings and test seals for proper disposal. Always dispose of the
packaging material and electric devices and their components via the authorized collecting depots and disposal
companies.
The products meet the legal requirements, in particular the laws governing electronic and electrical devices and
the REACH ordinance.
(EU Directive 2002/96/EC WEEE and 2002/95/EC RoHS)
(EU REACH ordinance and law for the implementation of the ordinance (EC) No.1907/2006)
Pos:11 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ @ 1

Operating Instructions
Busch-Wächter®Setup and function
Operating Instructions | 1473-1-8136 — 4 —
Pos:12 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/A - F/Aufbau und Funk tion @ 11\mod_1279185435352_ 15.docx @ 83027 @ 111 @ 1
4 Setup and function
Pos: 13 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Aufbau un d Funktion/Waechter /Funktionen - 6747 220 WaveLI NE @ 28\mod_1347518563988 _15.docx @ 233247 @ 222222233 332233 @ 1
The Busch-Watchdog 220 WaveLINE is a versatile cableless movement detector with a 220° detection range and
is suitable for application on properties without a clear overview and for mounting to walls and ceilings.
The Busch-Watchdogs are passive infrared movement detectors which switch loads via the KNX bus when
sources of heat move within its detection range.
Busch Watchdog is not an intrusion or attack alarm.
Pos:14 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/2. Ebene/A - F/Funktions- und Au sstattungsmer kmale @ 23\mod_133655763 0140_15.docx @ 209136 @ 2222 22333332233 @ 1
4.1 Features of function and equipment
Pos: 15 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Aufbau un d Funktion/Waechter /Ausstattungsmerk male - 6747 220 WaveLINE @ 29\mod_1348 045004497_15.doc x@ 234 033 @ 122 @ 1
• Coverage of 16 m
• Radio transmission in the detection range
• Battery operation for line-independent installation
• Cableless retrofitting
• Detection and status indication
• Battery test
Pos:16 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 111 1 @ 1

Operating Instructions
Busch-Wächter®Setup and function
Operating Instructions | 1473-1-8136 — 5 —
Pos:17 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/2. Ebene/A - F/Erfassung sbereiche @ 19\mod_1320393 658466_15.doc x@ 10955 8 @ 2222221111 @ 1
4.2 Detection ranges
Pos:18 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/3. Ebene/U - Z/Übersic ht der Erfassungsbereic he @ 18\mod_1308563903037 _15.docx @ 106965 @ 333333212 3 @ 1
4.2.1 Overview of the detection ranges
Pos: 19 /#Neustruktur #/Online-Dokumen tation (+KNX)/Erf assungsbereiche/W aechter/Erfassungsber eiche - 6747 220 WaveLI NE @ 28\ mod_1347518519689_15. docx @ 233233 @ 1333222113333333 @ 1
4.2.2 Infrared range
Fig. 1: Infrared range
Detection range
• The detection range is 220° and the coverage is 16 m.
Ceiling mounting:
• The movement detector offers optimum surveillance if mounted to the ceiling at a maximum height of 2.5 m.
Pos:20 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/3. Ebene/A - F/Erfassung sbereiche Reduzier ung @ 29\mod_1347612043430 _15.docx @ 233618 @ 111111111 111213233223322 @ 1
4.2.3 Limitation of the detection range
Pos: 21 /DinA4 - Anleitung en Online/Inhalt/W aechter/Erfassungsb ereiche Einengung - 220° @28\mod_13 47374980807_15.doc x @ 232846 @ 21323222 @ 1
The horizontal detection range of the Busch-Watchdog is 220°. The detection range can be limited in case of
special local circumstances.
To do this, proceed as follows.
1. Cut the included adhesive film to the desired length.
2. Glue the section of covering foil from the front onto the area of the sensor of your Busch-Watchdog where the
detection is to be blocked out.
Note
For an illustration see chapter 7.1 on page 13.
Pos:22 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 122 2222 @ 1
max. 16 m
220°
2,5 m
16 m1 m

Operating Instructions
Busch-Wächter®Setup and function
Operating Instructions | 1473-1-8136 — 6 —
Pos:23 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/2. Ebene/P - R/Reichweit en der Funkübertragung @ 28\ mod_1347342242381_1 5.docx @ 232587 @ 22 @ 1
4.3 Radio transmission coverage
Pos: 24 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Montage/ Waechter/Reichwei ten der Funkübertragun g @ 28\mod_1347342169669 _15.docx @ 232573 @ 21 @ 1
Fig. 2: Radio transmission coverage
The values below are guideline values and may vary depending on local conditions:
Material / surface Guideline values
Direct (visual) connection Approx. 100%
Walls, ceilings and similar obstacles reduce the radio transmission coverage.
The following approximate values can be expected:
Material / surface Guideline values
Wood, plaster, uncoated glass 70 … 100 %
Bricks, chipboard 65 … 95 %
Reinforced concrete 10 … 90 %
Metal, aluminium lamination 0 … 10 %
Fire walls, lift wells, staircases and supply areas are considered as separating walls, just like the installation of
the receiver in metal housings.
The distance between the transmitter and the receiver and from other transmitters that also emit high-frequency
signals (e.g. computers, audio and video systems) should be 1.0 m minimum.
Pos:25 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 122 1 @ 1
max. 100 m
220 WaveLINE z. B. 6701

Operating Instructions
Busch-Wächter®Technical data
Operating Instructions | 1473-1-8136 — 7 —
Pos:26 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/S - T/Technisc he Daten @ 11\mod_1279185386 320_15.docx @ 83019 @ 3113333 3322233 @ 1
5 Technical data
Pos: 27 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Techni sche Daten/Waec hter/Technische Daten - 6747 @ 28\mod_1347265128303_15.doc x@ 232494 @ 332222323333 @ 1
Designation Value
Power supply IEC FR03 (L92 AAA 1.5 V) / IEC LR03 (AAA 1.5 V)
Horizontal detection 220°
Twilight sensor 0.5 … 300/∞lux
Maximum coverage (installed 2.5 m high) 16 m
Radio control range (free field) 100 m
Transmitter frequency 868.3 MHZ
Forced switch-off (min.) 180
Operating temperature -25 – 55°C
Protection type IP 55
Pos: 28 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Sic herheitshinweise und Hin weise (--> Füralle Dokumente<--)/Hinweise - Allgemein/Hinweis- Anschlussvon EVG's- Herstellerangaben @ 24\mod_1338458660462 _15.docx @ 214629 @ 121132323 3223222 @ 1
Information for the connection of ballasts
Please observe the following points regarding high inrush currents for ballasts:
- The ballast manufacturer’s specification determines the possible number of ballasts.
Pos:29 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 223 2222 @ 1

Operating Instructions
Busch-Wächter®Installation and electrical
connection
Operating Instructions | 1473-1-8136 — 8 —
Pos:30 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/M - O/Montage und e lektrischer Anschluss @ 23\ mod_1336477157864_15. docx @ 209033 @ 22222222222 2322222222232 @ 1
6 Installation and electrical connection
Pos: 31 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Sic herheitshinweise und Hin weise (--> Füralle Dokumente<--)/Warnhinweise/Sicherheit- Niederspannu ngs- und 230 V-Leitun gen @ 23\mod_133655886820 1_15.docx @ 209164 @ 11111111 1111 @ 1
Warnin
g
Electric voltage!
Risk of death due to electrical voltage of 230 V during short-circuit in the low-voltage line.
- Low-voltage and 230 V lines must not be installed together in a flush-mounted socket!
Pos: 32 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Sic herheitshinweise und Hin weise (--> Füralle Dokumente<--)/Warnhinweise/Sicherheit- Fachkenntnisse @ 23\mod_ 1336559183027_15. docx @ 209179 @ 222222222222222 22223222222 @ 1
6.1 Requirements for the electrician
Warnin
g
Electric voltage!
Install the device only if you have the necessary electrical engineering knowledge and experience.
• Incorrect installation endangers your life and that of the user of the electrical system.
• Incorrect installation can cause serious damage to property, e.g. due to fire.
The minimum necessary expert knowledge and requirements for the installation are as follows:
• Apply the "five safety rules" (DIN VDE 0105, EN 50110):
1. Disconnect from power;
2. Secure against being re-connected;
3. Ensure there is no voltage;
4. Connect to earth and short-circuit;
5. Cover or barricade adjacent live parts.
• Use suitable personal protective clothing.
• Use only suitable tools and measuring devices.
• Check the supply network type (TN system, IT system, TT system) to secure the following
power supply conditions (classic connection to ground, protective earthing, necessary
additional measures, etc.).
Pos:33 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 222 2222332232 @ 1

Operating Instructions
Busch-Wächter®Installation and electrical
connection
Operating Instructions | 1473-1-8136 — 9 —
Pos:34 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/2. Ebene/M - O/Montage @ 18\mod _1302615960458_15.doc x@ 103424@ 2222 2222222222223333333 33 @ 1
6.2 Mounting
Pos: 35 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Sic herheitshinweise und Hin weise (--> Füralle Dokumente<--)/Warnhinweise/Sicherheit- 230 V @ 18\ mod_1302606816750_15.d ocx@ 1033 08 @ 2222222222223322233 3333333 @ 1
Warnin
g
Electric voltage!
Risk of death and fire due to electrical voltage of 230 V.
– Work on the 230V supply system may only be performed by authorised electricians!
– Disconnect the mains power supply prior to installation and/or disassembly!
Pos: 36 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Montage/ Waechter/Montage - 6747 @ 28\mod_13472 65188412_15.doc x@ 232 508 @ 22222222222233333 223333 @ 1
Caution
Risk of damaging the device!
The lens of the device is sensitive and
can easily sustain damage.
- Do not press on the lens when
opening or closing the device.
6.2.1 Installation sites
Fig. 3: Installation sites
• Ceiling mounting in narrow rooms is not recommended.
• The mounting height of the device should be between 1.7 m and 2.5. m.
• The distance between light and movement detector should be at least 1.5 m.
• For optimum detection of persons the approach into the detection range should always be offset and never
frontal.
>1,7m

Operating Instructions
Busch-Wächter®Installation and electrical
connection
Operating Instructions | 1473-1-8136 — 10 —
6.2.2 Preparing the installation
To prepare the installation of the device, perform the following steps:
Fig. 4: Preparing the installation
No. Function
1 Locking screw
2 … 5 Clamps
1. Remove the locking screw (1) (if installed).
2. Press in clamps 2 - 5 on the sides of the housing with a suitable tool.
3. Carefully remove the front of the device.
Fig. 5: Opening the water drain
Depending on where the device is installed, the water drain may have to be opened.
• To do this, pierce the plastic membrane on the bottom of the device.
The installation is prepared.
1
23
4
5

Operating Instructions
Busch-Wächter®Installation and electrical
connection
Operating Instructions | 1473-1-8136 — 11 —
6.2.3 Mounting steps
1. Mount the device to the wall.
- Do not use countersunk head screws for mounting
to the wall.
- Use screws with a head diameter of 6.5 mm - 8.5
mm.
2. Open the battery compartment.
- Insert the enclosed type AAA batteries. Pay
particular attention to the battery poles.
Note
Do not use zinc-carbon batteries as replacement!
∅6,5 mm - 8,5 mm
∅3,5 mm - 3,9 mm

Operating Instructions
Busch-Wächter®Installation and electrical
connection
Operating Instructions | 1473-1-8136 — 12 —
3. Mount the upper part of the device.
- The bolting dimensions of the base may be
compatible with existing bores on older versions of
the Busch-Watchdog.
- Latch the upper part of the device onto the base.
4. To protect the device against unauthorized opening, the
enclosed screw can be used on the bottom of the
device.
- To protect the device against unauthorized opening,
screw the enclosed screw into the bottom of the
device.
Pos:37 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 222 22222 @ 1

Operating Instructions
Busch-Wächter®Commissioning
Operating Instructions | 1473-1-8136 — 13 —
Pos:38 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/G - L/Inbetri ebnahme @ 11\mod_12791854969 77_15.docx @ 83035 @ 3322212 21122 @ 1
7 Commissioning
Pos: 39 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Inbetri ebnahme/Waechter /Inbetriebnahme - 6747 @ 28\ mod_1347265305804_1 5.docx @ 232536 @ 222222222 222233332233 @ 1
7.1 Setting / limiting the coverage and the detection range
Caution
Risk of damaging the device!
The lens of the device is sensitive and
can easily sustain damage.
- Do not press on the lens when
setting the device.
Use the following steps to set the coverage and the detection range:
Fig. 6: Adjusting the lateral detection range
1. Adjust the lateral detection range by turning the head of the device.
Fig. 7: Adjusting the coverage
2. Adjust the coverage by lifting or lowering the head of the device.
– The minimum coverage is 6 m.
30°

Operating Instructions
Busch-Wächter®Commissioning
Operating Instructions | 1473-1-8136 — 14 —
Fig. 8: Adjusting the detection range by masking
3. The range can be specifically limited by gluing on the enclosed foil.
– Cut the enclosed foil to the size required.
The coverage and the detection range are set.
7.2 Activation test
The activation test can also be triggered via the service remote control (see separate operating manual).
Fig. 9: Activation test
To carry out the activation test, perform the following steps:
1. Set selector switch to T/S.
- The device is now in test mode for 10 minutes (daytime operation, switch-off delay 2 sec.). In addition,
each detection is indicated by the status LED flashing quickly.
- The device then switches back to the basic setting.
2. To carry out an additional activation test, set the selector switch back to position T or interrupt the
operating voltage supply for more than 15 seconds.
- The device is now in test mode for another 10 minutes. Test mode is exited automatically after 10 minutes
or by adjusting the brightness.
The activation test has been carried out.
Pos:40 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ 222 2222222222233332233 @ 1
TB
GS
ES
P

Operating Instructions
Busch-Wächter®Operation
Operating Instructions | 1473-1-8136 — 15 —
Pos:41 /#Neustruktur#/Online-Dokumentation(+KNX)/Überschriften(--> Für alleDokumente<--)/1. Ebene/A - F/Bedienung @ 11\ mod_1279185541649_15. docx @ 83043 @ 322222222223333 2233 @ 1
8 Operation
Pos: 42 /#Neustruktur #/Online-Dokumenta tion (+KNX)/Bedienu ng/Waechter/Bedi enung - 6747 @ 28\mod_13472651 03443_15.docx @ 232480 @ 2222 2222322233332233 @ 1
8.1 Control elements
Fig. 10: Control elements
No. Function
1 LED
- Flashes fast - detection in test mode
• Flashes 3 times - detection in standard and normal operation
2 Lens
3 Trim potentiometer for brightness value
4 Trim potentiometer for operating mode
5 Screw for dismantling safety
8.2 Operation mode
8.2.1 Test operation for start-up
Fig. 11: Test operation
After 10 minutes, the device automatically returns to the basic setting ("GS" operating mode). Set the desired
operating mode “GS” or “ES”.
After activating the mains supply voltage the device remains in test mode for 10 minutes (see
chapter "Activation test").
8.2.2 Battery test
Fig. 12: Battery test
If the battery voltage is sufficient, the LED (pos. 1) lights up for approx. 10 seconds. If the LED flashes, the
voltage is too low. Please replace the batteries! After 30 seconds, the device automatically returns to the basic
setting. Set the desired operating mode “GS” or “ES”.
11
2
3
4
5
TB
GS
ES
P
TB
GS
ES
P

Operating Instructions
Busch-Wächter®Operation
Operating Instructions | 1473-1-8136 — 16 —
8.2.3 Group mode
Fig. 13: Group mode
If persons move in the detection area, switching signals will be transmitted. The brightness limit value can freely
selected. The switch-off delay has to be set via the actuator (receiver).
In this operating mode, several watchdogs and actuators can communicate with each other.
8.2.4 Single mode
Fig. 14: Single mode
If persons move in the detection area, switching signals will be transmitted. The brightness limit value can freely
selected. The switch-off delay is fixed to 3 minutes. The switch-off delay of the receiver, e.g. 6701, must be set to
a value > 3 minutes.
In this operating mode, only one watchdog can send signals to a specific actuator.
8.2.5 Programming
Fig. 15: Programming
Note
The individual programming steps are contained in chapter 8.4 "Programming devices" on page 17.
8.3 Brightness-dependent switching
Icon Function
Switching during all brightness levels
Switching during advancing twilight
Switching during darkness
TB
GS
ES
P
TB
GS
ES
P
TB
GS
ES
P

Operating Instructions
Busch-Wächter®Operation
Operating Instructions | 1473-1-8136 — 17 —
8.4 Programming the device
8.4.1 Programming the device
For programming, perform the following steps:
Fig. 16: Selector switch of the receiver
1. Set the selector switch of receiver 6701 on "P", LED flashes green.
Fig. 17: Programming button
2. Press the programming button on receiver 6701 (2), the LED (1) lights permanently green.
Fig. 18: Set the selector switch on “P”.
3. Set the selector switch of the Busch-Watchdog on "P", the status LED lights up for approx. 10 seconds (with a
slight delay).
4. The devices are being programmed to each other.
5. After successful programming, the LED starts to flash green again. If programming is not successful (the LED
continues to light up), reset the selector switch on the Busch-Watchdog to “P” and repeat the procedure.
6. Set the operating mode of receiver 6701 on "R" or "S" or program additional Watchdogs.
7. Select the operating mode of the Busch-Watchdog on “ES” or “GS”.
P
R
S
EA
E
1+2
TB
GS
ES
P

Operating Instructions
Busch-Wächter®Operation
Operating Instructions | 1473-1-8136 — 18 —
8.4.2 Deleting programmed devices
Tor delete all programming take the following steps:
Fig. 19: Selector switch of the receiver
1. Set the selector switch of receiver 6701 on "E", LED flashes red.
Fig. 20: Programming button
2. Press the programming button on receiver 6701 (2), the LED (1) lights permanently red.
Fig. 21: Set the selector switch on “P”.
3. Set the selector switch of the Busch-Watchdog on "P", the status LED lights up for approx. 10 seconds (with a
slight delay).
4. The link will be deleted.
5. After a successful deleting process, the LED starts to flash red again. If the deleting procedure is not
successful (the LED continues to light up), reset the selector switch on the Busch-Watchdog to “E”again and
repeat the procedure.
6. Set the operating mode of receiver 6701 on "R" or "S" or program additional Watchdogs.
7. Select the operating mode of the Busch-Watchdog on “ES” or “GS”.
Pos:43 /#Neustruktur#/Online-Dokumentation(+KNX)/Steuermodule- Online-Dokumentation(--> Für alleDokumente<--)/++++++++++++Seitenumbruch + +++++++++++ @ 9\mod_12688 98668093_0.doc x@ 52149 @ @ 1
P
R
S
EA
E
1+2
TB
GS
ES
P

Operating Instructions
Busch-Wächter®Operation
Operating Instructions | 1473-1-8136 — 19 —
=== Ende der Liste für TextmarkeConten t ===

Operating Instructions
Busch-Wächter®
1473-1-8136 | Rev. 01 | 11.2012
Pos:45 /#Neustruktur#/Online-Dokumentation(+KNX)/Rückseiten(--> Für alleDokumente<--)/Rückseite- Busch-Jaeger - Allgemein @ 28\mod_1347009 779995_15.doc x@ 23228 2@ @ 1
A
member of the ABB Group
Busch-Jaeger Elektro GmbH
PO box
58505 Lüdenscheid
Freisenbergstraße 2
58513 Lüdenscheid
Germany
www.BUSCH-JAEGER.com
[email protected]om
Central sales service:
Phone: [phone]
Fax: [phone]
Notice
We reserve the right to at all times make
technical changes as well as changes to the
contents of this document without prior notice.
The detailed specifications agreed to at the time
of ordering apply to all orders. ABB accepts no
responsibility for possible errors or
incompleteness in this document.
We reserve all rights to this document and the
topics and illustrations contained therein. The
document and its contents, or extracts thereof,
must not be reproduced, transmitted or reused by
third parties without prior written consent by ABB.
Copyright© 2012 Busch-Jaeger Elektro GmbH
A
ll rights reserved
=== Ende der Liste für TextmarkeBackc over ===