ABH 6830 Series User manual

c 2014 ABH Mfg., Inc.
printed in USA
R
Owww.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
6830 REVERSE EXIT ONLY-1-03.DWG
6830 REVERSE
EXIT ONLY
REVISED 09-16-14
PHILLIPS PAN HD. M.S.
NOTE: REVERSE INSTALLATION INSTRUCTIONS #4 & # 3 THEN CONTINUE
WITH INSTRUCTIONS 1, 2 & 3 BELOW.
REMOVE THE (2) 10-32 SHOULDER BOLTS WITH SPRINGS THAT SECURE
THE CAM HOLDER ASSEMBLY, NOTE THE DIRECTION OF THE LOCATING
PIN BEFORE STARTING.
ROTATE THE CAM HOLDER ASSEMBLY 180°.
REINSTALL THE (2) 10-32 SHOULDER BOLTS WITH SPRINGS.
PUSH/PULL LATCHES ARE ASSEMBLED FOR RIGHT HAND AND LEFT HAND DOORS. BE SURE CORRECT SIDE
MATCHES DOOR APPLICATION.
PLACE LATCH BOLT UNIT IN DOOR MAKING SURE BOLT BEVEL FACES DIRECTION OF DOOR CLOSING.
ATTACH FRONT WITH TWO (2) #8 OR 8-32 SCREWS DEPENDING ON DOOR.
POSITION LEVER ASSEMBLY SO THAT LOCATING PIN AND CAM ARM ENTER INTO CORRESPONDING HOLES IN
LATCH BOLT UNIT. ATTACH LEVER ASSEMBLY BY THRU BOLTING ONTO EXIT ONLY PLATE WITH FOUR (4)
#10-32 X 1-1/2" PHILLIPS PAN HD. M.S. FOR PURPOSE OF ALIGNMENT DO NOT TIGHTEN SCREWS UNTIL ALL
FOUR (4) SCREWS HAVE BEEN STARTED.
APPLY COVERS AND FASTEN WITH (2) 8-32 X 3/8" FLAT HD. M.S. FOR EACH COVER.
INSERT DUST BOX IN FRAME MORTISE AND ATTACH STRIKE WITH TWO (2) #8 OR 8-32 SCREWS.
3.
2.
TO CHANGE DIRECTION OF PUSH OR PULL HANDLE
INSTALLATION INSTRUCTIONS
1.
5.
4.
2.
3.
1.
6830 SERIES REVERSE EXIT ONLY
(4) 10-32 X 1-1/2"
(2) #8 OR 8-32 SCREWS
PHILLIPS FLAT HD. M.S.
BEVEL FACES THE
DIRECTION OF DOOR
MAKE CERTAIN BOLT
CLOSING
(2) 8-32 X 3/8"
DOOR PREPARATION
TYPICAL FINISHED
COVER
PULL SIDE OR PUSH SIDE ASSEMBLY
LOCATING PIN GUIDE
LATCH BOLT UNIT
EXIT ONLY PLATE
LISTED
L
U
PATENT PENDING
LOCATING PIN
CAM HOLDER
10-32 SHOULDER BOLTS
WITH SPRINGS
PULL SIDE SHOWN
FOR EXAMPLE

c 2014 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R
PULL SIDE
THICKNESS
#12-24
BACKSET
"T" STRIKE & DUST BOX
ASA STRIKE & DUST BOX
3. Mortise to required strike and box depth
2. Center strike and mark screw positions
1. Mark centerline of latch bolt on frame
FRAME PREP
3. Verify backset (2-3/4", 3-3/4", 5"or 7"). Tape template to door.
2. Locate horizontal centerline on door
1. Install door
DOOR PREP
LATCH
1-1/4
1-1/4 (2) TAP
1-1/23-3/8
4-7/8
4-1/8
3/32
3/8
1/4
1/4
3/8
5/64
1-5/16
1-1/8
9/16
2-3/4
2-1/8
OF
L
C
(OR SILENCER)
EDGE OF STOP
1/2 DOOR
VERIFY
TEMPLATE
(4) 3/8" DIA THRU
2-1/8" D. DR. THRU
FOR BACKSET
SEE TEMPLATE
C
L
C
L
(2) #8 F.H.W.S. OR 8-32 F.H.M.S.
DRILL 1-1/8" D. TO INTERSECT 2-1/8" D HOLE
OF DOOR
L
C
2-1/4
1-1/8
1-5/8
13/16
5/32
9/16
1-1/8
6830 REVERSE EXIT ONLY-2-03.DWG
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
4. All dimensions in inches.
"D" STRIKE
1/32
15/16
4-3/4
1-5/32
4-1/8
3-1/4 3-3/16
1"
1/16
3/8
3/16
1-11/16
1/2
21/32
PREP FOR #8 SCREW
1-3/16
2-1/4
1-11/16
1
1
1-11/16
1/2
21/32
601LB STRIKE
1-3/16
3/16
1/16
3/8
9/64
2-1/4
1-11/16
1/32
9/16
1-3/16
1-5/32
61/64
2-1/8
2-11/16
1-1/4
PREP FOR #8 SCREW
PREP FOR #8 SCREW
LATCH/HANDLE ASSEMBLY
1. Install latch bolt.
Radius portion of latch bolt must
face push side of door.
2. Install push or pull side handle assembly with latch
shaft thru latch bolt assembly.
3. Mount Exit only plate and install using
(4) 10-32 screws with (4) 10-32 sex bolts.
4. Mount Cover.
6830 REVERSE
EXIT ONLY
REVISED 09-16-14
BORE
5-3/8"
4-3/8"
6-5/8"
8-5/8"7"
5"
2-3/4"
3-3/4"
BACK SET DEPTH
OF
WOOD DOOR