ABH LR6600 PS User manual

2
4
5
ISSUED 06-23-20
PATENT PENDING
PAGE 1 OF 3
INSTALLATION INSTRUCTIONS:
1. Install mortise lock body (item 1) using (2) 12-24 combo screws (item 9). Mount mortise lock face plate (item 8) using
(2) 8-32 FHMS (item 10).
2. Determine if handle & base assembly (item 4) is to be mounted vertical or horizontal. Place handle assembly on
appropriate side of door and rotate cam as per detail "A", shown above. In detail "B", insert (2) 10-32 sex bolt (item 11)
that match the holes on the door face through the handle & base assembly (item 4) and mortise lock body (item 1) into
the exit only plate and attach with (2) 10-32 screw (item 7).
3. Test lock for proper operation. If latch bolt does not extend or retract freely because of any type of binding, loosen
mounting screws to adjust alignment of trim handle & base assembly (item 4) and re-tighten screws one at a time while
checking latch bolt movement.
4. To prevent the handle & base assembly (item 4) from possible twisting, which in turn can cause binding, determine
which staking screw hole will be used. (the staking screw installs on the staking screw hole location opposite the
direction the handle is mounted). Install (1) #12 PHSMS staking screw (item 6).
5. Place cover (item 2) over handle and fasten each side with (2) 8-32 oval head screws (item 5).
DETAIL "A"
NOTE:
BEFORE MOUNTING BASE ASSEMBLY,
CAM MUST BE ROTATED AS PER
DRAWING SHOWN IN DETAIL "A".
(MUST POINT
HANDLE
HORIZONTAL
DOWN
HANDLE
UP
HANDLE
** HINGE SIDE)
**
1
STAKING
SCREW HOLE
6
LR6600 - EXIT ONLY OPTION
INSTALLATION FOR MORTISE LOCK TRIM
"PS" OPTION - LR6600 TRIM ON PUSH SIDE & EXIT ONLY PLATE ON PULL SIDE
"PL" OPTION - LR6600 TRIM ON PULL SIDE & EXIT ONLY PLATE ON PUSH SIDE
LR6600 - EXIT ONLY
"PS" or "PL" OPTION
LR6600 - EXIT ONLY PS OR PL OPTION-1-02.DWG
BASE ASSEMBLY
6-32 X 3/8" SHCS
7 (10-32 X 1/2" FHMS)
HANDLE ASSEMBLY
DETAIL "B"
3
5
6-32 X 3/8" SHCS
STOP PIN
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN OR HORIZONTALLY.
2. USE ABH MORTISE LOCK DOOR PREP TEMPLATE.
3. MORTISE LOCK CYLINDER NOT PROVIDED.
10
9
9
8
PARTS LIST
DESCRIPTIONQTY
ITEM
1MORTISE LOCK BODY 1
2 COVER1
3 1
4 1
58-32 X 3/8" OVAL HEAD MS 2
61
EXIT ONLY PLATE ASSEMBLY
#12 X 1/2" PHSMS STAKING SCREW
HANDLE & BASE ASSEMBLY
7 10-32 X 1/2" FHMS
2
8
9
10
1
2
2
FACE-PLATE, MORTISE LOCK
12-24 X 3/4" FH COMBO SCREW
8-32 X 1/4" FHMS
(SEE DETAIL "B"
FOR EXPLODED
VIEW)
11 210-32 X 1-1/2" SEX BOLT
11
c 2020 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)

Lockset function
Caution: Not all holes shown above need
to be drilled. Use the diagram AND the
chart to determine the holes that you need
to drill for your trim and function
combination.
LR6610
Cylinder
1-1/4" dia. 5/8" dia.
Turn knob
1-1/8" dia.
Trim
1/2" dia.(2)
Thru-bolt Emergency Key
1 2 4 5 1 2 4 5
Cylinder Trim
1-1/8" dia.
Thru-bolt
1/2" dia.(2)
Outside holes
Inside holes
LR6638
LR6632
ADA recommends mounting centerline of lock 44" from top of finished floor.
LR6641
Determine trim holes based on trim type.
*
6
(2)
Trim turn knob
*
6
(2)
Trim turn knob
1-1/4" dia. 1/2" dia.
-OR- Check local ordinance for proper height.
LR6652
(Passage/Closet Latchset)
(Privacy)
LR6637 (Store Door Lock)
(Entry/Restroom Lock)
(Asylum Lock)
LR6645 (Hotel/Motel Lock)
(Office Lock)
LR6653 (Entry/Office Lock)
(Classroom Lock)
(Dormitory Lock)
(Storeroom/Exit Lock)
(Dormitory/Bedroom Lock)
LR6656
LR6657
LR6658
LR6654
1
5
5
4
1-1/4 dia.
1/2 dia.
1-1/8 dia.
1/2 dia.
SEE CHART 2
6
*
LR6600 EXIT ONLY - PS OR PL OPTION
HOLE PATTERN CHART
REVISED 07-25-16
*
PAGE 2 OF 3
LR6600 - EXIT ONLY
"PS" or "PL" OPTION
LR6600-EXIT ONLY PS OR PL OPTION-2-02.DWG
c 2020 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)

Lock case holes:
1 Cylinder hole-1-1/4" dia.
2 Turn knob-5/8" dia. / Emergency key-1/2" dia.
4 Trim hole-1-1/8" dia.
5 Thru-bolt holes- (two required) 1/2" dia.
Notes:
1. Before drilling check the hole pattern chart.
2. The maximum door-to-frame gap is 3/16".
3. Allow 3/64" clearance for the strike box thickness.
4. For metal door, lock case support is required from
the door manufacturer.
5. Tap for a #12-24 machine screw or drill for a #12
wood screw (a combination screw is supplied).
LR6600 EXIT ONLY - PS OR PL OPTION
DOOR & FRAME PREP
REVISED 07-25-16
PAGE 3 OF 3
LR6600 - EXIT ONLY
"PS" or "PL" OPTION
LR6600-EXIT ONLY PS OR PL OPTION-3-02.DWG
of lock 44" from top of finished floor.
ADA recommends mounting centerline
FINISHED FLOOR
5
3
4
CENTERLINE
OF LEVER
CENTERLINE
OF LOCK
TOP VIEW
SHOWN WITH DEAD BOLT
FRONT VIEW
SHOWN WITH OUT
DEAD BOLT
FRONT VIEW
SHOWN WITH
DEAD BOLT
ASA STRIKE
STRIKE BOX
SIDE VIEW
SHOWN WITH DEAD BOLT
5
2
227
64
TAP FOR #12-24
MACHINE SCREW
OR #12 WOOD
SCREW (2 PLACES)
1
57
8
35
8
13
16
ADJUSTABLE BETWEEN
86.5° AND 93.5°
1
8
41
4
1
23
4 BACKSET
1
17
8
CLEARANCE FOR
SCREWS-1/16"
7
32 DEEP
111
16
45°
11
2
7
32
11
4
8
71
4
4
11
16
3
8
33
8
CENTERLINE
OF STRIKE
41
8
37
16
(STRIKE
BOX)
47
8
11
4
3
64
17
32
31
32
11
32
19
32
13
16
19
32
13
16
-OR-
Check local ordinance for proper height.
5
64
c 2020 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)