AbodeFit WalkSlim 920 User manual

WalkSlim 920
TREADMILL • USER MANUAL

Congratulations on your purchase of the AbodeFit Health™
WalkSlim 920.
Please read the user manual carefully before using,
pay special attention to the safety precautions and keep
for future reference.
WARNING
Keep young children away from this treadmill at all times.
Contact with the moving surface may result in severe friction burns.
Please contact AbodeFit Health’s warranty provider,
Vitality 4 Life, (details on back page) if any malfunction
occurs and a qualified technician will assist you.
Unauthorised dismantling of the treadmill will void
warranty.
Stop using the treadmill immediately if:
• Water comes into contact with the treadmill or
the controller
• Any foreign bodies have been lodged inside the
treadmill
• Power failure
• Thunder / lightning weather
• If you feel unwell
• If the power cord has any damage

Safety Precautions 4
Parts and Features 6
Operating Instructions 7
Using your Walkslim 920 9
Warm Up Exercises 10
Maintenance 12
Troubleshooting 14
Warranty 17
EN
3

EN
4
Safety Precautions
• The WalkSlim 920 is only suitable for adults over the age of 18. It is not a toy and
should not be used by children.
• The WalkSlim 920 is for personal use only and is unsuitable for professional training,
testing or medical purposes.
• The WalkSlim 920 is designed for indoor use only. Do not use in areas of strong light
or heat (including direct exposure to the sun), when temperatures exceed 40°C or
near water
• Do not use the WalkSlim 920 in humid or dusty environments to avoid any risk of
electric shock.
• To avoid any injury, warm up exercises are advised prior to using the treadmill. It
is not recommended to use your WalkSlim 920 for walking or running within 40
minutes of eating.
• Only use if you are in good health. If you feel uncomfortable (dizzy, headache or have
physical problems such as ligament injuries or joint replacements) stop using the
treadmill immediately and seek professional advice.
• The WalkSlim 920 is not suitable for use by individuals with reduced physical,
sensory or mental capabilities unless professional guidance has been given.
• Always wear appropriate footwear when using the treadmill, avoid exercising
barefoot or wearing any loose jewellery or clothing with belts or strings.
• Do not insert hands or feet or any body parts into the treadmill or in areas between
the tread belt and footrails.
• Stop for 30 minutes after each one hour running or walking session to avoid any
damage to the motor as a result of overheating.
• Ensure the WalkSlim 920 is on a flat and dry surface before use and there are no
sharp items close by.
• The WalkSlim 920 is not suitable for using on every carpet type, therefore if you
intend to use the treadmill on any carpeted areas, it is strongly advised that a hard-
mat type material is placed beneath the treadmill.
• Only connect the WalkSlim 920 to a power outlet that is the correct size for the
power plug and do not use if the power plug is damaged.
• Do not use force to disassemble any parts or attempt to turn off the power while
in use.
• Do not insert foreign objects into any of the parts or use unauthorised parts.

EN
5
• Do not apply pressure or stand on the touch screen.
• Do not exceed the treadmill’s maximum weight capacity of 110kgs, the treadmill is
only suitable for individual use.
• Keep a distance of 1 metre between the treadmill and the rear space and on
both sides.
• Unplug the WalkSlim 920 when it is not likely to be used for long periods of time.
• Do not let cord contact any other parts such as tread belt.
• Make sure the cord is undamaged and located where it cannot be damaged.
• Please turn off and dry any spilt liquid before cleaning the treadmill
• Do not fold the soft close frame down while the power is on. Switch the power off
to allow the tread belt to come to a complete stop before folding. A folded treadmill
should not be operated.
• Unplug the power cord when the treadmill is not in use.
BEFORE USING THE WALKSLIM 920
• Wait an appropriate time after eating
• Ensure children and pets are kept away from the treadmill
• Make sure no fingers or foreign bodies are near the gap between the cover and the
base of the treadmill whilst in operation
• Always supervise young and elderly people whilst on the treadmill
• Only one person may be on the tread belt at a time
CONSULT YOUR DOCTOR PRIOR TO USE IF ANY OF THE FOLLOWING APPLIES:
• you are undergoing medical treatment or have any medical concerns
• you are pregnant
• you have heart disease
• you have osteoporosis
• you have a pacemaker or other medical electronic instrument implanted
• you have artificial limb/s

EN
6
Parts and Features
Touch Screen
2. Introduction of display screen
02 Structure and Function Diagram
05 06
Time
HIIT
Program
Walking
Program
Distance
Fat Burning
Program
Speed
Automatic
Speeds
Bluetooth
Status
Indicator
Function Dial
Press to Start/
Stop/Pause
Turn to Adjust Speed
Calories
Foldable Hydraulic Handles
Footrail
Tread Belt
Silicone Lubricating Oil
& Allen Key
Phone Holder
Safety Key
Insert
Handle
Release
Button
Touch Screen

EN
7
Operating Instructions
STARTING YOUR WALKSLIM 920
• First find the right spot for your WalkSlim 920 , ensuring you choose a location that is
flat and open, free of sharp objects, with a sufficient 1 metre clear space around the
treadmill.
• Remove the WalkSlim 920 from its packaging and place face down on the floor, clear
of sharp objects or anything likely to scratch its surface.
• Before you use the WalkSlim 920 the tread belt must be lubricated with the oil
provided.
HOW TO LUBRICATE THE TREAD BELT
• Lubricating your WalkSlim 920 treadmill is essential before starting to use it for the
first time along with during normal use.
• During normal use, friction marks may appear between the tread belt surface and
the treadmill base. To avoid unnecessary friction and to maximize the life of your
treadmill, it is recommended to lubricate the tread belt surface with lubricant after
every 10-15 times or according to the following schedule:
• Lightweight users (less than 3 hours/week) - Lubricate once every 3 months
• Moderate users (3-6 hours/week) - Lubricate once every 2 months
• Heavyweight users (more than 7 hours/week) - once every month
• Do not lubricate too much
Power Switch
Power Socket
Wheels

EN
8
The following is a step-by-step guide
1. Make sure the treadmill is unplugged and place it on an even,
non-slippery surface.
2. Lift the tread belt surface up starting from the upper corner.
3. Apply the lubricant by squeezing droplets on the underside
of the tread belt surface, ensuring the lubricant is applied at
least 10-15cm towards the middle of the tread belt.
• Remember proper lubrication is an important factor in
maintaining the treadmill. To check if you need to add
lubricant, make sure the treadmill is turned off at the power
outlet. Run your hand under the tread belt from the top to the
bottom. If your hand is slightly damp with silicone oil there is
no need to lubricate. If your hand is completely dry, it is time
to add lubricant.
STARTING THE WALKSLIM 920 USING THE ON-BOARD PROGRAMS
1. Place the Walkslim 920 on a level surface and lift the frame up from the side of the
treadmill.
2. Rotate the handles in the direction of the arrows while holding the Handle Release
button which is located below the handles. Check if the handles are locked.
3. Connect the power plus and turn the power switch on.
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD

EN
9
4. Before starting your training, insert the Safety Key into the Safety Key Insert and clip
the other end to your clothing.
5. Press the Function Dial and the Walkslim 920 will start slowly at the minimum speed
of 0.8km/hour.
6. Select your preferred on-board program or speed by pressing either the HIIT,
Fat Burning, Walking Program buttons or the Automatic 3Km/hr, 6Km/Hr or
9Km/Hr Speed Selection buttons.
HIIT is a High Intensity Interval Training Program designed to efficiently improve
your athletic ability and may help you burn more calories in a shorter amount of
time.
Fat Burning is a Medium Intensity Program that targets fat burning
Walking is a Low Intensity Program for those who have no running experience or
would like a less vigorous workout.
HOW TO SPEED UP
Rotate the Function Dial to increase the speed by 0.1km/hour per each mark.
HOW TO PAUSE
Press the Function Dial during operation to Pause.
HOW TO STOP
In an emergency, hold the handles tightly with both hands and step off the tread belt
onto the side platforms. Activate the Emergency Stop machanism by pulling out the
Safety Key from the insert. This will safely disconnect the treadmill and the motor will
immediately stop running. The Treadmill will only start up again if the Safety Key is
inserted back in.
1. Description of the mode button 2. Description of the HIIT mode 5. Description of Mode Selection
04 Learn to Use the Treadmill
09 10
HIIT is a high-intensity interval training mode that
can effectively improve the athletic ability.
HIIT mode
Fat burning mode
Walking mode
3. Description of Fat burning mode 4. Description of the walking mode
Walking mode, is a low-intensity exercise mode
suitable for users who have no running experience
and have used the treadmill for the first time.
Fat burning mode, is a medium-intensity exercise
mode that can effectively burn off calories.
After power-on, press the center function key to start working out directly. Then the machine starts slowly to the minimum
start-up speed (0.8km/h). At this time, enter the corresponding motion mode by selecting the icon. After pressing the speed
shortcut key, adjust the speed of this movement by rotating the center function key(the speed changes 0.1km/h each mark),
and then press the center function key again to enter the pause state. By the speed shortcut key,you can define the speed value
via APP and send to the treadmill.
1. Description of the mode button 2. Description of the HIIT mode 5. Description of Mode Selection
04 Learn to Use the Treadmill
09 10
HIIT is a high-intensity interval training mode that
can effectively improve the athletic ability.
HIIT mode
Fat burning mode
Walking mode
3. Description of Fat burning mode 4. Description of the walking mode
Walking mode, is a low-intensity exercise mode
suitable for users who have no running experience
and have used the treadmill for the first time.
Fat burning mode, is a medium-intensity exercise
mode that can effectively burn off calories.
After power-on, press the center function key to start working out directly. Then the machine starts slowly to the minimum
start-up speed (0.8km/h). At this time, enter the corresponding motion mode by selecting the icon. After pressing the speed
shortcut key, adjust the speed of this movement by rotating the center function key(the speed changes 0.1km/h each mark),
and then press the center function key again to enter the pause state. By the speed shortcut key,you can define the speed value
via APP and send to the treadmill.
1. Description of the mode button 2. Description of the HIIT mode 5. Description of Mode Selection
04 Learn to Use the Treadmill
09 10
HIIT is a high-intensity interval training mode that
can effectively improve the athletic ability.
HIIT mode
Fat burning mode
Walking mode
3. Description of Fat burning mode 4. Description of the walking mode
Walking mode, is a low-intensity exercise mode
suitable for users who have no running experience
and have used the treadmill for the first time.
Fat burning mode, is a medium-intensity exercise
mode that can effectively burn off calories.
After power-on, press the center function key to start working out directly. Then the machine starts slowly to the minimum
start-up speed (0.8km/h). At this time, enter the corresponding motion mode by selecting the icon. After pressing the speed
shortcut key, adjust the speed of this movement by rotating the center function key(the speed changes 0.1km/h each mark),
and then press the center function key again to enter the pause state. By the speed shortcut key,you can define the speed value
via APP and send to the treadmill.
TIP
Uncontrolled use of the treadmill can be avoided by removing the Safety Key and storing it in a secure place.
Please carefully consider your physical conditions when starting to use this product for training, and keep training properly and
regularly to ensure that you have enough physical strength to exercise. Inappropriate or excessive training will not benefit your
health.
03 Guidance for initial Operation
07 08
5. Connect the power supply
and turn on the switch.
8. Start to use the treadmill.
Noisy level is 65dB(A).
The treadmill has an emergency stop mechanism for your safety. Before starting
your training, attach the safety key to your clothing. If the treadmill was switched
off due to the safety key being pulled out, insert it again. The continuous belt
does not start up again automatically.
Uncontrolled use of the treadmill by a third party can be avoided by taking the
safety key off and storing it in a secure place.
In an emergency, hold the handrails tightly with both hands and step off of the
belt onto the side surfaces of the side platforms. Activate the emergency stop
mechanism (safety disconnect).
4. Check if the handrail is locked.3. Rotate the handrail in the direction of arrows while
holding the lockup button below the handrail.
7. Open APP homepage, add the
device by "+" in the upper right
corner of the page, and complete
the phone binding according to the
prompt.
6. Search "KS RECORD" App from
Apple Store or Android Google
Play and complete installation.
1. Remove the machine from the package, and
place the machine on a level surface.
2. Lift the column of the machine
from the side of the machine.
KS RECORD

EN
10
Warm-Up Exercises
It is recommended to warm up for 5 to 10 minutes before exercise to prevent sports
injuries. Refer to the following stretching exercises and repeat after your treadmill
exercise program.
1. Stretch down: Keep knees slightly flexed and your body slowly bent forward, relax
your back and shoulders, touch your toes with your hands as much as possible, and
keep for 10~15 seconds, then relax. Repeat 3 times.
2. Foot tendon stretch: Sit on a clean seat cushion, straighten one leg and keep the
other leg inward to fit the inner side of the straight leg. Try to touch your toes with
your hands for 10 to 15 seconds, then relax. Repeat 3 times for each leg.
3. Stretch the calves and Achilles tendon: Stand close to a wall with your hands on
it, with one foot behind, keep the back leg upright and heels touching the ground,
incline to the wall and keep for 10 to 15 seconds, then relax. Repeat 3 times for each
leg.
4. Stretch the quadriceps: Balance yourself with the left hand holding a wall or a desk,
then extend your right hand backwards, grab your right heel and slowly pull it to your
buttocks until you feel the muscles on the front of the thighs in tension, keep for 10 to
15 seconds, then relax. Repeat 3 times for each leg.
5. Stretch the sartorius muscle (muscle inside the thigh): Keep the soles opposite and
sit with the knees outwards. Grasp your feet with your hands and pull in the direction
of your groin, keep for 10 to 15 seconds, then relax. Repeat 3 times.

EN
11
Storing the WalkSlim 920
• The maximum ground clearance is 32cm so you can store the treadmill in places that
are suitable for its size (L142 x W83 x H31cm)
• Do not store the treadmill edge-on
• If you prefer to store it upright, the WalkSlim 920 comes with a base which holds up
to 110kg.
06 Safety Instructions
13 14
Keep the space between the
treadmill and two sides above
500 mm.
Please use it carefully for elders
and pregnant women.
Do not place it uneven ground.
Do not step on the treadmill
motor cover.
Please ensure the surrounding
environment secure when storing
and place the machine in a stable
position.
Please use the treadmill
correctly.
Pets are strictly prohibited.
Do not store the treadmill
edge-on.
Keep the distance of 2000 mm ×
1000 mm between the treadmill
and the rear space.
Please wear sports shoes. Do clip the safety lock clip to the
clothes when using.
(Pull off the safety lock to
immediately stop the motor
running if there is an unexpected
situation.)
Unplug the power cord when the
treadmill is not in use.
Please ensure the machine
is stable when storing.
06 Safety Instructions
13 14
Keep the space between the
treadmill and two sides above
500 mm.
Please use it carefully for elders
and pregnant women.
Do not place it uneven ground.
Do not step on the treadmill
motor cover.
Please ensure the surrounding
environment secure when storing
and place the machine in a stable
position.
Please use the treadmill
correctly.
Pets are strictly prohibited.
Do not store the treadmill
edge-on.
Keep the distance of 2000 mm ×
1000 mm between the treadmill
and the rear space.
Please wear sports shoes. Do clip the safety lock clip to the
clothes when using.
(Pull off the safety lock to
immediately stop the motor
running if there is an unexpected
situation.)
Unplug the power cord when the
treadmill is not in use.
Do not store treadmill
upright on its side.
1. Clean the treadmill • Shut down and disconnect the power from the treadmill.
• Wipe off the dust and smudges from the main frame and the motor over with a 100%
cotton rag dipped with a little of mild detergent. Do not spray the cleaner directly onto
the running belt or use the acid and corrosive cleaners while cleaning the surface of the
running belt. Do not wipe under the running belt. It is normal that there may be dust and
smudges on the rear ground after the product is used for a period of time. Please
remove the dust and smudges.
• Running belt inclined left: Turn the left adjustment screw 1/4 circle clockwise.
• Running belt inclined right: Turn the right adjustment screw 1/4 circle clockwise.
• Slip running belt: Turn the left and right adjustment screws clockwise at the same time a
half circle to run the running belt for a period of time (1~2 minutes) to observe the
centering situation. If necessary, please adjust it again.
• Shut down and pull out the power cord of the treadmill.
• Lift the edge of the running belt and apply silicone oil to the inner surface . Power on the
treadmill again to run the running belt at 4km/h for 10-20 seconds
• 5-10 ml of silicone oil is needed for one time of lubrication. If the lubrication is applied
too much, the belt will slip and affect normal use.
• Add the silicone oil every 3 months.
06 Safety Instructions 07 Maintenance and Servicing
15 16
Do Not Step to Prevent Being
Involved.
Keep the horizontal sight to void
visual dizziness.
Do Not Step to Prevent Being
Involved.
For Single-user only.
Warning, to allow the running
surface to come to a complete stop
before folding. Do not fold with
power on. A folded treadmill should
not be operated.
2. Slip running belt and correction
3. Lubricate the running belt
Horizontal sight
Do not walk sideways.
Allow treadmill to come
to a complete stop. Turn
power off and remove
power
cord before folding
treadmill for storage.

EN
12
Maintenance
Daily Maintenance
• Regular comprehensive cleaning will extend the life of your WalkSlim 920
• Always turn the power off at the power outlet and make sure there is no moisture
before daily cleaning and maintenance.
• Clean dust out regularly and ensure the exposed parts of the tread belt are clean.
• Wear clean sports shoes to avoid any dust or impurities getting into the tread belt
and board.
• Use a damp cloth with soap or detergent to clean the tread belt. Do not use
excessive water and avoid leakage to the electrical components and underneath the
running belt
• Disconnect the power cord when the WalkSlim 920 will not be used for a long time.
• Do not store the treadmill in the bathroom or outside and avoid areas with a lot
of moisture.
Tread Belt Adjustments
While each treadmill tread belt has been finely adjusted, after transport and installation
it may need to be adjusted. Adjustment may also be required throughout the life of the
treadmill. Reasons for this may be:
1. The treadmill has been on an uneven surface.
2. When in operation, the user walks / runs unevenly (to one side) on the belt.
3. The users on the treadmill have different physical weight and force.
A tread belt deviation may seriously damage the tread belt, so must be corrected once
noticed.
PLEASE NOTE: Correct maintenance of the treadmill is important. Issues arising from
ongoing tread belt misalignment will not be covered under warranty.
How to adjust alignment on left side:
tighten the bolt (clockwise) on the left side
if the belt is deviating to left side or loosen
bolt on the right side (counter clockwise).
How to adjust alignment on right side:
tighten the bolt (clockwise) on the right
side if the belt is deviating to right side
or loosen bolt on the left side (counter
clockwise).

EN
13
Motor Belt Adjustments
While each treadmill motor belt has been finely adjusted, after transport and installation
it may need to be adjusted again and also throughout the life of the treadmill.
Adjustment Steps:
1. Adjust the balance of the motor
with an allen key. Turn the bolt
half a turn counter clockwise.
2. Turn the belt tightening bolts
clockwise half a circle.
NOTE: Clean belt and pulley
grooves regularly.
WARNING
Unplug the treadmill before performing maintenance.
Front Roller
Belt tightness
bolts
Motor balance
adjustment
bolts
Motor
Belt

Troubleshooting
The treadmill is
not working
•Make sure the power cord is properly secured into the power
outlet and that the switch is turned to the ‘ON’ position.
•Check the Safety Key is inserted in the correct position.
The tread belt is
not working
• Insufficient lubrication. Add silicone oil lubricant.
• Tread belt is too tight. This will reduce motor performance
and increase wear of rollers and tread belt. Adjust tread belt
tightness to the correct tension. The tread belt should be able
to be lifted from the base by about 5-7.5cm by hand
The tread belt is
slipping
•Tread belt is too loose or too tight. Adjust the tread belt
tightness.
•An example of when the belt is too loose is when you have
pressed the Function Dial to stop the treadmill and the tread
belt begins to slip instead of uniformly slowing down. Adjust
the tightness of the tread belt by using the Allen Key and turn
180 degrees at a time on both sides of the treadmill. Do not
overtighten the tread belt as it will increase the load on the
motor and may cause damage to motor, tread belt and roller.
The Treadmill will
not speed up or
slow down
• Please contact our Customer Service Centre.
The Touch Screen
does not work
• Please contact our Customer Service Centre.
The Treadmill is
losing speed
• Add lubricant oil to the underside of the tread belt as per
instructions on page 7 of this manual.
Touch Screen
is on but the
Treadmill does
not start
• The treadmill has not been started according to the
instructions on pages 7-11 of this manual. If the treadmill still
does not start please contact our Customer Service Centre.
Unreadable /
Incoherent Touch
Screen
• Motor is overheating. Turn the power off, unplug and leave for
one hour then restart. If it does not restart please contact our
Customer Service Centre.
EN
14

EN
15
The belt is
running to the left
1. Tighten the bolt clockwise on the left side or loosen bolt on
the right side counter clockwise using the Allen Key.Start the
WalkSlim 920 to check the new position of the belt.
2. If the belt is still not in the middle repeat the action until
adjusted to a central middle position.
3. After adjusting the belt to the middle, start the WalkSlim 920,
set to the maximum speed and observe the tread belt to
ensure that is running smoothly. If it’s not centralised, then
repeat the adjustment steps again.
The belt is
running to the
right
1. Tighten the bolt clockwise on the right side or loosen bolt on
the left side counter clockwise using the Allen Key.
Start the WalkSlim 920 to check the new position of the belt.
2. If the belt is still not in the middle repeat the action until
adjusted to a central middle position.
3. After adjusting the belt to the middle, start the WalkSlim
920, set to the maximum speed and observe the tread belt
to ensure that is running smoothly. If it’s not centralised, then
repeat the adjustment steps again.
The belt is
skidding
• Turn the left and right screw half a turn clockwise at the same
time and then repeat the adjustment until running normally.
Do not tighten the screw excessively.
WiFi Indicator Status
Status Description Light mode
Waiting for fast connection Slow flashing
In fast connection,
In network connection,
In re-connection
Fast flashing
Successfully connecting to the cloud Normally on
Upgrading Double flashing

EN
16
Error Message Codes
Error
Code Fault Description Solution
E0 Communication
Issue
Unplug the WalkSlim 920, leave for several minutes
and then restart. If it does not restart please contact
our Customer Service Centre.
E02 Stall Protection Turn the power off, unplug and leave for one hour
then restart. If it does not restart please contact our
Customer Service Centre.
E03 Speed Sensing
Failure
Turn the power off, unplug and leave for one hour
then restart. If it does not restart please contact our
Customer Service Centre.
E05 Overcurrent
Protection
Turn the power off, unplug and leave for one hour
then restart. If it does not restart please contact our
Customer Service Centre.
E06 Motor Issue Please contact our Customer Service Centre.
E10 Output Short
Circuit
Please contact our Customer Service Centre.
E13 Communication
Issue
Please contact our Customer Service Centre.

EN
17
ABODEFIT HEALTH™ WALKSLIM 920 WARRANTY
Warranty Period: Lifetime Frame, 5 Years Motor, 2 Years Parts & Labour. Vitality 4 Life are the warranty
providers for AbodeFit Health™ products. Vitality 4 Life warrant this product to be free from defects in
materials and workmanship while in normal domestic use for a period of five years on the motor and two
years on other parts (with the exception of a life warranty on the frame) from the original date of purchase.
DO NOT RETURN THE PRODUCT TO THE STORE.
LODGING A WARRANTY CLAIM
Should you experience any issues with your product, please follow
these steps to lodge a warranty claim:
1. Contact your local Vitality 4 Life Service Centre with the
following details: Your warranty details including name, email
and phone number
– Product name and model number
Product serial number, found on the rating label of the
product
Explanation of how the damage occurred
Photos of the damage or issue is highly beneficial to
expediting your claim
2. Vitality 4 Life will assess your claim and respond within 24-48
hours.
3. In the event the product is required to be sent to the Service
Centre, the customer is liable for all packing, freight and
insurance costs for transit of the product to Vitality 4 Life.
Subject to the applicable consumer laws in your jurisdiction.
4. If the product, or one of its parts, qualifies for replacement or
service within the 30-Day period after date of purchase, Vitality
4 Life will arrange the shipping at no cost to you.
5. Any product sent to a Vitality 4 Life Service Centre must include
a Return Authorization Form. Failure to include this form may
result in the product being rejected from our warehouse or a
delayed service time.
6. Vitality 4 Life will contact you with a quote prior to undertaking
any service work outside of the warranty coverage.
7. Typical turn-around times to address warranty claims can be
between 10-14 business days, plus shipping, depending on
location and type of damage or warranty claim.
TERMS OF PRODUCT WARRANTY COVERAGE
Vitality 4 Life provides the Product Warranty coverage as further
described below and limited to the terms and conditions hereof:
1. If the Product exhibits a defect while in normal domestic use,
within the warranty period; we will, at our option, either repair
or replace the product or defective part free of charge. The
Product must be delivered by insured mail, in proper packaging
to your Service Centre as indicated on the back of the manual
as a condition to any warranty service obligation.
2. In the event that the warranty period for a product has expired,
or if a Product does not qualify for warranty service, repair
or replacement, consumers may still buy replacement parts
or have products repaired by one of Vitality 4 Life’s Service
Centres. Please contact Vitality 4 Life for further information.
3. Do not send the product back to the Service Centre without a
Return Authorization Form.
4. In no event shall our liability exceed the retail value of the
product. We make no warranty with respect to parts, from a
source other than Vitality 4 Life.
5. In the event that warranty parts or products are provided, the
customer must cover the related shipping costs to receive
goods.
6. All exchanged or substitute parts and products replaced
under warranty service will become the property of Vitality
4 Life. Repaired or replaced products or parts thereof will
be warranted by Vitality 4 Life for the balance of the original
warranty period.
7. (Australia only) Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
WARRANTY DOES NOT COVER
1. Damage, accidental or otherwise, to the Product, not caused by
direct defect in factory workmanship or materials.
2. Damage due to abuse, mishandling, alteration, misuse,
commercial service, tampering, accident, failure to follow care,
operating and handling provisions indicated in the instructions.
3. Damage caused by parts or service not authorized or
performed by Vitality 4 Life.
4. ‘Normal’ wear and tear that naturally and inevitably occurs as a
result of normal use or aging.
5. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Therefore, the above
limitations may not apply to you in the case of damage
in shipment. If your product was damaged in shipment:
Immediately report this type of damage to the parcel carrier
and have them file an inspection report to contact the
distributor from whom you purchased the product for further
instructions.
6. You have rights and benefits under the consumer laws in
your jurisdiction. Without detracting from these rights or
benefits, Vitality 4 Life excludes all liability in respect of this
product for any other loss which is not reasonably foreseeable
from a failure of this product, which may include liability for
negligence, loss of expenditure associated with the product and
loss of enjoyment.

Support & Service Centres
Contact your local distributor for warranty & service
Vitality 4 Life – Australia & New Zealand
E: [email protected]
W: www.vitality4life.com.au
Vitality 4 Life – United Kingdom
E: [email protected].uk
W: www.vitality4life.co.uk
Vitality 4 Life - United States
E: [email protected]
W: www.vitality4life.com
Vitality 4 Life – France
E: [e-mail]
W: www.vitality4life.fr
Vitality 4 Life – Deutschland
E: [email protected]
W: www.vitality4life.de
Vitality 4 Life – Italia
E: [e-mail]
W: www.vitality4life.it
Vitality 4 Life – España
E: [e-mail]
W: www.vitality4life.es
Vitality 4 Life – Netherlands
E: [e-mail]
W: www.vitality4life.co.nl