ABSTRACTA Plenty Pod Medium User manual

Plenty Pod
Assembly Instruction

Including the following screws and fasteners
for Plenty Pod Medium
Pos
Art.nr
Pcs
Description
1
575 046 04
26
4,2 x 25 screw with drill bit
2
575 045 04
14
4,2 x 14 screw with drill bit
3
377 001 01
6
UP-bracket (pairs, right-left)
4
54342146
10
Distance plate
5
537 063 04
7
U-rail connector
6
534 195 60
1
Cable lead-through

Required tools
Spirit-level
Screwdriver
Ratchet
Bit set, Ph, Torx, Insex
Rubber hammer

Mounting
Start with evening out the floor module which you want to
set up your pod on.
(An uneven floor can especially complicate mounting the glaswalls
and fitting in the door)

Do not screw the Plenty Pod into the floor ifitcontains floor
heating, electric cables, water pipes orthe like. PlentyPod
stands stable without fixing.
If you need toattach Plenty Pod to the floor, use the
appropriate screw andplug. Not included.
Place the U-rails according to picture below
Connect the U-rails and corners with U-rail connector. Only
between U-rails and corners, not for threshold.

Place the distance plate according to picture.
U-rail
connector

Distance Plate

Place the premounted wall module with the first
Continue with the first set of separate bottom frame profiles
as follows:

Loosen the set screw in the frame profile (Fig A)until the
hammerhead bolt (Fig B) at the end ofthe profile can beturned
andfit into the middle track of the vertical profile (Fig C).
When the hammerhead bolt isinserted into thetrack, place the
profile onthe floor (Fig D). Then tighten the set screw until the
profile is fixed to thevertical frame (Fig E).
The edge ofthe profile should align with the outer edge of the
floor. Repeat with the profile on the opposite side.
Fig A Fig B Fig C
Fig D Fig E

Alternatingly mount the separate vertical and horizontal
profiles onto each other until the whole rail is filled.

From the top, place the threshold between the vertical
profiles, by sliding the attached L-bracket into the tracks.
Drag it down to the floor.
Squeeze the vertical profiles together so that there is no gap
between them and the threshold.

Fixate the L-profile in the vertical profiles.
Mount the top horizontal profiles between the vertical
profiles.

Placement of profiles
Socket
Left top and bottom
horizontal profile
Right top and bottom
horizontal profile
Front horizontal
profile
Central pillar
Central pillar
Seperate vertical
profils
Threshold

Fabric wall mounting
Find out which walls are going to have fabric, respectively glasses.
For fabric walls, mount the vertical and horizontal L-profile profiles as shown
below.
L-profile
2 pcs 2038 mm
2 pcs 970 mm
L-profile is mounted with screw
(575 045 04, 4,2x14).
Start with the vertical L-profiles,
then the horizontal.
L-profiles (pointing inwards)
Horizontal
frame profile

Mount the UP-brackets (377 001 01).

Place the acoustic walls inside,
behind the L-profiles.

Outside wall panels
Begin at the top by hooking
the track of the L-profile onto
the UP bracket (377 001 01).
The lower part of the wall
panel should hang loosely.
377 001 01
Push the wall panel to the
frame without connecting it
to the bottom.

Press straight from below on the wall panel,
right up. Push the wall panel against the frame
and let it fall down and connect to UP brackets.
Press down the panel. Make sure it is
hooked into all 6 UP brackets.

Mounting glass walls
Find out which walls are going tohave fabric or glasses. Start by tucking the
inside vertical glass wall profiles into the vertical frame profiles. (Fig A). Then
take the inside horizontal glass profiles into the horizontal frame profile (Fig B).
The rubber seal should be placed in the center ofthe profile (Fig B), where the
glass shuold be placed.
Fig A
Fig C
Fig B