Abus TVCC71000 User manual

19
Vandal proof WD DNR Day/Night Vario
650 TVL outdoor dome camera
Version 12/2010
Original English user manual. Keep for future use.
TVCC71000
TVCC71500

20
Ŝ
Introduction
Dear Customer,
Thank you for purchasing this product.
This product meets the requirements of the applicable European and national guidelines.
The corresponding declarations and documents can be obtained from the manufacturer
(www.abus-sc.com).
To maintain this condition and to ensure risk-free operation, you as the user must observe these
operation instructions!
Before initial start-up, read through the complete operating instructions observing operating and
safety instructions.
All company and product names mentioned in this document are registered trademarks.
All rights reserved.
If you have any questions, please contact your installer or your local dealer!
Disclaimer
This user manual was prepared with greatest care. If you should notice omissions or inaccuracies,
please inform us about these on the back of this manual given address.
The ABUS Security-Center GmbH & Co. KG assumes no liability for technical and typographical
faults and reserves the right to make at any time modifications to the product or user manual
without a previous announcement.
The company is not liable or responsible for direct and indirect subsequent damages which are
caused in connection with the equipment, the performance and the use of this product.
No guarantee for the content of this document is taken.

21
Important safety instructions
The warranty will expire for damage due to non-compliance with these operating
instructions. We shall not be liable for any consequential loss!
We do not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety-instructions. In such cases the warranty will
expire.
Dear customer,
The following safety instructions are intended not only for the protection of your health, but also for
the protection of the device. Please read through the following points carefully:
xThere are no parts on the inside of the product which need to be serviced. Apart from this, the license
(CE) and the guarantee/warranty will lapse if you open/take the product apart.
xThe product will be damaged even it falls from a low height.
xThis device can be used in inside as well as outside.
xDuring the installation of the camera please take care that direct sunlight cannot fall onto the image
sensor of the device. Please follow the installation instructions in the corresponding chapter of this
user manual.
Avoid using the device under the following unfavorable ambient conditions:
xwetness or excessive air humidity
xextreme cold or heat
xdirect sunlight
xdust or combustible gases, vapors or solvents
xstrong vibration
xstrong magnetic fields, such as those found in the vicinity of machinery or loudspeakers
xthe camera should not positioned with opened iris towards the sun - this can lead to the
destruction of the sensor.
xthe camera may not be installed on unstable surfaces
General safety instructions:
xDo not leave packaging material lying around carelessly. Plastic/ foil/bags and polystyrene parts etc.
could become dangerous toys for children.
xFor safety reasons don’t give the camera into child hands due to them being able to swallow small
parts.
xPlease do not insert objects through the openings into the device.
xUse only accessories which are specified by the manufacturer.
Please do not connect incompatible parts to the device.
xPlease pay attention to the safety instructions and user manuals of the other connected devices.
xCheck the device for damages before installation. If this should be the case please do not use it.
xPlease adhere to the operational voltage limitations listed in the technical data. High voltage could
destroy the device and pose a health hazard (electric shock).
During the installation into an existing video surveillance system make sure that all devices are
disconnected from the low and supply voltage circuit.
If in doubt allow a professional electrician to mount, install and wire-up your device. Improper or
make-do electrical connection to the mains does only represent at threat to you but also to other
persons.
Wire-up the entire system making sure that the mains and low voltage circuit remain separated
and cannot come into contact with each other in normal use or due to any malfunctioning.

22
Table of contents
1. INTENDED USE.......................................................................................................................23
2. EXPLANATION OF SYMBOL..................................................................................................23
3. SCOPE OF DELIVERY ............................................................................................................23
4. FEATURES AND FUNCTIONS................................................................................................23
5. DESCRIPTION OF DEVICE.....................................................................................................24
5.1 OVERVIEW –ITEM NUMBERS .....................................................................................................24
5.2 UNPACKING..............................................................................................................................24
6. MOUNTING ..............................................................................................................................24
6.1 CABLE ROUTING .......................................................................................................................24
6.2 MOUNTING OF THE CAMERA ......................................................................................................24
6.3 CONNECTORS...........................................................................................................................26
6.4 CAMERA MODULE ADJUSTMENT.................................................................................................26
6.5 FOCUS AND ZOOM ADJUSTMENT................................................................................................27
6.6 ADJUSTMENT OF IR LED INTENSITY AND CAMERA PARAMETER...................................................27
6.7 CAMERA PARAMETER (OSD MENU) ...........................................................................................28
7. SERVICE AND CLEANING .....................................................................................................32
7.1 FUNCTION TEST........................................................................................................................32
7.2 CLEANING ................................................................................................................................32
8. DISPOSAL ...............................................................................................................................32
9. TECHNICAL DATA..................................................................................................................33

23
1. Intended use
The vandal proof 650TVL outdoor dome camera is equipped with a high quality image sensor. It is
used for video surveillance in connection with a recorder or monitor.
You can find a detailed description of functions in section “4. Features and functions”.
Any other use than that described above can lead to damage to the product and in
addition involve other risks. This does not include operation for other applications
and would in case of doing so the guarantee and any related liability will lapse. This
is also the case if any unauthorized changes or additions have been made to the
product.
Please read through the entire manual carefully before putting this product into
operation. This operating manual contains guidelines that are important for correct
mounting and operating.
2. Explanation of symbol
A flash in the triangle is used if there is danger for the health, e.g. by an electric shock.
An exclamation mark in the triangle points to an important note in this user manual
which must be minded.
This symbol can be found when you are to be given tips and information on operation.
3. Scope of delivery
x650 TVL Outdoor dome camera
xInstallation material (screws, pegs)
xDC 2-pin adapter
xUser manual
4. Features and functions
xState-of-the-art EFFIO chip set with WD function for clear images, even at high contrast
ratios
xDNR function for noise-free images
xIntegrated 2.8 - 10.5 mm variofocal lens
xHigh resolution of 650 TV lines
xEasy Plug camera module and mounting plate for quick installation
xTriaxial camera holder
xIP66 protection class for outdoor use
xAuto-IR LED function for automatic adjustment of the LED performance (TVCC71500)

24
5. Description of device
5.1 Overview – item numbers
Item number TVCC71000 TVCC71500
Resolution 650 TVL 650 TVL
Lens 2.8~10.5 mm 2.8~10.5 mm
IR -

Day/Night
(removable IR cut
filter) 
Voltage 12 VDC 12 VDC
5.2 Unpacking
While you are unpacking the device please handle it with utmost care.
If you notice any damage of the original packaging, please check at first the device.
If the device shows damages, please contact your local dealer.
6. Mounting
Attention!
Please disconnect the camera from power supply during the installation.
6.1 Cable routing
The cable can be routed to side (visible) or through the bottom side (hidden). To prevent from
wetness a cable gland will be installed on the housing. Please fully screw the cable gland into the
side or bottom opening, the remaining opening will covered by a flat supplied screw.
6.2 Mounting of the camera
Please remove the dome head ring first by anti-clockwise
rotation.
Then unscrew the fixing screws for the dome head and
remove it.

25
For this camera type the camera module can be
removed, and it is fixed by two fixing screws. Base part
of the camera and camera module are connected by a
15 pin D-Sub joint. Unscrew the fixing screws, and
carefully remove the camera module.
Place the base part to the desired installation
position, mark the holes for fixing on the
surface, and drill the fixing holes. Use the
supplied screws and pegs to fix the base part on
the surface. The cable rounting can be done to
the side or throught the base.
Installation of the camera module
Bring the camera module close to the base
part so that the 15 pin socket and plug
position will match. At the opposite side of the
15 pin joint the module will be hold in position
by two fixing bars. In case socket and plug will
match please press the camera module on
both outside handles in direction of the base
part, until the 15 pin joint is fully latched.
Please screw the two fixing screws for the
camera module back.
Installation of the dome head
First please perfom the steps of adjustment of
viewing angle of the camera module as well
as the adjustment of the lens.
The dome head will be fixed on the dome
base by three screws. Please take care that
the dome head will placed even to the dome
base. The dome head ring will be fixed by
clockwise rotation to the dome head.

26
6.3 Connectors
Before you start with the installation please make sure that the supply voltage and the nominal
voltage of the camera comply together.
Power supply & video signal Video output (for service purpose)
1 Video output (primäry), BNC (female), FBAS 1Vs-s
2 Power connector (round plug 5.5x2.1mm, 12 VDC) or DC 2-pin adapter
3 Videoausgang (sekundär, Service), Cinch (female) FBAS 1Vs-s
6.4 Camera module adjustment
The camera module can be adjusted in 3 axis. The adjustment of the third axis often will be used on
wall mount of the camera. The module rotation (1st and 3rd axis) must not be performed more than
360 degree.
Pan (1st axis)
Tilt (2nd axis) Rotation (3rd axis)
1
2
3

27
6.5 Focus and zoom adjustment
The cameras TVCC71000 and TVCC71500 are
equipped with a vario focal lens. On the bottom side of
the lens two adjustment handles for focus and zoom
ratio are positioned. The handles additionally act as a
fixing screw for the focus and zoom adjustment.
The fixing handles can be rotated anti-clockwise for defixing. Please perfom this with care to
prevent the handles falling off the lens. Now please adjust zoom ratio and focus. Afterwards fix the
handles by rotating clockwise.
Function Beschreibung / Option
Zoom ratio adjustment WIDE – Viewing angle wide, Zoom 0x (max.)
TELE – Viewing angle narrow, Zoom 3.75x (max.)
Focus adjustment FAR – Focus far
NEAR – Focus near
6.6 Adjustment of IR LED intensity and camera parameter
1 IRIS ADJ.: Adjustment of the aperture of the auto iris lens
2 IR intensity: 2 levels for the IR light intensity are available (HI – 20 meter; LOW – 10 meter).
3 Setup of camera parameter over control keys (OSD menu)
TVCC71000:
TVCC71500:
1
2
3
1
3

28
6.7 Camera parameter (OSD menu)
SETUP MENU
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST 
ATR ON
PRIVACY OFF
NR 
CAMERA ID OFF
CAMERA RESET
EXITSAVE ALL
Funktion Beschreibung
WHITE BAL Settings for White balance function
BACKLIGHT Settings for back light handling
PICT ADJUST General image settings
ATR Adaptive Tone Reproduction – Settings for the Wide Dynamic
Function
PRIVACY Settings for privacy masking
NR Settings for noise reduction
CAMERA ID Setting for camera description
CAMERA RESET Restore the default settings
EXIT Leaving the OSD menu
SAVE ALL Save all changed values

29
White Balance (WHITE BAL)
Function Description
ATW Auto Tracking White Balance
The setting for the white balance function will be performed
dynamically and continuously in the range of 1800~10500K.
PUSH Continuous setting for the white balance with limitation of color
temperature range
USER1 / User 2 User defined white balance
B-GAIN (0~255): Blue value
R-GAIN (0~255): Red value
ANTI CR Optimized white balance settings for fluorescent light, to avoid
cross color effects
MANUAL Manual white balance
B-GAIN (0~255): Blue value
R-GAIN (0~255): Red value
PUSH LOCK Push Lock
The white balance measurement will be performed by pressing
the „Enter“ button on the control board, and will be stored.
BACKLIGHT
Function Description
OFF The back light handling is turned off.
BLC The conventional back light compensation function is activated.
(Back Light Compensation)
HLC The function for inversion of too bright image areas into black
color is activated (High Light Compensation). Too bright image
areas will be converted to black areas over certain value (e.g.
car lights).
PICT ADJUST
Function Description
MIRROR Horizontal mirror
OFF: Horizontal image inversion is deactive
ON: Horizontal image inversion is active
BRIGHTNESS Brightness (0~255)
CONTRAST Contrast (0~255)
SHARPNESS Sharpness (0~255): A high value of sharpness could increase
the noise level.
HUE Hue (0~255)
GAIN Gain (0~255): Setting for the maximum internal gain
value.

30
ATR
Function Description
ATR Settings for the Wide Dynamic Function (Adaptive Tone
Reproduction)
OFF: Wide Dynamic Function deactive
ON: Wide Dynamic Function active
LUMINANCE (LOW/MID/HIGH):
Level of the brightness balance. Dark areas will be
displayed more bright (LOW->HIGH), in addition the
brightness for bright areas will be tried to keep constant.
CONTRAST (LOW/MIDLOW/MID/MIDHIGH/HIGH)
Increasing of image contrast
(LOW->HIGH). A high value can cause detail loss in
dark areas as well as over exposure.
PRIVACY
Function Description
PRIVACY Privacy masking function of up to four zones (free to
configure)
OFF: Privacy masking function deactive
ON: Privacy masking for all four zones is active
AREA SELECT (1/4~4/4): Zone selection
TOP (0~288): Top limit for the selected area
BOTTOM (0~288): Bottom limit for the selected area
LEFT (0~468): Left limit for the selected area
RIGHT (0~468): Right limit for the selected area
COLOR (1~8): Red(1), light green(2), blue(3),
green(4), light blue(5), purple(6),
white(7), black(8)
TRANSP (0.0~1.00): Transparency of the masking
MOSAIC (OFF/ON): Mosaic display for the privacy
masking. The impression of
unsharp areas will be produced
for masked areas. The effect is
at best at TRANSP=0.00.
RETURN: Back to main menu

31
NR
Function Description
NR Settings for the noise reduction (2D DNR)
OFF: Noise reduction deactivated
NR MODE (Y/C/ Y/C):
Y: Noise reduction for luminance signal
C: Noise reduction for chroma signal
Y/C: Combination of Noise reduction for luminance and
chroma
Y LEVEL (0~15): Level for the noise reduction of luminance
C LEVEL (0~15): Level for the noise reduction of chroma
RETURN: Back to main menu
Camera ID
Function Description
CAMERA ID Camera description
OFF: No display of the camera description in the live image
ON: Display of the camera name, with dedicated location
The camera description length is max. 26 digits.
monp: Control keys for this sub menu
CLR: By selection and pressing the Enter key, the selected
digit will be deleted.
POS: By pressing the Enter key, the positioning mode will be
activated. Use the control keys to change the position of
the name. By pressing Enter once again, the sub menu
will be left.
CAMERA RESET
Function Description
CAMERA RESET Restore the default camera settings

32
7. Service and cleaning
7.1 Function test
Check the technical safety of the product such as damage to the housing at regular intervals.
When it can be assumed that the safe operation is no longer possible, the product must be put out
of service and precautions taken o ensure that it is not used unintentionally.
It must be assumed that safe operation is not longer possible if
xthe device shows visible signs of damage
xthe device no longer operates and
xhas been stored for longer periods under unfavorable conditions or
xhas been subjected to considerable stress in transit.
Please note:
The product is absolutely maintenance-free for you. There are no components on the
inside of the product to be checked or services by you, never open it.
7.2 Cleaning
Clean the product with a clean, soft cloth. To remove severe contamination, the cloth can be
dampened with luke-warm water.
Make sure that no liquids can enter the equipment as the device can be destroyed.
Never use chemical detergents as they could attack the surface of the device.
8. Disposal
Products which are labeled with this pictogram may not be disposed by the
domestic rubbish. Please dispose the product in accordance with the prevailing
legal regulations at the end of its life time.
Please consult your dealer or dispose the product over the municipal gathering
point for electric scarp.

33
9. Technical data
Item number TVCC71000 TVCC71500
TV standard PAL
Resolution 650 TVL
Bildaufnehmer 1/3‘‘ Sony Exview HAD II CCD
DSP Sony Effio-E
Picture elements (total) 1020(H) x 596(V)
Picture elements (effective) 976(H) x 582(V)
Signal-to-noise ratio 50 dB
Minimum illumination (day) 0.05 Lux @ F1.2 0.05 Lux @ F1.2
Minimum illumination
(night) 0 Lux @ F1.2 (external IR) 0 Lux @ F1.2
Day/night IR cut filter removable
(ICR), Color / B/W IR cut filter removable (ICR), Color / B/W
Lens 2.8~10.5mm, F1.2 2.8~10.5mm, F1.2
IR LEDs - 24 LEDs, 850nm
IR Range - 10 / 20 m
Horizontal angle of view 101.8°~27.4° 101.8°~27.4°
Electronic Shutter AI AI
Synchronisationi Internal
Automatic gain control
(AGC) 28 dB (max.)
Backlight compensation
(BLC) BLC
WDR Max. 46 dB
Noise reduction 2D DNR
White balance ATW, 1800K~10500K
Control options OSD OSD
Protection class IP66
Video signal 2 x FBAS, 1V s-s, 75 Ohm (BNC, Cinch), 5.5x2.1mm (DC)
Operating temperature -10°C ~ +50°C
Humidity 0~85%, not condensing
Nominal supply voltage 12 VDC
Power consumption max. 250 mA max. 350 mA (IR off),
max. 450 mA (IR on)
Dimension (HxØ) 99.5 x 145 mm
Weight 700 g 700 g
Certifications CE, RoHS, Reach

34