AC Infinity AC-CTC7 User manual

CO2CONTROLLER
ENVIRONMENTAL MONITOR
USER MANUAL

3
WELCOME
Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service.
If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com
and click contact for our contact information.
EMAIL
[e-mail]
WEB
www.acinfinity.com
LOCATION
Los Angeles, CA

4
PRODUCT
CO2CONTROLLER
MODEL
AC-CTC7
UPC-A
819137022997
MANUAL CODE CTC2210X1

5
MANUAL INDEX
Manual Index .................................................................................
Product Warning ............................................................................
Key Features .................................................................................
Product Contents ...........................................................................
Powering and Setup........................................................................
Programming .................................................................................
Other Settings ................................................................................
Other AC Infinity Products .............................................................
Warranty ........................................................................................
Page 5
Page 6
Page 7
Page 8
Page 9
Page 12
Page 25
Page 26
Page 27

6
Ensure your power source conforms to the electrical requirements of this product.
Check your local code restrictions for additional safety measures that may be needed for a
proper code compliant installation.
Read all instructions before installing and using this product.
When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other
hidden utilities.
If you are unfamiliar or have doubts about performing this product’s installation, seek the
services of a qualified, trained, and licensed professional. Inappropriate installation will void
this product’s warranty.
This product must not be used in potentially hazardous locations such as flammable,
explosive, chemical-laden or wet atmospheres.
Do not cover power cords with rugs or other fabric materials.
Do not depend on the on/off programming as the sole means of shutting power from this
product. Unplug the power cord before installing, servicing, or moving this product.
Do not operate this product while its cord is damaged, or if it malfunctions, has been dropped,
or is damaged in any manner.
Use this product only as intended by the manufacturer.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
PRODUCT WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:

7
KEY FEATURES
ACTIVE MONITORING
LED display shows key data
like outlet power status, CO2
trends, clock, and cycle.
WALL MOUNTING
Hard black housing and
fire-resistant casing with key-
hole hanger for easy mounting.
SMART CONTROLLER
Features automation controls
that power and activate your
outlet devices featuring CO2,
fan, and cycle programming.
DUAL OUTLETS
Built with a detached electrical
socket module that allows for
powering and controlling two
individual devices.
CUTTING EDGE SENSOR
Next-generation sensor using
photoacoustic technology to
accurately read CO2levels.
EXTRA CORD LENGTH
Extended cord length of 144
inches (12 feet) for ease of
management and flexible
mounting options.

8
PRODUCT CONTENTS
WALL-HANG
WOOD SCREWS
(x3)
WIRE
MOUNT
(x1)
CO2
CONTROLLER
(x1)
CO2
SENSOR
(x1)

9
POWERING AND SETUP
STEP 2
Insert the power plug into a wall outlet to power
your controller.
STEP 1
Plug the sensor probe into the 3.5mm port
located at the bottom side of your controller.

10
POWERING AND SETUP
STEP 4
Locate a spot free of obstruction and secure the
anchor into your wall. Twist the wood screw into
the anchor.
STEP 3
Secure the corded sensor using the included
wire tie and adhesive mount.
You may also wall hang the corded sensor. Refer
to the next steps for wall hanging instructions.

11
STEP 5
Hang your controller by the screw using the
hole located on its backside.
POWERING AND SETUP
STEP 6
Plug your fan and/or CO2generator (not included)
into the sockets to power it with your controller.

12
1. OUTLET BUTTON
Switches between Outlet 1 and Outlet 2. Set programs will still be active regardless of your
current outlet.
PROGRAMMING
2. MODE BUTTON
Cycles through each of the controller’s modes: OFF, ON, CO2(Center and Zone), Fan (Center and
Zone), and CYCLE (On and Off).
4. SETTING BUTTON
Cycles through each of the controller’s settings: CO2CHART, NIGHT1 (Start and End), NIGHT 2
(Start and End), ALARM HIGH, ALARM LOW, DISPLAY BRIGHTNESS, CLOCK, CALIBRATION.
3. UP/DOWN BUTTONS
Adjusts the value of your current mode. The up button increases and down button decreases the
setting. Hold both to reset values to factory settings.
1 2 3 4
5 6 7
10
11
8
12 13
9
5. OUTLET STATUS
Displays the devices’ active status, ON or OFF, indicating whether or not power is being fed.

13
6. STATUS ICONS
Flashes or displays the alert icons of the controller. The icons include ALARM, TIMER ALERT, and
DISPLAY LOCK.
7. CURRENT TIME
Displays the current time. The internal battery sustains the clock so it does not default to 00:00 if
power is cut off. See page 22 to learn how to set the clock time.
PROGRAMMING
8. CO2CHART
Displays CO2levels over a set period, adjustable in controller settings (see page 19). Also displays
minimum and maximum PPM levels based on the current time scale.
9. TARGET ZONE ARROWS
Indicates whether the current CO2reading is within range of your center and zone programming.
10. SENSOR READING
Displays current CO2levels measured within a 0-5000ppm range. Changes in 1ppm units when
under 1000ppm, 5ppm units when in between 1000-2000ppm, and 10ppm units when over
2000ppm. Trend indicator signals a rise, steady, or fall in CO2levels within the last hour.
11. CURRENT MODE
Displays the current mode, CO2or FAN, indicating which mode your outlet is in.
12. CENTER SET POINT / COUNTDOWN
Displays the countdown of the TIMER TO ON, TIMER TO OFF, CYCLE, or SCHEDULE modes. TO
ON shows the amount of time left before your devices power on. TO OFF shows the amount of time
left before your devices power off.
13. ZONE VALUE / USER SETTING
Displays the value of your current mode. Use the up and down buttons to adjust the value.

14
OUTLET TOGGLING
Pressing the outlet button switches between the controller’s two devices: Outlet 1 and Outlet 2. The
dot indicates the controller’s current device.
OUTLET 1 & OUTLET 2
Navigate to a numbered outlet with a device
plugged in to set individual programming.
Programs will run in the background even while
you navigate to the other outlet.
PROGRAMMING

15
CONTROLLER MODES
Pressing the mode button will cycle through the controller’s available programming modes: OFF,
ON, CO2(Center and Zone), Fan (Center and Zone), and CYCLE (On and Off). Make sure to use
the appropriate mode for the device you’ve plugged in (ex. CO2mode for CO2generator).
ON MODE
Your device(s) will switch on regardless of CO2
levels or time-based triggers.
OFF MODE
Your device(s) will switch off regardless of CO2
levels or time-based triggers.
Jump back to OFF Mode anytime by holding the
MODE button while in other modes or settings.
PROGRAMMING

16
STEP 1
Ensure you are in the correct numbered outlet for the CO2
generator you are using. Then navigate to the Center submode.
STEP 2
Use the up or down buttons to set the center
value and your desired CO2level. Press the mode button to
navigate to the Zone submode.
STEP 3
Use the up or down buttons to set the zone value and establish
an activation buffer around the center value.
Your CO2generator will switch on if the reading falls below this
threshold. When the reading rises above this trigger point, your
CO2generator will switch off.
In this example, the center value is 1200ppm and the zone
value is 400ppm.
Your CO2generator will switch on when the current CO2level is
below 1000ppm [1200 – (400/2)].
The CO2generator will turn off when the current CO2level is
above 1400ppm [1200 + (400/2)].
The set zone value is the
buffer around your set center
value that is equal to half its
setting. (ex. 400ppm. Buffer
zone is 1000-1400ppm).
PROGRAMMING
CO2MODE
CO2MODE
ON
CO2MODE
OFF
ZONE (400ppm)
THRESHOLD
CENTER (1200ppm)1000ppm 1400ppm

17
STEP 1
Ensure you are in the correct numbered outlet for the fan you
are using. Then navigate to the Center submode.
STEP 2
Use the up or down buttons to set the center value and
high CO2trigger. Press the mode button to navigate to the
Zone submode.
STEP 3
Use the up or down buttons to set the zone value and establish
an activation buffer around the center value.
Your fan will switch on if reading meets or exceeds this
threshold. When the reading falls below this trigger point, your
fan will switch off.
In this example, the center value is 1500ppm and the Set Zone
is 1000ppm.
Your fan will switch on when the current CO2level meets and
exceeds 2000ppm [1500 + (1000/2)].
The fan will turn off when the current CO2level is below
1000ppm [1500 - (1000/2)].
The set zone value is the
buffer around your set center
value that is equal to half its
setting. (ex. 1000ppm. Buffer
zone is 1000-2000ppm).
PROGRAMMING
FAN MODE
FAN MODE
ON
FAN MODE
OFF
ZONE (1000ppm)
THRESHOLD
CENTER (1500ppm)1000ppm 2000ppm

18
CYCLE MODE (ON AND OFF)
Sets an ON duration and an OFF duration for
your device to cycle through continuously. Press
the up or down button to set a countdown for
your device to turn on. Then press the mode
button and use the up or down button to set a
countdown for your device to turn off.
The countdown will begin if no buttons are
pressed for 5 seconds. Leaving the CYCLE
mode while the countdown is running will pause
it until you return to this mode.
PROGRAMMING

19
PROGRAMMING
CONTROLLER SETTINGS
Cycles through each of the controller’s settings: CO2CHART, NIGHT1 (Start and End),
Night 2 (Start and End), ALARM HIGH, ALARM LOW, DISPLAY BRIGHTNESS, CLOCK,
and CALIBRATION.
CO2CHART SETTING
Changes the CO2chart’s time scales. Each
scale adjusts the chart to the selected duration
(ex. 1M = 1-minute spread)
Press the up or down button to cycle through
the following time scales:
CO2Timespan Time Per Unit
Auto - -
1M 1 minute 5 sec.
1H 1 hour 5 min.
1D 1 day 2 hours
1W 1 week 0.5 days

20
PROGRAMMING
STEP 1 - NIGHT 1 START
Press the up or down button to first set up a
START clock-time in NIGHT 1 START to turn
your device off.
STEP 2 - NIGHT 1 END
Press the mode button to navigate to NIGHT
1 END and set an END clock-time to turn your
device on. This option will only appear if you set
NIGHT 1 programming.
STEP 3
Repeat these steps in NIGHT 2 if you have a
device plugged into Outlet 2.
The countdown will begin if no buttons are
pressed for 5 seconds. The time left on the
countdown before the next ON or OFF phase is
displayed on the lower left corner.
NIGHT SETTING
Shuts off your device within a set timeframe, turning back on when the schedule ends. This will
override all programming set in Outlet 1 or Outlet 2, even while away from this setting. Make sure
the system clock time is correct before adjusting this setting. NIGHT 1 programs Outlet 1 while
NIGHT 2 programs Outlet 2.