Acteon x-mind ac Instruction Manual

INSTALLATION &
MAINTENANCE MANUAL
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B

2
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
MANUFACTURER
de Götzen®S.r.l. - a company of ACTEON Group
Via Roma, 45
21057 OLGIATE OLONA (VA) – ITALY
Tel. [phone]
Fax [phone]
www.degotzen.com - www.acteongroup.com
E-mail: [email protected]
For technical support:
[email protected]
www.acteongroup.com
ITALY
For information and technical assistance, contact the manufacturer
Direct Tel.: [phone]
[email protected]
WORLDWIDE
Contact your authorised local dealer.
Refer to the list in the following page to nd the authorised dealer near you.
THE RADIOGRAPHIC SYSTEM DESCRIBED IN THIS MANUAL REFERS TO A WALL INSTALLATION.

3
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
de Götzen® S.r.l. – ACTEON Group RESERVES ITSELF THE RIGHT TO MODIFY THE PRODUCTION
AND THE MANUAL WITHOUT NOTICE.
IT IS PROHIBITED TO MODIFY, COPY, REPRODUCE, DISPLAY, SHARE, DISCLOSE AND PUBLISH
THIS MANUAL AND ALL OTHER DOCUMENTS REFERRING TO “x-mind ac®” IN ANY FORM
WITHOUT PRIOR WRITTEN CONSENT BY de GÖTZEN® S.r.l. – ACTEON Group.
THE MANUAL MUST ALWAYS BE KEPT NEAR THE MEDICAL DEVICE FOR FUTURE REFERENCE.
de Götzen® S.r.l. – ACTEON Group SHALL NOT BE LIABLE FOR AN INCORRECT USE OF THE
INFORMATION CONTAINED IN THIS MANUAL.

4
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH

5
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
CONTENTS
CONTROL PANEL .....................................................................................................................6
CHAPTER 1................................................................................................................................7
1.1. PRELIMINARY INFORMATION .................................................................................................7
1.2. INFORMATION FOR THE OPERATOR ......................................................................................7
1.3. QUALITY DETERMINANTS IN X-RAY INTRAORAL RADIOGRAPHY .......................................8
1.4. WARRANTY CODITIONS ...........................................................................................................9
1.5. TRANSPORT CONDITIONS.......................................................................................................9
1.6. SAFETY WARNINGS...................................................................................................................9
CHAPTER 2..............................................................................................................................14
2.1. RADIOGRAPHIC SYSTEM........................................................................................................14
2.2. SYSTEM COMPONENTS..........................................................................................................15
2.3. IDENTIFICATION TAGS ...........................................................................................................16
CHAPTER 3..............................................................................................................................19
3.1. CONFIGURATION....................................................................................................................19
CHAPTER 4..............................................................................................................................21
4.1. INSTRUCTIONS FOR USE........................................................................................................21
CHAPTER 5..............................................................................................................................27
5.1. CHART OF DEFAULT EXPOSURE VALUES..............................................................................27
CHAPTER 6..............................................................................................................................32
6.1. PROGRAMMING DEFAULT EXPOSURE VALUES ...................................................................32
6.2. RESTORING ORIGINAL VALUES.............................................................................................34
CHAPTER 7..............................................................................................................................35
7.1. DIAGNOSTIC............................................................................................................................35
CHAPTER 8..............................................................................................................................36
8.1. ERROR MESSAGES...................................................................................................................36
CHAPTER 9..............................................................................................................................37
9.1. VERIFICATION OF THE EXPOSURE FACTORS .......................................................................37
CHAPTER 10............................................................................................................................39
10.1. SUGGESTED MAINTENANCE ...............................................................................................39
10.2. CLEANING THE OUTER SURFACES......................................................................................39
CHAPTER 11............................................................................................................................41
11.1. REPAIR....................................................................................................................................41
11.2. DISPOSAL...............................................................................................................................41
ANNEX 1 .................................................................................................................................42
A1. TECHNICAL SPECIFICATIONS .................................................................................................42
ANNEX 2 .................................................................................................................................46
A2. INTENDED ENVIRONMENT.....................................................................................................46
ANNEX 3 .................................................................................................................................47
A3. LIST OF INTERNATIONAL STANDARDS AND DIRECTIVES ...................................................47
ANNEX 4 .................................................................................................................................48
A4. DOSIMETRIC INDICATIONS....................................................................................................48
ANNEX 5 .................................................................................................................................49
A5. ELECTROMAGNETIC COMPATIBILITY....................................................................................49
ANNEX 6 .................................................................................................................................53
A6. DRAWINGS AND DIMENSIONS..............................................................................................53
ANNEX 7 .................................................................................................................................55
A7. INSTALLATION ELECTRICAL SCHEME....................................................................................55

6
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
CONTROL PANEL

7
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
CHAPTER 1
1.1. PRELIMINARY INFORMATION
Before beginning to use the “x-mind ac®” radiographic system, it is mandatory to carefully read and follow the
instructions contained herein, so as to obtain the best possible performance and to assure the safety of the
patient, operator, device and environment.
Always pay close attention to the
CAUTION
WARNING
PLEASE NOTE
messages when operating the system.
LEGEND
CAUTION
The word CAUTION identies those occurrences which might compromise the operator’s personal safety or cause injuries to people.
!
WARNING
The word WARNING identies those occurrences which might compromise the radiographic system’s performance.
PLEASE NOTE
PLEASE NOTE serve to give special indications so as to facilitate maintenance or make important information clearer.
1.2. INFORMATION FOR THE INSTALLER
CAUTION
The installer is responsible for the installation, with regards to the system safety and operation.
For safe and reliable installation of the “x-mind ac®” radiographic system it is advisable to:
- check that the voltage mentioned in the rating plate matches the line voltage;
- install the radiographic system according to the procedures described in this manual;
- provide the user with any information regarding the use of the radiographic system according to what stated
in the manual;
- certify the work done by a “Declaration of Conformity”;
- return to de Götzen® S.r.l. – ACTEON Group the warranty certicate duly lled in: if this is not done, the warranty
is not valid.
11

8
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
1.3. WARRANTY CONDITIONS
Inappropriate use or any arbitrary tampering with the equipment exempt de Götzen® S.r.l. – ACTEON Group,
as manufacturer of the “x-mind ac®” radiographic system, from any service under warranty or from any other
liability.
The warranty is valid only if the following precautions are taken:
- any repairs, modications, adjustments, recalibrations must be performed only by de Götzen® S.r.l. – ACTEON
Group;
- the installation must be made by professionally qualied technicians according to the regulations in force;
- the system must be installed and used in compliance with the instructions given in this manual and for the
purposes and applications for which it was designed;
- the power supply must be adequate to supply the required power indicated in the radiographic system’s
nameplate data;
- in order to safeguard one’s warranty rights, please ll in the enclosed Warranty Document, immediately after
the installation is completed, together with the technician;
- the system must be checked completely at least each 12 months by professionally qualied technicians according
to the regulation in force; use the manuals provided with the device “x-mind ac®” for reference;
- in case of repair, please use only spare parts from the manufacturer of the “x-mind ac®”; otherwise basic safety
and essential performances of the device will not be guaranteed.
de Götzen® S.r.l. – ACTEON Group is not responsible for any damages caused by any person or thing as a
consequence of non-compliance of any or all guidelines contained in all the manuals provided with the
“x-mind ac®” device.
CAUTION
Non compliance of any of the above mentioned rules and all the indications provided by the manufacturer in the documentation, or successively
in written paper or electronic format, will result in losing the warranty of the product and the manufacturer will be discharged from any obliga-
tion, including consequential damages, direct or indirect that may derive to people, things or environment. Furthermore, the facility represen-
tative, customer or employees of the facility, will be liable for any damage and/or incident and/or degeneration of the health status of a patient,
operator, involved people and the surrounding environment.
1.4. TRANSPORT CONDITIONS
The “x-mind ac®” radiographic system travels at the receiver’s own risk.
All claims for damage or miscarriage regarding the shipment must be pointed out in the presence of the shipping
agent.
In case of miscarriages, or actual or suspected damage, the receiver shall indicate the proper reserves on the
transport documentation or on the consignment note.

9
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
1.5. SAFETY WARNINGS
A few safety recommendations which should be followed when using the “x-mind ac®” radiographic system are
listed here below.
CAUTION
GENERAL REQUIREMENTS
RESPONSIBLE ORGANIZATION is the authority that has the responsibility for the USE and MAINTENANCE of the “x-mind ac®” radiographic sys-
tem. The training and preparation of personnel is the responsibility of THE RESPONSIBLE ORGANIZATION.
“x-mind ac®” radiographic system is an Xray generator and must be used and handled only by specialised surgeons, dentists and authorized
personnel, who meet the requirements provided by the national laws in force in the country of installation.
It is mandatory for the RESPONSIBLE ORGANIZATION to provide a routine and special maintenance schedule for medical equipment; this sche-
dule must be documented for every device and transmitted to the various operating levels (*). The preventive maintenance (that must be perfor-
med at least every 12 months), which includes functional, performance and safety tests of the device, must be carried out by qualied, authorized
professional technicians. It is mandatory to ensure patients’ health and safety and proper “x-mind ac®” radiographic system operation (IEC
60601-1 etc.). These operations must be carried out according to the methods and frequency indicated in this manual and in the installation and
maintenance manual. Failure to comply with this requirement or with the messages concerning anomalies will release the manufacturer from
any liability for direct and indirect injuries to persons and/or damage to property or the environment. Furthermore, the managers of the facility,
customers or collaborators shall be held liable for any damage and/or accidents and/or degeneration of patients’ or operators’ health or of the
surrounding environment.
The RESPONSIBLE ORGANIZATION must also provide for the safe and proper use of the equipment.
(*) For Italy refer to Presidential Decree 14/01/1997, Legislative Decree No. 81/2008 (as subsequently amended and modied).
Operators must know the environmental and operating specications of the device, as well as the procedures to follow in the event of hazards or
emergency stops.
“x-mind ac®” radiographic system has been designed to acquire radiographic images for dental intraoral X-ray imaging. The “x-mind ac®”
medical device must not be used for X-ray imaging of other body parts.
Carefully follow the instructions in this manual to install, operate and maintain the “x-mind ac®” radiographic system. In the event that local
laws and standards are more restrictive than the manufacturer’s indications, the former supersede the latter.
The RESPONSIBLE ORGANIZATION must comply with the standards and regulations in force concerning the installation of the medical device in
consideration of the place of installation.
The operator is responsible to monitor the patient and the parameters of the “x-mind ac®” radiographic system throughout the entire duration
of the X-ray examination.
It is prohibited to modify any part of the “x-mind ac®” medical device.
de Götzen S.r.l. – ACTEON Group and its authorized technicians are not required to verify compliance of the installation site with local standards
concerning electrical safety and X-ray protection and with any other directive concerning safety in force in the Country of installation.
The RESPONSIBLE ORGANIZATIONS of the facility must ensure compliance of the installation site with the local laws in force.
Before each examination, it is mandatory to apply to the collimator cone (Beam Limiting Device) a disposable protection sheath designed to
cover the end part of the X-ray unit, which is more susceptible of being directly contaminated during the X-ray exposure (class I Medical Device
Directive 93/42/EEC and subsequent amendments). It can come in contact with the patient’s skin: verify biocompatibility according to the prin-
ciples given in the ISO 10993 series of standards, refer for details to the disposable use protection’s instructions for use.
Before operating the “x-mind ac®” radiographic system you must assure that the device has no visible signs of damage.

10
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
CAUTION
PROTECTION AGAINST RADIATIONS
“The general principles regarding safety and protection of workers and people” must always be applied when using the unit:
1. Justication of the practice
2. Protection Optimisation
3. Reduction of the limits of individual dose and risks
The “x-mind ac®” is a medical device that generates X-rays; therefore, both the patients and the operator are exposed to risks due to ionizing
radiation. The physician must assess the actual need for X-ray exposure.
All personnel present during an X-ray examination must comply with safety regulations concerning protection against radiation. For their own
safety, the operator must always keep a distance of more than 2 meters (6 ft.) and out of the path of the X-ray beam, in order to avoid the exposi-
tion to the stray radiation and residual radiation.
The “x-mind ac®” medical device must be used in compliance with the local standards in force and with the international directives concerning
radiation protection.
The device must comply with the guidelines and indications provided by an accredited specialist in radiation protection, who will recommend, if
necessary, the additional shields or precautions for every specic case.
The device installation site must be shielded in compliance with the local standards in force to protect the operator, patient and other people
against X-rays.
The “x-mind ac®” device is intended to be used solely by surgeons, dentists and qualied and authorized physicians. The operator must:
- determine, when appropriate, the possible need for sedation and the related operating methods and precautions best suited appropriate for
the patient
- supervise the entire X-ray examination procedure, paying attention to the indications and information from the unit.
The device must be used only for diagnostic purposes by qualied and authorized dentists and/or physicians.
The operator and other personnel must keep clear from the patient during the scan.
The personnel involved in the radiographic examination must take all the safety measures concerning radiation protection.
It is the operator’s responsibility to protect the patient against unnecessary or excessive radiation doses.
Additional protection devices (aprons, collars, etc) are required to protect the patient from radiation.
Before exposing patients with pacemakers, contact the manufacturer of the latter to ensure that the X-rays generated by “x-mind ac®” do not
interfere with its functionality.
“x-mind ac®” generates X-rays: before using this X-ray system please refer to the regulation in force in your area concerning paediatric patients,
pregnant women and anyone with health issues that contraindicate the use of X-rays. Investigate and make sure of this condition before starting
the exposure.
This symbol indicates X-ray hazard.

11
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
CAUTION
MECHANICAL RISK
Before removing the tubehead from the positioning arm, RELEASE THE SPRING.
The sudden opening of the joint may cause damage to people and/or things.
Check that the installation of the unit complies with the mechanical specications of the support (walls, ceiling, etc..) where it is installed.
Adjustments or any kind of attempt of repairing or disassembling must only be performed by qualied and authorized service personnel.
The “x-mind ac®” must not be used in environments or close to environments subjected to mechanical vibrations or mechanical shocks.
CAUTION
ELECTRIC SAFETY
The radiographic system contains high voltage. It’s prohibited to inspect internal parts of the system.
Never attempt to open the X-ray tubehead.
The covers on the “x-mind ac®” radiographic system must only be removed by qualied and authorized service personnel.
The unit must be used only in environments that are in compliance with all electrical safety standards set forth for medical environments.
To avoid the risk of electric shock, this device must only be connected to a supply mains with protective earth.
The unit is NOT equipped with protections against penetration of liquids; it will therefore be necessary to make sure that no water or other
liquids penetrate inside in order to avoid short circuits or corrosion.
Always disconnect the radiographic system from the power supply and wait for 2 minutes before beginning to clean, disinfect and maintenance
operations.
Do not connect the X-ray system to a multiple portable socket outlet (MPSO) nor to any type of extension cord.
External equipment intended for connection to signal input, signal output or other connectors shall comply with the relevant product standard
e.g. IEC 60950-1 for IT equipment and the IEC 60601-series for medical electrical equipment. In addition, all such combinations – systems – shall
comply with the safety requirements stated in the general standard CEI EN 60601-1, edition 3, clause 16. Any equipment not complying with the
leakage current requirements in CEI EN 60601-1 shall be kept outside the patient environment i.e. at least 1,5 m from the patient support.
It is mandatory to use an isolation device (Separation Device) to isolate the equipment located outside the patient environment from the equip-
ment located inside the patient environment. In particular, such a Separation Device is required when a network or data connection is made. The
requirements on the Separation Device is dened in CEI EN 60601-1, edition 3, clause 16.
For the wall version of “x-mind ac®”:
based on the CEI EN 60601-1, the installation is a permanent type (xed). IT IS NOT ALLOWED TO connect the equipment to the main supply using
a plug.
The cone (beam limiting device) is an APPLIED PART of the system and it is classied as type B.

12
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
CAUTION
EMC COMPATIBILITY
EMC requirements must be considered and the “x-mind ac®” must be installed and used accordingly with the specic EMC information provided
in the accompanying documents.
The device complies with the EMC (Electromagnetic Compatibility) requirements, according to CEI EN 60601-1-2. Radio transmitting equipment,
cellular phones etc. shall not be used in close proximity of the unit as they could inuence the performance of the system.
Carefully read the indications relevant to the EMC in the dedicated appendix A5. EMC compatibility of this manual.
CAUTION
PROTECTION AGAINST EXPLOSIONS
The radiographic system MUST NOT be used in the presence of disinfectant, ammable or potentially explosive gases or vapours that might
catch re and cause damage.
In case these disinfectants have to be used, let the vapour completely disperse before turning on the radiographic system.
CAUTION
SYSTEM MODIFICATIONS OR UPGRADES
Modications or upgrades of the system can be carried out only if advised by de Götzen® S.r.l. – ACTEON Group and performed by authorized
and qualied personnel, using ONLY genuine original spare parts of de Götzen® S.r.l. – ACTEON Group.
de Götzen® S.r.l. – ACTEON Group proscribes improper, unauthorized modications or upgrades of the device, in order to avoid malfunctions
resulting in breakdowns and/or accident for patient, operator and equipment. de Götzen® S.r.l. – ACTEON Group assumes no responsibility and,
consequently, declines all responsibility with respect to direct or indirect damages to people, the device or environment due to these reasons.
Do not remove or attempt to remove the plastic covers of the device.
It is strictly forbidden to attempt to repair electronic or mechanical parts by yourself.
Disregarding this warning can result in irreversibly compromising the overall safety of the system and can be dangerous for operators, patients
and environment.

13
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
CHAPTER 2
2.1. RADIOGRAPHIC SYSTEM
The “x-mind ac®” radiographic system guarantees the maximum safety both for the operator and the patient.
It is built in compliance with the following European Directives:
} 93/42/EEC and subsequent amendments MEDICAL DEVICES
} EURATOM 96/29 IONISING RADIATIONS
and in compliance with the following American Standard:
} American Radiation Performance Standard 21CFR, Subchapter J, Sec. 1020.30 and 1020.31
The following protective measures were adopted in the design and construction of the unit:
- protection against the risk of electric injuries, ensured by a grounded protection conductor;
- protection against leakage radiation, made negligible by the shielded casing;
- protection against excessive radiations, thanks to the immediate activation of the safety device;
- protection against continuous service, since the system is designed, according to standards, not to allow the
use in radioscopy;
- protection for the patient against dangerous radiations, obtained by means of the high frequency technology
capable of producing a constant and hard radiation
- protection against exposure mistakes obtained with the self-compensating technology which, by revealing
voltage uctuation, is able to modulate the irradiation time ensuring the proper level of dose;
- protection for the operator against irradiation ensured by the extensible cable of the hand control which
allows for a safety distance of more than 2 meters (6 ft.);
- protection against involuntarily selection of radiographic technique (FILM or DIGIT) obtained, according to
standards, by means of the conrming on the selection key.
“ELECTRO-MEDICAL” CLASSIFICATION
According to paragraph §6 of the general safety regulations CEI EN 60601-1: 2007 on
safety of medical equipment, the system is classied as: Class I - Type B
“MEDICAL DEVICES” CLASSIFICATION
According to the classication rules indicated in attachment IX of the EEC Directive 93/42 on medical devices
and subsequent amendments the system is classied as: Class IIb
“E.M.C.” CLASSIFICATION
According to paragraph §4 of the CEI EN 55011, the system is classied as: Group 1 – Class B
22

14
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
2.2. SYSTEM COMPONENTS
x-mind ac®” radiographic system (Fig. 1) consists of:
1. x-mind ac® TIMER
The timer is the control panel used to manage the exposure times and to safely use the tubehead.
To make the exposure, the control button with safety key is available.
The timer can be connected to n° 2 ac tubeheads.
In case of alternate current tubeheads the technology of the timer is “self - compensating”:
depending on the line voltage uctuation, the microprocessor automatically modies the predetermined expo-
sure time ensuring a constant dose to the patient.
This technological expedient avoids the repetition of the exposure because of over/under exposure errors.
2. WALL PLATE
3. BRACKET
The horizontal bracket is available in 3 different lengths (110 cm, 80 cm, 40 cm) and represents the support for
the pantograph arm. Its shaft is xed in a dedicated section of the timer (top or bottom) and allows for 180°
movement.
4. PANTOGRAPH ARM
Thanks to the new shape and new mechanisms of the positioning arm, it can be adjusted in height and depth
in order to precisely explore any spot in its reach.
It is made of light alloy with an ABS coating.
5. TUBEHEAD x-mind ac®
The intra-oral tubehead “x-mind ac®” is a monoblock type and its light alloy housing contains an airtight com-
partment.
The high voltage transformer, the X-ray tube and the expansion chamber are submerged in highly dielectric
insulating oil inside a light alloy container.
The expansion chamber guarantees an adequate compensation to oil expansion for the entire temperature
range.
The X-ray tube is located in the back part of the container, allowing a source-skin distance 50% higher than
traditional structures.
6. CONE
The collimator cone or Beam Limiting Device represents the applied part of the device. Made of the transparent
polycarbonate, it allows:

15
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
- the correct distance between focal spot and skin
- dimension, direction and centering of X-ray beam
- the realization of different radiographic technique (bisecting and parallel technique).
During X-ray exposition, the collimator cone comes in contact with the skin of the patient.
Before each exam, it is necessary to apply to the cone a disposable protective cover designed to cover the end
part of the X-ray generator.
Such protection has two functions: avoid crosscontamination (from patient to patient) and prevent the possibi-
lity of inammations or other types of reactions of the skin caused by contact with the material that constitutes
the cone.
OPTIONAL ACCESSORIES
}SECOND CONTROL BUTTON
}x-mind ac® LIGHT (X-ray signalling lamp for external use)
}x-mind ac® ECB (remote control button)
PLEASE NOTE
For the installation of the optional accessories, refer to the specic installation manuals supplied.
2.3. OVERALL DIMENSIONS
Fig. 2A, 2B, 2C give the overall dimensions of the possible supply conditions:
BRACKET 400: L = 41 cm – 16” 9/64
BRACKET 800: L = 82,5 cm – 32” 31/64
BRACKET 1100: L = 110 cm – 43” 5/16
BRACKET 400

16
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
BRACKET 800
BRACKET 1100

17
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
Fig. 3 and 4 show the typical dimensions of the radiographic system:

18
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
2.4. IDENTIFICATION TAGS
The identication tags on the tubehead, on the timer and on the cone indicate the model number, the serial
number, the manufacturing date and the symbols of the main technical characteristics.
2.3.1. TUBEHEAD
Model 230 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) - ITALY
70kVp 8mA
230V ~ 50/60Hz
TOSHIBA DG-073B-AC
Rated line voltage:
X-ray tub e :
Total filtratio n: 2,3mm Al / 70kV 0.7mm
Class I
tube:
SN SN
Model 220 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) - ITALY
70kVp 8mA
220V ~ 50/60Hz
TOSHIBA DG-073B-AC
Rated line voltage:
X-ray t ub e:
Total filtration: 2,3mm Al / 70kV 0.7mm
Class I
tube:
SN SN
Model 115 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) - ITALY
70kVp 8mA
115V ~ 50/60Hz
TOSHIBA DG-073B-AC
Rated line voltage:
X-ray t ub e:
Total filtration: 2,3mm Al / 70kV 0.7mm
Class I
tube:
SN SN
2.3.2. TIMER
Model 230 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) – ITALY
Rated line voltage:
Absorbed power:
230V 50/60Hz Class I
0,8kVA IP20
~
SN

19
ENGLISH
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
Model 220 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) – ITALY
Rated line voltage:
Absorbed power:
220V 50/60Hz Class I
0,79kVA IP20
~
SN
Model 115 V
Model: x-mind ac
®
de Götzen S.r.l.
®
Via Roma 45 - 21057 Olgiate Olona (VA) – ITALY
Rated line voltage:
Absorbed power:
115V 50/60Hz Class I
0,66kVA IP20
~
SN
CONE
GRADUATED SCALE

20
INSTALLATION & MAINTENANCE MANUAL • X-MIND AC • V2 • (06) • 08/2016 • NXACEN020B
ENGLISH
PICTOGRAMS USED
SYMBOL INDICATING THE MANUFACTURER
THIS SYMBOL GUARANTEES THAT THE RADIOGRAPHIC SYSTEM COMPLIES WITH THE
REGULATIONS CONTAINED IN THE EUROPEAN DIRECTIVE EEC 93/42 REGARDING MEDICAL
DEVICES
SIZE OF THE FOCAL SPOT
THE DEGREE OF PROTECTION AGAINST DIRECT AND INDIRECT ELECTRIC CONTACTS IS B
TYPE
SYMBOL INDICATING THE SERIAL NUMBER
SYMBOL INDICATING DANGER DUE TO IONISING RADIATIONS
X-ray EMISSION (IEC 60417)
PAUSE (IEC 60417)
ATTENTION, REFER TO THE ATTACHED DOCUMENTS
REFER TO MANUAL’S INSTRUCTIONS
WEEE (Waste Electrical and Electronic Equipment) SYMBOL, IN CONFORMITY WITH 2012/19/
CE DIRECTIVE AND EN 50419 STANDARD.