ActionTec GT701D User manual

DSL Modem
Model #: GT701D
User Manual
Ver 1.0
Solutions for the Digital Life™

Table of Contents
1 Introduction 1
Minimum System Requirements 1
Features 2
Getting to Know the Modem 3
2 Performing a Quick Setup 7
Accessing Quick Setup Screens 7
Changing the Password 9
3 Viewing the Modem’s Status 11
Broadband Connection Status 11
Network Status 14
4 Configuring Advanced Setup Options 15
Accessing the Advanced Setup Options 15
DSL Settings 17
DHCP Settings 18
LAN IP Address 20
WAN IP Address 21
QoS Settings Upstream 23
QoS Settings Downstream 25
QoS Status 26
Remote Management 26
Telnet Timeout Setting 27
Dynamic Routing 28
Static Routing 28
UPnP (Universal Plug and Play) 29
Time Zone 29
Remote Syslog Capture 30
5 Configuring Security Settings 31
Accessing Wired Security Screens 31
Admin User Name and Password 32
Firewall 33
Port Forwarding 37
DMZ Hosting 39
NAT (Network Address Translation) 40
i

ii
Actiontec DSL Modem User Manual
ii
6 Configuring Internet Access Controls 41
Accessing Internet Access Control Screens 41
Services Blocking 42
Website Blocking 43
Schedule Rules 44
7 Configuring the Modem’s Utilities 47
Accessing the Utilities Screens 47
Restore Default Settings 49
Upgrade Firmware 49
Web Activity Log 50
System Log 51
OAM Ping Test 52
Ping Test 52
Reboot 53
8 Troubleshooting 55
Troubleshooting 55
Frequently Asked Questions 57
A Specifications 61
General 61
LED Indicators 62
Environmental 62
B Setting up Static IPon a Computer 63
Windows 2000 63
Windows XP 68
Windows Vista 71
C Service Acronyms 75
Service Acronym Definitions 75
D Glossary 79
Notices 83
Regulatory Compliance Notices 83
Modifications 83
Limited Warranty 85

1
Introduction
Thank you for purchasing the Actiontec DSL Modem. The Modem is the simplest
way to connect computers to a high-speed broadband connection. This easy-to-use
product is perfect for the home office or small business. If you want to take your
computing to the next level, the DSL Modem is sure to be one of the keys to
your success.
Minimum System Requirements
tActive DSL service
tComputer with a 10 Mbps or 10/100 Mbps Ethernet connection
tMicrosoft Windows 2000, XP, Vista
Mac OS 7.1+, 8.0+, 9.0+, OS X+
tInternet Explorer 4.0 or higher (5.x+ recommended) or Netscape Navigator
4.0 or higher (4.7+ recommended)
tTCP/IP network protocol installed on each computer
1

2
Actiontec DSL Modem User Manual
Features
tADSL WAN port (RJ-11)
tFull-rate ANSI T1.413 Issue 2, ITU G.992.1(G.dmt) and G.992.2(G.lite)
standard compliance
tAuto-handshake for different ADSL services
tBridged Ethernet over ATM, PPP over ATM, PPP over Ethernet
tPrecise ATM traffic shaping
tIP packet routing and transparent bridge
tRIP-1, RIP-2, and static routing protocol support
tBuilt-in NAT, DHCP server
tDNS relay support
tPAP/CHAP authentication, administrative passwords through Telnet
tIEEE 802.3 Ethernet standard compliance
t10/100 Base-T Ethernet ports (4)
tFast Ethernet flow control support
tWeb-based configuration setup
tFTP firmware upgradeable
tWeb download support

3
Chapter 1 Introduction
Getting to Know the Modem
This section contains a quick description of the Modem’s lights, ports, etc.
The Modem has several indicator lights (LEDs) on its front panel and a series of
ports on its rear panel.
Front Panel
The front panel of the Modem features four lights: Power, DSL, Internet, and
Ethernet.
Power Light
The Power light displays the Modem’s current status. If the Power light glows
steadily green, the Modem is receiving power and fully operational. When the
Power light is rapidly flashing, the Modem is initializing. If the Power light glows
red when the Power cord is plugged in, the Modem has suffered a critical error
and technical support should be contacted.
DSL Light
The DSL light illuminates when the Modem is connected to a DSL line and the
unit is able to synchronize to the DSL signal from the ISP. When it flashes, the
Modem’s built-in DSL modem is training for the DSL service.

4
Actiontec DSL Modem User Manual
Internet Light
When the Internet light glows steadily, the Modem is connected to the
DSL provider.
Ethernet Light
The Ethernet light illuminates when the Modem is connected to a computer via
its yellow Ethernet port.
Rear Panel
The rear panel of the Modem features three ports (DSL, Ethernet, and Power), as
well as a Reset switch.
Ethernet Port
The Ethernet port is used to connect a computer to the Modem via Ethernet
cable. The Ethernet port is a 10/100 Mbps auto-sensing port, and either a
straight-through or crossover Ethernet cable can be used when connecting to
the port.
DSL Port
The DSL port is used to connect the Modem to a DSL (Digital Subcriber Line)
connection.

5
Chapter 1 Introduction
Reset Switch
Depressing the Reset switch restores the Modem’s factory default settings. To
reset the Modem, depress and hold the Reset switch for five to seven seconds.
The reset process will start after releasing the switch, during which the Power
light will turn from green to orange.
USB Port
The USB port is used to connect a computer to the Modem via USB cable.
Power Port
The Power port is used to connect the Power cord to the Modem.
MWarning:Do not unplug the Power cord from the Modem dur-
ing the reset process. Doing so may result in permanent damage
to the Modem.
Power Switch
The Power switch is used to power the Modem on and off.

6
Actiontec DSL Modem User Manual
This page left intentionally blank.

7
Performing a
Quick Setup
This chapter is a guide through a quick set up of the Modem, including how to
connect the Modem to the ISP.
To complete the quick setup, have the Welcome Letter or ISP Worksheet handy. If
the document is not available, contact the ISP immediately.
Accessing Quick Setup Screens
To access the Quick Setup screens:
1. Open a Web browser. In the “Address” text box, type:
http://192.168.0.1
then press Enter on the keyboard.
2