Acu-rite 00381 User manual

Instruction Manual

Thermometer

model 00381

CONTENTS

Unpacking Instructions ........... 2

Package Contents .................. 2

Features & Benets................. 2

Setup .................................... 3

Install or Replace Batteries...... 3

Temperature Units .................. 4

Placement Guidelines ............. 4

Troubleshooting ..................... 5

Care & Maintenance.............. 6

Specications......................... 6

FCC Information .................... 6

Customer Support .................. 7

Warranty............................... 7

Questions? Contact Customer Support at

(877) 221-1252 or visit www.AcuRite.com

SAVE THIS MANUAL FOR FUTURE REFERENCE.

1111

Congratulations on your new AcuRite product. To ensure the best

possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this

product. Locate the tab and peel off to remove.

Package Contents

1. Display

2. Outdoor Sensor

3. Instruction Manual

PRODUCT MUST BE REGISTERED

IMPORTANT TO RECEIVE WARRANTY SERVICE

PRODUCT REGISTRATION

www.AcuRite.com

Features & Benets

OUTDOOR SENSOR

2 1. Integrated Hanger

For easy placement.

2. Wireless Signal Indicator

Flashes when data is being sent to

the display.

3. Battery Compartment Cover

LITHIUM 4 -

BATTERIEScp•e1•·u

ALKALINE

BATTERIES (70°C) 158°F I

Features & Benets

LOW

7 DISPLAY FRONT

1. Outdoor Sensor Signal Strength

2. Indoor or Outdoor Temperature

6 3 . Low Temperature Record

Lowest temperature recorded over

the past 24 hours.

4. High Temperature Record

Highest temperature recorded

over the past 24 hours.

5. Display Low Battery Indicator

5 6. Indoor or Outdoor Temperature

Indicator

4 Indicates which temperature is

currently being viewed.

7. Indoor or Outdoor Button

Press to toggle between indoor

and outdoor temperature.

SETUP

Install or Replace Batteries

AcuRite recommends high quality alkaline batteries for the best product

performance. Heavy duty or rechargeable batteries are not recommended.

The outdoor sensor requires lithium batteries in low temperature conditions.

Cold temperatures can cause alkaline batteries to function improperly. Use

lithium batteries in the outdoor sensor for temperatures below -4ºF / -20ºC.

Outdoor Sensor

1. Slide off the battery

compartment cover.

2. Insert 2 x AA batteries into

the battery compartment, as

shown. Follow the polarity

(+/-) diagram in the battery

compartment.

3. Replace the battery cover.

SETUP

Display

1. Slide off the battery compartment cover.

2. Insert 2 x AAA batteries into the battery

compartment, as shown. Follow the

polarity (+/-) diagram in the battery

compartment.

3. Replace the battery cover.

Select Degrees Fahrenheit or Celsius

To select between degrees Fahrenheit (ºF) or Celsius (ºC) temperature units,

press the “ºC/ºF” button located inside the battery compartment of the display.

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE

WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be

used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used

batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in ﬁre,

as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge

non-rechargeable batteries. DO NOT short-circuit the supply terminals.

Placement for Maximum Accuracy

AcuRite sensors are sensitive to surrounding environmental conditions. Proper

placement of both the display and outdoor sensor are critical to the accuracy

and performance of this product.

Display Placement

Place the display in a dry area free of dirt and dust. Display stands

upright for tabletop use or is wall-mountable.

Outdoor Sensor Placement

Sensor must be placed outside to observe outdoor conditions.

Sensor is water resistant and is designed for general outdoor use,

however, to extend its life place the sensor in an area protected

from direct weather elements.

Hang the sensor using the integrated hang holes or hanger, or by

using string (not included) to hang it from a suitable location, like a

well covered tree branch. The best location is 4 to 8 feet above the

ground with permanent shade and plenty of fresh air to circulate

around the sensor.

T111I

Important Placement Guidelines

• To ensure accurate temperature measurement, place units out of direct

sunlight and away from heat sources or vents.

•Display and outdoor sensor must be within 165 ft (50 m) of each other.

• To maximize wireless range, place units away from large metallic items, thick

walls, metal surfaces, or other objects that may limit wireless communication.

• To prevent wireless interference, place both units at least 3 ft (.9 m) away

from electronic devices (TV, computer, microwave, radio, etc.)

(165 feet maximum)

(50 meters)

Setup is Complete

The sensor will now synchronize with the display. It may take a few minutes for

synchronization to complete. Please refer to the troubleshooting section of this

manual if anything appears to be functioning improperly.

Troubleshooting

Problem Possible Solution

No outdoor sensor

reception

no bars

If the wireless signal indicator shows no bars:

• Relocate the display and/or the outdoor sensor. The

units must be within 165 ft (50 m) of each other.

• Make sure both units are placed at least 3 feet (.9 m)

away from electronics that may interfere with the

wireless communication (such as TVs, microwaves,

computers, etc).

• Use standard alkaline batteries (or lithium batteries

in sensor when temperature is below -4ºF/-20ºC). Do

not use heavy duty or rechargeable batteries. NOTE:

It may take a few minutes for display and sensor to

synchronize after batteries are replaced.

Outdoor

temperature

is ashing or

showing dashes

Flashing of the outdoor temperature is generally an

indication of wireless interference.

1. Bring both the sensor and display indoors and

remove at least one battery from each.

2. Reinstall the battery in the outdoor sensor.

3. Reinstall the battery in the display.

4. Let the units sit within a couple feet of each other for

a few minutes to gain a strong connection.

Problem Possible Solution

Inaccurate

temperature

• Make sure both the display and sensor are placed out

of direct sunlight and away from any heat sources or

vents (see page 4).

Display screen

not working

• Check that the batteries are installed correctly.

Batteries may need to be replaced.

If your AcuRite product does not operate properly after trying

the troubleshooting steps, visit www.AcuRite.com or call

(877) 221-1252 for assistance.

Care & Maintenance

Display Care

Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away

from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air.

Outdoor Sensor Care

Clean with a soft damp cloth. Do not use caustic cleaners or abrasives.

Specications

TEMPERATURE RANGE Outdoor: -40ºF to 158ºF; -40ºC to 70ºC

Indoor: 32ºF to 122ºF; 0ºC to 50ºC

WIRELESS RANGE 165 ft / 50 m depending on home construction materials

WIRELESS FREQUENCY 433 MHz

POWER Display: 2 x AAA alkaline batteries

Sensor: 2 x AA alkaline or lithium batteries

DATA REPORTING 30 second updates

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

1- This device may NOT cause harmful interference, and

2- This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.•

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.

Such modications could void the user authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

This device may not cause interference, and(1) This device must accept any interference received, including interference that may cause undesired operation of the device.(2)

Customer Support

AcuRite customer support is committed to providing you with best-in-class