Kohler K-98850T User manual

-1-
UPLIFT
INSTALLATION INSTRUCTIONS
MIRRORED CABINET
K-98850T
IMPORTANT INFORMATION
Grounding Instructions
WARNING: Risk of electric shock.
!
!
!
This product should be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current.
Improper use of
the grounding plug can result in a risk of electric shock.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely understood,
or if in doubt as to whether the product is properly
grounded.
The product complies with GB/T10357.4-2013,
GB/T10357.5-2013, GB24977-2010, GB8898-2011,
GB13837-2012, GB/T 9374-2012.
!
!
!
3mm
GB/T10357.4-2013 GB/T10357.5-2013
GB24977-2010 GB8898-2011 GB13837-2012 GB/T
9374-2012
Unit Specification
Rated voltage 100 240V 50/60Hz
Rated power <50W
Boundary dimension 900 X 650mm
Ambient temperature 0-40 C
o
Using height above sea level Below 5000 metres
Temperature Display Temperature display range 555
Clock Display Display format 24-hour format
Horn Rated power 6W
Resistance 8
Anti-fog Rated voltage DC12V
Rated power
Port type
<19W
AUX IN 3.5mm
Audio Interface
Lamps and Lanterns
Radio
Rated power
Color temperature of lamps and lanterns
Frequency Modulation
<6W
3000K
Comply With GB/T 9374-2012
TECHNICAL SPECIFICATION
©
©
Copyright Kohler China Investment Co., Ltd. 2016
2016
ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINYE ROAD, ZHONGSHAN TORCH
DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437
13-1 528437
1242001-T01-B

-2-
TOOLS AND MATERIALS
Drill with Assorted Bits Assorted
Screwdrivers
Band Tape PencilLevelling Ruler
Plus:
!
!
Protective Material
Tape
!
!
Outside Mirror Assy
X1
Cabanity Assy
X1
Balance Weight Block
X2
Side-Mirror Kits
X2
Wall Bracket
X1
Inside Mirror
X2
Glass Shelves
X4
1144255
Accessoris List
Screw ST3.5X35
X8
Hole Plugs
X18
Snap-in Pins
X18
Wedge
X4
Screw M4X12
X6
Wall Anchors
X8
Caps of Screw
X4
Kohler.comConsult the online users guide at kohler.com for more
information.
Kohler Co. reserves the right to make revisions in the
design of products without notice.
100 240V 50/60Hz
<50W
900 X 650mm
0-40 C
o
5000
555
24
6W
8
DC12V
<19W
AUX IN 3.5mm
FM
<6W
3000K
GB/T 9374-2012
1242001-T01-B

720
300
1100(Max)
1100( )
167 40
84
200
590
Floor
Faucet
Drill Holes (Wall Bracket)
3- 6( )
Uplift Cabinet
Drill Holes (Top Clips)
3- 6( )
Outlet
Ceiling
-3-
ROUGHING-IN
UNIT : mm
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value
INSTALLATION
900
1080(Max)
300
148
167
630
Step 1:
Note:
Drill installation holes at desired position. Make sure there is
enough space between the cabinet and the faucet or its
handle.
In order to make wave induction function to work
properly, the distance at least is 200mm between infrared
sensors and the faucet, or avoid facing below metal faucet.
30mm 200mm
200mm
1242001-T01-B

-4-
Step 2:
Install the wall bracket.
Step 3:
1. Put the cabinet onto wall bracket.
2. Slide top clips to align with the drilled holes and fix with
screws.
1.
2.
Step 4:
Install side mirror.
Screw M4X12
Screw Caps
Top Clip
Cabinet
Wall Bracket
1242001-T01-B

-5-
Step 5:
Install outer mirror assembly
1. Connect the data line and pay attention to its direction.
2. Fix the outer mirror onto mirror frame. Make sure the wall
bracket is installed correctly.
Note: Outer mirror is already assembled in factory. It can be
removed and re-assembled according to these steps if
necessary.
Step 6:
Install blocks
1. Lift the door to reveal block slot.
2. Put the two blocks (black iron blocks) into the slot.
3. Place the blocks level to ensure that they slide smoothly.
1.
2.
1.
2. 2
3.
Door
Block Slot
Block
1242001-T01-B

-6-
Step 7:
Install back mirror
1. Hold the handle. Incline the back mirror upwards and first
insert it into one end of the slot with the speaker cover, and
then insert into the other end. Adjust the mirror leftwards
and rightwards.
2. Insert the seal into the gaps at two sides of the back mirror
to make it stable.
3. After installation, remove the handle and protective film on
the mirror.
Step 8:
Install glass shelf.
1.
2.
3.
Back Mirror
Handle Seal
1
2
3
Aluminium Plate
Speaker Cover
Door
Back Mirror Slot
1242001-T01-B

-7-
Step 9:
Connect power line.
220V/50Hz
1242001-T01-B