Courtyard Creations TCS41CK-WM User manual

TCS41CK-WM
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the table top (#1) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Fasten the legs (#2) to the underside of the table
top (#1) rim by using bolts (#5) and washers (#7).
Keep the bolts loose. See Figure 1.
PARTS LIST
1
1
6
4
4
8
12
4
1
TCS41CK-CS01
TCS42CK-CS02
62TCS42CKY101
13C??1B29008001
17C01A0706001Y4
17C33A0709001Y4
17FA05040301-Y4
18000337004
17KAA0101----Y4
TABLE TOP
LEG
CENTER
CONNECTOR
TILE
BOLT M6*16
HEX.KEY WRENCH 4MM
BOLT CAP
WASHER d6.5*D13*1.0
BOLT M6*25
FIGURE 1
PART
NO. MATERIAL CODE PART Q’TY PART
NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
8
9
10
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
Note:
The tiles can break easily. Therefore, be careful
when removing them. Do not throw away the residual
tiles. Keep them for future use.
Do not sit or stand on this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
5
7
8
2
2
2
2
1
PAGE 1 OF 2 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
BOLT CAP M6
8
18000337001
#5 BOLT M6*25
25

#6 BOLT M6*16
77
6
6
9
9
PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOUHAVE
ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE PACKING
MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME SEPARATED
DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT 1-877-539-7436
BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
FIGURE 2 FIGURE 3
FIGURE 4
Step 3:
Turn the table to its upright position. Carefully
place the tiles (#4) onto the table top.
See Figure 3 and Figure 4.
Note:
If any EVA foams on the table top (#1) are
missing, there are extra EVA foams in the
hardware kit. See Illustration A.
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse
thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
•Inspect and tighten all bolts and fasteners on a
regular basis to ensure the proper performance
and safety of your table.
•When moving the table, lift. Do not drag this table.
•We recommend the use of furniture covers when
not in use.
•In order to prolong the life and beauty of your table,
we recommend that it be stored in a dry and
protected area during off season periods.
1
2
2
32
2
A
4
Step 2:
Fasten the center connector (#3) to the middle of
the legs (#2) by using bolts (#6) and washers (#7).
Make sure that all of the bolts have been tightened
completely and cover them with bolt caps (#8 and
#9). See Figure 2.