ADC AD-310 User manual

ADC Part No. 113316
For replacement parts, contact the reseller
from which the dryer was purchased or
American Dryer Corporation
88 Currant Road
Fall River A 02720-4781
Telephone: [phone] / Fax: [phone]
E-mail: [e-mail]
www.amdry.com
011701D G/rar
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property dama e,
personal injury or death.
Do not store or use asoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to li ht any appliance.
* Do not touch any electrical switch; do not use
any phone in your buildin .
* Clear the room, buildin or area of all
occupants.
* Immediately call your as supplier from a
nei hbor's phone. Follow the as supplier's
instructions.
* If you cannot reach your as supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service a ency or the as
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
dincendie ou dexplosion ou pour éviter tout
domma e matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser dessence ni
dautres vapeurs ou liquides inflammables dans
le voisina e de cet appareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter dallumer dappareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez.
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
az depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rejoindre le fournisseur
de az, appelez le service des incendies.
Linstallation et lentretien doivent être assurés
par un installateur ou un service dentretien
qualifié ou par le fournisseur de az.
AD-310 Phase 7
(with Tilting Options - Natural Gas Only)
Installation Manual

Retain This Manual In A Safe Place For Future Reference
American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is
properly maintained, it will provide many years of safe, efficient, and trouble-free operation.
ONLY qualified technicians should service this equipment.
OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with
the dryer.
The following FOR YOUR SAFETY caution must e posted near the dryer in a prominent location.
AD-310 Phase 7 Tilting
IMPORTANT NOTE TO PURCHASER
Information must be obtained from your local as supplier on the instructions
to be followed if the user smells as. These instructions must be posted in a
prominent location near the dryer.
FOR YOUR SAFETY
Do not store or use asoline or
other flammable vapors or
liquids in the vicinity of this or
any other appliance.
POUR VOTRE SÉCURITÉ
Ne pas entreposer ni utiliser dessence
ni dautres vapeurs ou liquides
inflammables dans le voisina e de cet
appareil ou de yout autre appareil.
We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make
changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or
discontinue models.
Important
For your convenience, log the following information
DATE OF PURCHASE _____________________________ MODEL NO. __________________________________________
RESELLERS NAME _______________________________________________________________________________________
Serial Number(s) ________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
Replacement parts can be obtained from your reseller or the ADC factory. When ordering replacement parts from the factory,
you can FAX your order to ADC at [phone] or telephone your order directly to the ADC Parts Department at
[phone]. Please specify the dryer model number and serial number in addition to the description and part number, so
that your order is processed accurately and promptly.

IMPORTANT
YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and THE GAS
SUPPLY BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MACHINE
TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, or TESTING
OF ANY EQUIPMENT er OSHA (Occupational Safety and Health Administration)
STANDARDS.
WARNING
CHILDREN SHOULD NOT BE ALLOWED TO PLAY ON OR NEAR THE DRYER(S).
CHILDREN SHOULD BE SUPERVISED IF NEAR DRYERS IN OPERATION.
CAUTION
DRYERS SHOULD NE ER BE LEFT UNATTENDED WHILE IN OPERATION.
FOR YOUR SAFETY
DO NOT DRY MOP HEADS IN THE DRYER.
DO NOT USE DRYER IN THE PRESENCE OF DRY CLEANING FUMES.
WARNING
UNDER NO CIRCUMSTANCES should the dryer door switches, lint door switch, heat
safety circuit ever be disabled.
Caution: Label all wires prior to
disconnection when servicing controls. Wiring
errors can cause improper operation.
«Attention: Lor des opérations dentretien
des commandes étiqueter tous fils avant
de les déconnecter. Toute erreur de
câblage peut étre une source de danger et
de panne.»

WARNING
The dryer must never be o erated with any of the back guards, outer to s, or service
anels removed. PERSONAL INJURY or FIRE COULD RESULT.
IMPORTANT
PLEASE OBSERVE ALL SAFETY PRECAUTIONS dis layed on the equi ment and/or
s ecified in the installation manual included with the dryer.
WARNING
DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN IN
PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED.
Dryer must not be installed or stored in an area where it will be exposed to water or weather.
The wiring diagram for the dryer is located in the front electrical control box area.

Table of Contents
SECTION I
IMPORTANT INFORMATION ............................................................................... 3
A. Receivin and Handlin ............................................................................................................... 3
B. Safety Precautions ...................................................................................................................... 4
SECTION II
SPECIFICATIONS/DIMENSIONS and COMPONENT IDENTIFICATION/
LOCATION ................................................................................................................. 6
A. Specifications (Natural Gas Only) ............................................................................................... 6
B. Dimensions and Component Identification/Location ..................................................................... 7
SECTION III
INSTALLATION PROCEDURES ......................................................................... 10
A. Reassembly of Dryer ................................................................................................................ 10
B. Location Requirements ............................................................................................................. 20
C. Fresh Air Supply Requirements ................................................................................................. 21
D. Exhaust Requirements ............................................................................................................... 22
E. Compressed Air Supply System ................................................................................................ 27
F. Electrical Information ................................................................................................................ 29
G. Gas Information ........................................................................................................................ 32
H. Water Supply Connection For Optional Sprinkler System .......................................................... 35
I. Preoperational Tests ................................................................................................................. 35
J. Preparation For Operation/Start-Up ......................................................................................... 37
K. Shut Down Instructions ............................................................................................................. 38
SECTION IV
SERVICE/PARTS INFORMATION ...................................................................... 39
A. Service ..................................................................................................................................... 39
B. Parts ........................................................................................................................................ 39
SECTION V
WARRANTY INFORMATION .............................................................................. 40
A. Returnin Warranty Card(s) ...................................................................................................... 40
B. Warranty .................................................................................................................................. 40
C. Returnin Warranty Part(s) ........................................................................................................ 40

SECTION VI
ROUTINE MAINTENANCE .................................................................................. 42
A. Cleanin ................................................................................................................................... 42
B. Adjustments ............................................................................................................................. 44
C. Lubrication ............................................................................................................................... 44
SECTION VII
COMPONENT SYSTEM DESCRIPTIONS........................................................ 4
A. Basket (Tumbler) Drive System ................................................................................................. 45
B. Basket (Tumbler) ...................................................................................................................... 46
C. Air Blower Drive System .......................................................................................................... 46
D. Safety Devices .......................................................................................................................... 46
SECTION VIII
BURNER and BASKET (TUMBLER)/LINT CHAMBER MANUAL RESET
HI-LIMIT INSTRUCTIONS ................................................................................... 48
SECTION IX
DATA LABEL LOCATION/INFORMATION ...................................................... 49
A. Data Label ............................................................................................................................... 49
SECTION X
PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT
COMPONENTS ....................................................................................................... 1
SECTION XI
PHASE 7 OPL SYSTEM DIAGNOSTICS ........................................................... 3
A. Dia nostic (L.E.D. Display) Fault Messa es .............................................................................. 53
B. I/O Board Input and Output L.E.D. Indicators .......................................................................... 55
SECTION XII
TROUBLESHOOTING ........................................................................................... 60
SECTION XIII
OPTIONAL SPRINKLER SYSTEM COMPONENTS ...................................... 67
Optional Sprinkler Circuit Components ........................................................................................... 67
Sprinkler Option Temperature Controller Settin s ............................................................................ 69

3
SECTION I
IMPORTANT INFORMATION
A. RECEIVING and HANDLING
The dryer is shipped in a protective stretch wrap cover with protective cardboard corners and top cover (or
optional box) as a means of preventing damage in transit. Upon delivery, the dryer and/or packaging, and
wooden skid should be visually inspected for shipping damage. If any damage whatsoever is noticed, inspect
further before delivering carrier leaves.
Dryers damaged in shipment:
1. ALL dryers should be inspected upon receipt and before they are signed for.
2. If there is suspected damage or actual damage, the trucker’s receiptshould be so noted.
3. If the dryer is damaged beyond repair, it should be refused. Those dryers, which were not damaged in a
damaged shipment, should beaccepted, but the number received and the number refused must be noted on
the receipt.
4. If you determine that the dryer was damaged after the trucker has left your location, you should call the
delivering carrier’s freight terminal immediately and file a claim. The freight company considers this
concealed damage. This type of freight claim is very difficult to get paid and becomes extremely difficult
when more than a day or two passes after the freight was delivered. It is your responsibility to file freight
claims. Dryer/parts damaged in transit cannot be claimed under warranty.
5. Freight claims are the responsibility of the consignee, and ALL claims must be filed at the receiving end.
ADC assumes no responsibility for freight claims or damages.
6. If you need assistance in handling the situation, please contact the ADC Traffic Manager at [phone].
IMPORTANT: The basket (tumbler) section of the dryer must be transported and handled in an
upright position at ALL times.

4
B. SAFETY PRECAUTIONS
WARNING: For your safety, the information in this manual must be followed to minimize the
risk of fire or explosion or to prevent property damage, personal injury, or loss of
life.
WARNING:The dryer must never be operated with any of the back guards, outer tops,
or service panels removed. PERSONAL INJURY or FIRE COULD RESULT.
1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
2. Purchaser/user should consult the local gas supplier for proper instructions to be followed in the event the
user smells gas. The instructions should be posted in a prominent location.
3. WHAT TO DO IF YOU SMELL GAS...
a. DO NOT try to light any appliance.
b. DO NOT touch any electrical switch.
c. DO NOT use any phone in your building.
d. Clear the room, building, or area of ALL occupants.
e. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
f. If you cannot reach your gas supplier, call the fire department.
4. Installation and service must be performed by a qualified installer, service agency, or gas supplier.
5. Dryer(s) must be exhausted to the outdoors.
6. Although ADC produces a very versatile dryer, there are some articles that, due to fabric composition or
cleaning method, should not be dried in it.
WARNING: Dry only water washed fabrics. DO NOT dry articles spotted or washed in dry
cleaning solvents, a combustible detergent, or “all purpose” cleaner.
EXPLOSION COULD RESULT.
WARNING: DO NOT dry rags or articles coated or contaminated with gasoline, kerosene, oil,
paint, or wax.
EXPLOSION COULD RESULT.
WARNING: DO NOT dry mop heads. Contamination by wax or flammable solvents will create
a fire hazard.

5
WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or
similarly textured rubber materials. Drying in a heated basket (tumbler) may
damage plastics or rubber and also may be a fire hazard.
7. A program should be established for the inspection and cleaning of lint in the heating unit area, exhaust
ductwork, and inside the dryer. The frequency of inspection and cleaning can best be determined from
experience at each location.
WARNING: The collection of lint in the burner area and exhaust ductwork can create a
potential fire hazard.
8. For personal safety, the dryer must be electrically grounded in accordance with local codes and/or the
National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in Canada, the Canadian Electrical
Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
NOTE: Failure to do so will VOID THE WARRANTY.
9. UNDER NO CIRCUMSTANCES should the dryer door switches, lint door switch, heat safety circuit
ever be disabled.
WARNING: PERSONAL INJURY or FIRE COULD RESULT.
10. This dryer is not to be used in the presence of dry cleaning solvents or fumes.
11. Remove articles from the dryer as soon as the drying cycle has been completed.
WARNING: Articles left in the dryer after the drying and cooling cycles have been completed
can create a fire hazard.
12. READ and FOLLOWALLCAUTION and DIRECTION LABELS ATTACHED TO THE DRYER.
13. For safety, proper operation, and optimum performance, the dryer must not be operated with a load less
than sixty-six percent (66%), 204 lbs. (92.53 kg.) of its rated capacity.
WARNING: YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and
THE GAS SUPPLY BEFORE ANY COVERS or GUARDS ARE REMOVED
FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING,
ADJUSTING, INSTALLATION, or TESTING OF ANY EQUIPMENT per
OSHA (Occupational Safety and Health Administration) STANDARDS.

6
MAXIMUM CAPACITY (DRY WEIGHT) 310 lbs. 141 kg
BASKET (TUMBLER) DIAMETER 62-1/2" 158.75 cm
BASKET (TUMBLER) DEPTH 60" 152.4 cm
BASKET (TUMBLER) VOLUME 106.5 cu. ft. 3.02 cu. m.
DRIVE MOTOR 5 HP 3.73 kw
DOOR OPENING (DIAMETER) 36-3/4" w x 43" h 93.3 cm x 109.2 cm
DOOR SILL HEIGHT - LEVEL 36-1/2" 92.71 cm
COMPRESSED AIR VOLUME * 11 cfh 0.31 cmh
COMPRESSED AIR CONNECTION 3/8" F.P.T.
VOLTAGE AVAILABLE 208-600v 3ø3, 4w 50/60 Hz
BLOWER MOTOR 15 HP 11.25 kw
HEAT INPUT 1,125,000 btu/hr 283,500 kcal/hr
APPROX. WEIGHT (UNCRATED) 5,100 lbs. 2,313 kg
AIRFLOW 6,500 cfm 184 cmm
INLET PIPE SIZE 1-1/2" F.P.T. (1)
Shaded areas are stated in metric equivalents
SECTION II
SPECIFICATIONS/DIMENSIONS
and COMPONENT IDENTIFICATION/LOCATION
A. SPECIFICATIONS (Natural Gas Only)
NOTE: ADC reserves the right to make changes in specifications at any time without notice or
obligation.
NOTE: Dryers must be provided with a clean, dry, and regulated 80 PSI +/- 10 PSI (5.51 bars +/-
0.68 bars) air supply (equivalent volume = 11 cfh [0.31 cmh]).
Gas **
*Air volume requirement is 11 cfh (0.31 cmh) for tilting models.
** Tilt gas dryers must be provided with clean, dry, and regulated air at 80 PSI +/- 10 PSI (5.51 bars +/- 0.68
bars).