Addonics Technologies UDFHNVM7 User manual

CONTACT US
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 5:00 pm PST
Phone: [phone]
Email: http://www.addonics.com/support/query/
www.addonics.com
Phone: [phone]
Email: http://www.addonics.com/sales/query/
1:7 NVMe/Flash/HDD duplicator
Model: UDFHNVM7
Default settings on the duplicator:
Copy – set to WHOLE MEDIA. This setting copies everything in the source drive to the
target drive sector by sector. This setting ensures a good copy of any drives: boot drive,
blank drive, encrypted drive or drive with any file system.
To speed up the copying, you may change the setting to SYSTEM and FILES. This setting
skips copying sectors with no recognizable data. This is only for drives that have the
following file system: NTFS, FAT/16/32, eXFAT, HFS, EXT3/4 or XFS. This setting is not
recommended for copying boot drive as certain boot sectors may not be copied correctly.
Performance – set to SPEED for best performance. May encounter compatibility issue with
certain SSD or old HDD. Should that occur, try to change the setting to BALANCE or
COMPATIBILITY.
Please review the Compact USB Duplicator Controller User Manual for all the detail
settings.
Making duplicates
Power up the unit by pressing on the ON/OFF button at the front lower right- hand corner.
Once the unit is ready, the LCD should display
1. Copy
Source not ready
The unit is now ready. Attach an SSD to the source USB port and as many as seven SSDs to
the target USB ports. After a few seconds, the LCD should display the number of target
drives detected. Press the OK button on the LCM control panel to start the copying.
Reloading NVMe SSD onto the docking station – When loading a new NVMe SSD onto the
docking station, unplug the corresponding USB cable from the duplicator and re-attach the
cable. This reinitializes the USB port to detect the new NVMe SSD. Alternatively, the
duplicator can be restarted to detect all the attached SSDs.

www.addonics.com
Technical Support (M-F 8:30am - 5:00pm PST) Phone: [phone] Email. www. Addonics.com/support/query/
Loading NVMe SSD onto the docking station
Front view
Connect the 8 NVMe to the USB adapter on the Compact USB duplicator as
shown in diagram above using the included USB-C cables and the USB-A
male to USB-C adapters
Rear view
Step 1
Step 2
Package content:
•1:7 Compact USB duplicator main
unit (model: UDFH7-E)
•NVMe docking station with eight
(8) NVMe SSD to USB 3.1 adapter
(model: M2NVM8DS)
•One power cord
•Eight (8) 12” USB – C cables
•Eight (8) USB-A to USB-C adapters
(model: ADU3MUCF)
•One aluminum enclosure, screw
drive and a set of screws (for using
the NVMe SSD to USB 3.1 adapter
as an external USB drive)
•This quick start user guide
•Compact USB duplicator controller
user guide
Attaching the NVMe SSD to the duplicator
1. Turn off the duplicator
2. Install the NVMe SSD into each adapter on the docking station as shown
in the diagram above. There is no special tool required. The NVMe SSD is
temporary secured in the adapter by the hold down clip on the side of
the adapter.
3. Connect the adapter with the source SSD to the source USB port and the
adapters with the target SSDs to the target USB ports on the USB
duplicator, using the USB-C cables and the USB-A male to USB-C adapters
that come with the unit. (see the Front View diagram for reference)
4. Power on the duplicator. Wait for the LCD display to indicate the # of
devices detected and press the OK button to start the duplication.