ADEMCO 1025 User manual

FADEMCO~
GENERAL INFORMATION:
The No. 1025 Alarm Processing Center is a local alarm panel with the following features:
Basic Supervised Protection Zone for Normal and Fast Acting Perimeter and Interior Devices.
Entry/Exit Zone with 45 (or 30) Second Entry and Exit Delay Times. Supervised.
24 Hour Audible Emergency (Panic) Circuit,
LED Indication of Zone Status, A.C. Power and Alarm Memory (indicates alarm has taken place and bell has timed off).
Outputs for Bell(s) or Electronic Siren(s), Closure of Dry Contacts, and (Optional) Early Warning Horn.
Automatic Alarm Cut-off and Restore.
Bell and Battery Test Switch.
Includes Low Voftage Plug-in Transformer and Built-in Rechargeable Power Supply.
System Turned ON and OFF from a Keyswitch (e.g.: No. 4235). Remote Station(s) may be used instead (see ACCES-
SORIES at end of these instructions).
The cabinet provides room for optional installation of a digital communicator (e.g.: No. WS669, WS670,678,679 or
680) or other accessories (see ACCESSORIES herein).
INSTALLATION AND WIRING: See Figure 1
Do not connect thebattery or plug-in transformer until all other wiring has beencompleted. Use of twisted wiring
is recommended for all runs, for greater immunity to unwanted induced voltage.
A WHITE jumper is provided at the top of the chassis. If this jumper is cut it will shorten the factory provided entry delay,
exit delay and “bell” cut-off times as tabulated in Figure 1.
Terminals Wiring Information
123.4
Basic Protection Zone (Double Loop): Run a pair of wires from terminals 1 and
2 to all protection points in this zone and return to terminals 4 and 3 respectively.
Connect protection devices into the two loops as follows:
2.3 Normal Response Loop (Basic Protection Zone):
Connect closed circuit con-
tacts of normal acting devices (such as magnetic contacts, foil, etc.) in series with
this loop. Maximum permissible resistance: 300 ohms.
194
Fast Response Loop (Basic Protection Zone): Connect closed circuit contacts
of fast acting devices [such as vibration contacts (e.g.: No. 11), glass protection
devices (e.g.: No. 9) and photoelectric units without built-in delays] in series with
this loop.
56
Maximum permissible resistance: 300 ohms. To lessen the chance of false alarms,
the fast response loop should not contain exposed metallic contacts.
Notes: An opening in either of those loops, or a short between loops will cause an
immediate alarm when the system is ON.
Devices with open circuit contacts (such as mats) may be connected
between these loops (or into the fast response loop with an Ademco No.
602 Mat Coupler).
Entry/Exit Zone: Connect closed circuit contacts on the entry/exit door as well as
interior contacts or sensors located in the path between the exit door and the con-
trol in a series wiring loop across these terminals. Maximum .permissible loop
resistance: 300 ohms.
This zone provides entry and exit times of 45 seconds each (30 seconds if the
WHITE jumper is cut per Fig. 1).
For additional security (against shorts) the Basic Protection Zone’s normal
response loop may be routed along with the entry/exit loop as shown in Figure 1. A
short between these loops when the system is ON, will result in an alarm
after the entry delay. 506 -
497
lNSTAlLATlllilN~IOE
lNSTRUCTIONS
El
_
ALARM PROCESSING
CENTER :p

All interconnections must be made with. U.L. listed limited energy cable.
CUT JUMPER
GROUNDCABINET TO COLD ,WATER,PIPE’OR ELECTRICAL
c BOX, TO AVOID POSSIBLE STATIC VOLTAGE DAMAGE.
AS MAT) CABINET
. - A *Max. total load permitted to “bell” plus “acces-
BASIC
MOUNTlNG
SCREW
pRTsm
sories” (on alarm) is 2A.
**If using remote station(s) in lieu of keyswitch con-
I ““’ 4L=J’CLOSE
ON 1
ALARM
LOOP STATUS SIG1
OR ACCESSORY
IAL POST
APPLICATIONS)
I
(6v. DC
I
6V.. 2SAH
TO24HR
110 v. AC
OUTLET
LISTED CLASS I3
XFMR (12V.. 6VA)
trol, follow instructions accompanying item(s)
used (e.g.: Nos. 244,245.215/216,22?/228.815/816,
5241).
FIGURE 1: Field Connections
* - - - - - - - Optional routing of normal loop (for
additional entry/exit loop security).
7.6
9,W+),W-)
Emergency (Panic) Switches: Connect locking type open circuit emergency
switches (such as No. 264,266,268 or 269) in parallel across these terminals.
Operation of an emergency switch at any time (system OFF or ON) ,will cause the
alarm bell(s) to ring and the output contacts to close. Alarms activated from emer-
gency switches do not cut off until the switches are reset.
No. 706Mini-Howler (Optional): Connect as shown in Figure 1. The mini-howler
will sound: 1) During the entry delay period. 2) In case of accidental closing with
the entry/exit zone open. 3) lf an alarm occurs in the entry/exit zone while the
panel is ON. In this last case, the No. 706 will sound until the alarm bell cuts off or
the entry/exit loop returns to normal (whichever occurs leer). When sounding, the
No.706 draws 50 ma.
507
498

IO,11
Keyswitch: Connect a keyswitch with key removable in “make” and “break” posi-
tions (such as No. 4235) across these terminals (OFF Position: Contacts
CLOSED, ON Position: Contacts OPEN). A knockout is provided on the cover of
the cabinet for mounting. If this keyswitch is located remotely it should be kept
within the protected area.
Instead, remote station(s) showing system status may be used, via an appropriate
adapter. See ACCESSORIES.
N.O. Dry Contacts: These contacts may be used to trip a digital communicator,
telephone dialer or as desired. The contacts close on alarm (burglary or emer-
gency) and open upon bell cut-off (burglary) or when emergency (panic) switches
are manually reset. (The contacts do not close during bell test.) Rating: 2A, 28V.
DC/l 1OV.AC. See CAUTION at end of these instructions..
6V. DC For Accessories: Up to 220 ma continuous load can be connected to
these terminals for items such as those described in ACCESSORIES. During
alarm, up to 2 amperes total combined load may be supplied by these and the
alarm bell terminals 15 and 16.
6V.DC Bells or Electronic Sirens having a combined total rating of 2 amperes
(less any alarm load connected to term. 14 and 20) may be connected in parallel
across these terminals. If electronic sirens are used, observe polarity.
Note: Except during an emergency (panic) alarm, cut-off occurs after approxi-
mately 12.minutes (8 minutes if the WHITE jumper is cut per Fig. 1). The
Alarm Memory LED remains lit until the panel is disarmed. If the protective
circuits are then normal, the unit will report any subsequent alarm condition.
Power Input, 12V.AC: Turn the keyswitch to its OFF position and connect these
teninals to the output terminals of the No. 1320 Transformer. Do not plug in the
transformer yet:
Used with remote (arming/disarming) station accessories (minimum recom-
mended load resistance: 50K ohms).
Ground the cabinet to a cold water pipe or electrical box.
Standby Battery: After all other wiring is completed, and with the keyswitch
OFF (dosed), connect to the battery when ready to proceed with TESTING
12,13
14( + ),20( - )
W+),W-)
17,18
LOOP STATUS
SIGNAL POST
GROUND
BLACK, RED
LEADS WITH
CONNECTOR AND CHECKOUT.
ALARM PROCESINGCENTER 1025
ZONE STATUS
Basic
Protection
Egy
(3ii5-1 ALARM DEVICE MFG. CO.
SYOSSET, N.Y.
IMPORTANT:
- CONDUCT
BELL TEST
REGULARLY
FIGURE 2: lndica tors
TESTING AND CHECKOUT:
Perform these tests after the wiring and connections described in the previous section have been completed.
The keyswitch should still be Off and the standby battery must be connected.
1. Plug the transformer into a 1lOV.AC outlet that is ON 24 hours a day. The A.C. POWER LED should light. CAU-
TION: DO NOT OPERATE ANY OTHER EQUIPMENT SIMULTANEOUSLY FROM THIS TRANSFORMER. DAM-
AGE TO THE TRANSFORMER AND/OR EQUIPMENT OR IMPROPER SYSTEM OPERATION COULD RESULT.
2. Observe the Zone Status LEDs. Neither will be lit if the protective loops are properly wired and all contacts are
properly set.
508
499

3.When both Zone Status LEDs are out, do the following,and observe the appropriate LED light in each case:
a. Open the fast response loop momentarily. The Basic Zone LED should light while the loop is open.
b. Open the normal response loop momentarily. The Basic Zone LED should lightagain.
c. Open the entry/exit loop momentarily. The Entry/Exit Zone LED should light.
d. Short the fast and nonal loops momentarily. The Basic Zone LED should light momentarily.
e. Short the normal and entry/exit loops momentarily/The Entry/Exit LED should light momentarily.
4.fast the Bell(s) and Standby Battery by depressing the BELL TEST switch momentarily. The bell(s) should ring
while the switch is depressed. Any devices connected to the dry contacts will not be activated.
Note: The battery may not be fully charged. Ifthis test is tried with a low battery, there will not be enough power to
ring the bell. Let the unit charge (transformer plugged in) for at least one half hour if the battery is low.
5.Test the Emergency (Panic) Circuit by momentarily shorting terminals 7 and 8 or tripping an emergency switch.
The bell(s) should ring only as long as the short remains and any devices connected to the dry contacts
will be activated.
6. Turn the system ONand simulate leaving the premises by following the procedure given in the OPERATION
section.
.Note: If an alarm is tripped during testing, the bell(s) can be silenced by turning the keyswitch to OFF.
7. Simulate entering the premises and turn the system OFF by following the procedure given in the OPERATION
section.
OPERATION:
Note: The Zone Status LEDs on the panel will go on and off as the protective loops open and close during normal operation
of doors, windows, etc., while the system is OFF.
WhenTurning System ON:
1. A.C. power LED should be lit at all times. If out, AC. failure to unit is indicated.
2.Zone Status LEDs should be off. If lit, protective loop is not set properly.
CAUTION: If either Zone Status LED is lit, turning the keyswitch ONwill cause an alarm immediately in the case of
the Basic Protective Zone or after 90 seconds (exit plus entry delay time) for the Entry/Exit Zone (60 seconds if the
4B
WHfTE jumper has been cut). In the latter case, the No. 706 Mini-Howler (if installed) will sound a warning immedi-
ately that an alarm can be avoided if the keyswitch is returned to OFF before 90 (60) seconds have expired.
3. Depress BELL TESTSwitch to test bell, standby battery and power supply.
IMPORTANT: For continual assurance that bell, battery and power supply are in proper working order, regular
performance of BELL TEST is advised. This is particularly important when remote arm/disarm
keyswitches without LEDs.are,used.
4. Turn Keyswitch ONto arm system. Leave via entry/exit door within 45 (30) seconds.
WhenTurning System OFF:
1. Entar only through entry/exit door. If a No. 706 Mini-Howler has been installed, it will sound during the entry
delay period.
2. Note if ALARM MEMORYLEDon panel is lit (it will be if an alarm has taken place).
3.Turn keyswitch Off before end of entry delay period.
ACCESSORIES:
IMPORTANT: Accessories may be used, provided they do not result in a total 6V. DC continuous auxiliary load of more
than 220 ma (except as noted below) being drawn from the panel. Total current on ALARM (including
alarm sounding device) should not exceed 2amperes.
Instaad of using a keyswftch to control the panel, up to 4 remote stations (e.g.: No. 214.246,246R or 5248) may be
usedviaa No. 244 Remote Station Adapter (each remote station shows system status via a single LED). Current
Draw, No. 244with 1remote station: 11.5ma (each add’1remote station :9.5ma).
Alternatively, the following are available for coded pushbutton control of the No. 1025:
No.2l6 Two Wire Digital Station with Panic Circuitry (up to 4 can be used via a No. 216Adapter). Current Draw,
No.216with 1No. 215: 11.1ma (each add’1No. 215:9.1ma).
No.227 Single Button Digital Remote Station (up to 5 can be used, via a No.228Adapter). Current Draw, No. 226
with 1No. 227: 14ma (each add’1No. 227: 6 ma).
No.5241‘Self-contained Digital Remote Station with Panic Circuitry (single unit only can be used).Current Draw:
12ma. 509
500

Other available accessories include:
No. 245 Remote Station Adapter and Supervised Fire Circuit: Permits the addition of up to 4 remote keyswitch sta-
tions on a 2 wire circuit, momentary panic switches (e.g.: No. 219) and a supervised fire circuit to the control. Current
Draw: 7 ma plus 9.5 ma per remote station plus Currentfor smoke or combustion detector power and No. 633 to _<, ..,
Supervisory Module.
No. 262 Fire Module: Permits the addition of an unsupervised fire circuit to the control. Current Draw: 0 ma plus cur-
rent for smoke or combustion detector power.
No. 263 Supervised Fire Module: Permits the addition of a supervised fire circuit to the control with optional No. 706
Mini-Howler annunciation of fire trouble. Current Draw: 5ma plus current for smoke or combustion detector
power and No. 633Supervisory Module.
No. 688 Opening/Closing Switching Module: Interfaces between the control and a digital communicator to signal
the communicator to send opening and closing messages as the control is disarmed and armed. Current Draw: 2 ma
with high impedance constant load.
No. 1034Zone Expansion Center: Permits additional protection zones to be added to the control by expanding a sin-
gle protection zone to 4 zones (including a “day” zone option on 2 of the zones). Current Draw: 20 ma.
No. 1035Day Zone Adapter: Permits the addition of a “day” or “24 hour” zone to the control with day sounder annun-
ciation of disturbances. Current Draw: 6 ma.
Complete information accompanies the above accessories. -
SPECIFICATIONS
Physical: . Width: 6” (20.3 cm)
Height: 15” (38.1 cm)
Depth: 3” ( 7.6cm)
c
Electrical: Voltage: 12V. AC (from No. 1320 Plug-in Transformer)
Current (per loop): 4 ma
Maximum Resistance (per loop): 300 ohms
6V. DC Bell Circuit Output: 2 A maximum (incl. accessories)
(3 A Fuse, No. 90-l 2)
6V. DC Accessories Circuit Output: 220 ma max. continuous ;-
2 A max. on alarm (incl. bell circuit) ,!
(3 A Fuse, No. 90-l 2)
Output Relay Contacts: SPST, Rating: 2 A at 26V. DC, 11OV.AC r
Standby: 6V Sealed Lead Acid Rechargeable Battery, 2.5 A.H. (Ademw
No. 496) Up to 60 hrs. standby, dependent upon continuous
load supplied to accessories.
I-- ~~~-~~~ - .-- -~~ ~ MAXIMUM STANDBYTIMES WfTHVARIOUS 1
AUXILIARY CIRCUITCONTINUOUSLOADS’
ma: 0 50 100 150 200 220
Hrs: 60 26 14 9.5 7 6
*Loads in addition to control panel and loop currents.
I
CAUTION
Digital Communicators (or Dialers) shall not be set or programmed to place a call to a police station
number which has not been specifically assigned by that police station for such service. I
510
50.1

511
502