ADEMCO Vista 4120 User manual

4120EC
INSTALLATION
INSTRUCTIONS

CONGIWI’ULATIONS
on your purchase of the VI’S?A4120EC! “- ’ f-3
“~.-’
The purpose of theseInstallation Instructions is to give you abrief overview of
the VISTA 4120EC,sy$em, and provide instructions for installing a basic system.
As always, ADEMCO is there for YOU! Our SALESand TECHNICAL SUPPORT
staff are eager to assistyou in any way they cansodon’t hesitate to call, for any
reason! EastCoastTe&zicaI Support:l-800-645-7492(8a.m.-6p.m. E.S.T.)
WestCoastTechnical;Support:7-800458-9469(8a.m.-5p.m.P.S.?‘.)
”
.PLEASE,
Before you call Technical Support, be sure you have:
l Checked all wiring connections.
l Determined that the power supply and/or backup battery are supplying
proper voltages.
l Verified your progr amming information where applicable.
l Noted the proper model number of this product, and the version level (if
known) along with any documentation that camewith the product.
l Noted your Ademco customer number and/or company name.
Having this information handy will make it easierfor us to serve you quickly and
effectively
Again, CONGRATULATIONS, and WELCOME ABOARD!
FORYOUR CONVENIENCE,two easiiy removable
Progamming Forms have been included at the
center of this manual.

INSTALLATION
INSTRUCTIONS
bkDEMC0
4120EC

CONTENTS
Generaf information 2
Remote Programmingand Controls, 2
Zone Types AvailableforSelsctio~ 3
CDiilt sewrity codes 3
Terminals 5
Wiring Connections 7
Mountingthe consoies 7
Programmingthe Security Control 7
r-*dress Programming
na 8
Programming Form
Testing the System 13
specifiibna 13
Beauitycontrol 12
4127 RemoteCon&a 13
5330 Remote Console 13
4137 Remote Console 13
Acwssories
14
The Limitationsof this
Abrm System 15
LimitedWarranty- 16
Dbgrams
Summary Of Connections 6
Mountingthe Circuit Boar- 4
Mountingthe M 5
t- MARGIN UNES INDICATE PRINCIPAL CHANGES IN THIS ISSUE
GENERAL INFORMATION
The VISTA (No. 4120) is a microprocessor-based security
wntrol whii provides up to 8 wired zones inthe basii product.
The security control is housed in a wall-mounted metal cabinet
measuring 12-1R’ (318 mm) wide x 14-l= (368 mm) hiih x 3’
C16mm)dee9,andcanbeusodrvithaaonsOleequippedwitha
muftiiunction la-key digital keypad and a numeric and fixed
English status LCD diipiay (4127). Optionally, a No. 4137 may
be used or a No. 5330 Alpha Console may be used with the
control to provide programmable English language zone
descrbtors and status indications.
Connections to the aea~ritycontrol are made via a 25-terminal
connector bbck whii is us& to interlace to the wired hops.
plug-in transformer, telephone fine, remote consoles, external
alarm sounder(s), etc.
The security control can be easify programmed from a 4127
remote console. Programmed options to establish spscifii alarm
and reporting features are stored in electrically erasable. non-
volatile EEROM memory. This means that the unit can be
reprogrammed many times (unlike units equipped with PROMS)
and that information whii has been programmed will not be
bst in the event of a complete bss of power.
The system provides communication capability (central station
reporting, etc.) over existing telephone lines.
This system includes an alarm output rated at 2.8 amps.
Throughout the manual, wherever reference I8 mede to
Alarm Output Ratings, they aeeume a fully charged battery
h connected unbsa otherwise statid (e.g. UL ratings).
zalo ch8metoristics
&ne 1: Programmable Zone. may be used as EOLR
supervised Fire Zone (supports three Z-wire
Smoke Detectors), or may be used as a non-fire
zone, 350500 msec response.
&noa 2-2: Programmable Zones, N.O. or N.C. sensors, 350-
500 maec response (Zones 2-7). Zone 8 can be
selected as slow or fast response (1O-15msec) I
*
REMOTE PROGRAMMING AND CONTROL
The No. 4120 allows the installer to call it using switched
network phone tines so that the controVcommunicator can be
remotely programmed and/or commanded from an IBM
wmpatibb Personal Computer (PC). See Note 2 under Remote
CapablNitieaInthis section.
Accesaii of the Ho. 4120 from a remote location is protected
against compromise by someone attempting to defeat the
system, using 4 levels of sea&y protection:
1.
2.
3.
Socurtty Cod. Handshake An 8diiit Central Stat-km
IDcodemustbsmatchedbetweentheNo.4l2Oarulthe
central Btation.
Hang-up and callback Calling the No. 4126 does not
directly albw programming, as a successful handshake
merefy results in the No. 4120 breaking the phone line
connection and then calling back the (internally stored)
central station set-vim phone number.
Data Encryptlon: Data passed between the central
statPnandtheNo.4120isenayptedforsearritysothatit
is very difficult for a foreign device tapped into the phone
line to take over communication and substitute system
compromisii information.
4. Contra1 StatIon Advlaory Note: Any condition that
causes the system to initiate a call back to a telephone
number from whii it can be reprogrammed or corn-manned
(in tact, even for a local reprogramming of the EEROM)
causes a unique repon to be sent to the central station’s
alarm bggii diiital receiver.
Hoto: In situations where a service person is on-site and the
system is installed inside a PABX. it is possible to initiate
a download from the protected premises by keying
@atalier or master security code] + [#I + 11).
Equipment Required
At the prrmlwr: 4120
At the cmntral st&on (or the instaileVsofficeMme):
An IBM PC compatible computer, a Hayes brand Smartmodem
1260 (Level 12 or higher external or Level 1.1 or higher internal
style), No, 4130PC Downloading Software Diskette, and
appropriate interconnecting cables.
Remote Capabilities (See Note 2)
Programming:
All programming functions accessible from the unit’s keypad.
2

There are two types of commands that can be issued to the
system:
1.Control Commands-
- To Armthe System inthe Away Mode*flr
- To Disarmthe System.m
-ToEypassaZono
- To Forcethe Systemto Accapt a New Program
Download
- To Shut Down Communication(dialer) Functions
(non-psymentof monftorfngfees in an owned system)
- To Shut Down all Secur&ySystemFunctions (non-
paymentfor a leased system)
- To fnhibit Local KeypadProgramming (praventstake-
over of your accounts)
2. Status Commands -
-To Causethe Systemto Upbad a Copy of its
Resident Programto the central station.
- To Read System Status:
Arming Status
Ready Status and Current Faults
PreseMe of Alarms
Presenceof Troubles
AC Power Status
Bypsss Status and Current Bypasses
wotos
1. If the system is programmed for open/dose reporting by
user. User#t will be reponed.
2. After the 4120 and the PC have established valid
communication, each console will become inactive. The
4120 will resume the normal security functions after it is
commanded to hang up. See the 4130PC instructbns for
details.
The detailed operation of the functions described bebw is
0 covered in the Installation Instructionsfor the 4130PC
Downbad Software Diskette.
- To Read List of FaultedZones
-ToReadListofBypassedZones
‘-ToReadlJstofZonesCurrentlyinAlann
-ToRaadListofZonaaCurrentlyinTroubte
BemoteDammunicaUon Spacifkations
l Program Downbad Tie - 1 minutefor a complete
l Tmsotaf Time Induding Call UpGall-Badr 3-4
minutes
Romota Command/Prog~mlng Adviawy Noteaz
l Alarm and Trouble Reporting are disabled during the
timathat the system Snd the central station are linked to
each other for the described functions, following a valid
exchange of codes.
l Keypad entries are fgnored during the same time inter-val
cited above.
l Should an alarm transpire during the remote progranVcontrol
interval, the system would not response to the alarm
amdlln.
l A copy of the program downloaded may be produced from
the IBM PC compatible computer, using the product-s
internal report generator, when an optional printer is
connected.
ZONE TYPES AVAILABLE FOR SELECTlON
For each zone used, one of the following zone types mustbe
selected:
1.
e
3.
4a
6.
6.
7.
8.
0.
Entry/Exit Burglary. Assigned to sensors on doors
through whii entry and exit will normally take Placewhen
the system is armed.
Not used
Parlmakr Burglary. Normally assigned to all sensors pn
exterior doors and windows requiring instant alarm.
Interkr, Followor. Delayed alarm only if the Entry)
Exit zone is faulted first; otherwise, produces an instant
alarm. Assignedto zone covering an araa such x9 a foyer or
bbby through which one must pass upon entry to raach the
keypad to dii the system. Designed to provide instant
intrusion alarm in the event an intruder hides on. the
premises prior to the systembeing armedor gains -8s to
the premises through an unprotected area
Trwbk by Day/Alarm by Night. Can be assigned to a
zone which contains a foil-protected door or window (such
as in a store), or to a zone covering a %ensitive’ area such
as a stock room, drug supply room, ek, or other controlled
access area where immediate notification of an entry is
desired. During the disarmed state (day), the system will
provide latched Console annunciation (and central station
report, if desired) of openings or troubles (such as sensor
malfunctions or foil breaks). During the armed state (night),
violations will initiate an alarm.
24Mur Siknt Alarm. Thii type generally assigned to a
zone containing an Emergency button that is designed to
initiate an alarm report to the Central Station, but which
produces no local displays or alarm sound.
2btmur Audible Alarm. This type also assignedto a zone
containing an Emergency button, but which will initiate an
audible alarm in addition to an alarm report to the Central
Station.
240hour Auxlllay Alarm (Console sounder only). This
type assigned to a zone containing a button for use in
personal emergencies, or to a zone containing monitoring
devices such as water sensors, temperature sensors, etc.
Designed to fniiate an alarm report to the Central Statbn
and only provides Console warning sounds and alarm
dww.
Supeniaod Firi (alarm or short/trouble on open). Fire
zone may not be bypassed. On/y uaaale on Zone 1 when
/t Is wired with w) EOL resistor.
40DIGIT SECURITY CODES
InstallerCode
The installer programs the Installer Code initialty as part of the
programming procedure (see ‘Programming the Security
Control). In thii system, the installer is con-sidered to be user
Xl. The installer code permits re-entry into the -ramming
mode (unless ‘98 has been previously usedto exit the
programming mode) and also allows access to the normal
functions of the system. During initii programming, the installer
also programs the Master securitycode intothe system.
[ I[ I[ 1 ] InstallerCode (Useral).
assigned during programming.
3

lnstalbr axfts programming mode with:
99 (albws m-entry intoprogramming mode
with installer code)
OR
-@8 (does not albw m-entry to pngramming
mode unless system b first powered
down and then repowerad). tnstalbr cade
Isdied when thii exit b used.
Maatwsoawltycodu
The Master security oode can be used to assiBn up to six
l acondafy codes (to users #3 - aa); ft can also be used to
lomow all saamdary oodas from the system (indiiualfy). The
persontowhomtheMastercodebassignedbuser12.
Se~ndary secwity codes are assigned &y user 12 (with Master
cda)asfol~
Master Code+000E key+User #(3-$)+BscondaryCode
The system will emit a single beep when each secondary code
has been successfuliy entered.
)Jotw When a secondary code is inadvertently repeated for
diierent users, or one usefs code is another’s duress
oode,the iower user numberwill take priority.
InMdual waondary security codes can be deleted by usar I2
(with MasterCode) asiollows:
Master C&e+CClDE key+User #(3-B)+Master Code
Motar All security codes, master and secondary, permit access
to the systemfor arming, dinning, etc.
WVELE OF MlfwDRlTY FOR SECURlTY CODES
User Can aaabn or doleto
No. &conday cod. 01 usor.
#I (Installer) None
(12
M through #8
##(I None
MOUNTING THE CIRCUIT BOARD
DETAIL SIDEVIEW
OF CLIP AND BOARD
INSTALLED
DETAIL SIDE VIEW OF
CLllPINSTALLATION
A-l CABINET TAB
WITHOUT CLIP
B-f CABINET TAB
WITH HANGING
CLIP ORAlL
OF BOA
INTO SLOTS
EDIEW
rRDINSERTED
cl
‘._ .’
Betoremountingthe~boardbecertainthattheapprO-
priate metal lcnockoub have been removed. DO NOT
ATTEMPT TO REMOVE THE KNOCKOUTB AFTER THE
ClRCUlT BOARD fiAB BEEN INSTALLED.
2. Insertthe top of the circuit hoard into the sbts at the top of the
cabinet. M&e certain that the hoard rests upon the correct row
as indiied in step 2 detail.
1. Hangthetwomountingdipsonthersisedcabinettabs(see 3. swing the base of the hoard into the
mounting clii and secure
the hoard to the cabinet with the accompanying screws (as
step 1 detail A and B). Bustrated in step 3 detail). .n
4

MOUWTIWG THE LOCK
1. Removethe loch knockout on
the control cabinet cover.
Insert the key into the loch.
Positiin the kch in the hole
making certain that the latch
will make contact with the
latch bradset when the door is
2. While holding the bdc steady,
insert the retainer dip into the
retainer slots. Position ciii as
illustrated to facilitate easy
removal.
I)
1:
2:
6:
7:
xj
10:
11:
12:
‘9
UNLOCKED
CLIP
CABINET DOOR BOTTOM
TERMINALS
AC Input from No. 132lITF2 plug-k transformer (16.5
VAlCAl!5;A). In Canadian installations, use
AC Input from No. 132lITF2 plug-in transformer (16-s
VAC. 25VA). In Canadian installations, use No.
1321cN.
Afarm relay output (+), 12 VDC,28A maximum.
Alarm Oulput/Auxilii Power (-) Return.
Continuous AuxiliasylRomote Console Power (RED):
+12VDcat700mA.
Console Data In (GREEN)t.
console Dataout (YELLOW)?
Remote Console Ground (-) (BLACK$.
Ground Start Output (to BLUE LEAD on No. 675
Ground Start Module). or Hiih Site of Zone 1 when
zone is usad as an End-of-Line Resistor supervised
burglary, panic or P-wire smoke detector compatibfe
fire zone. Terminal 12 would net be ueed for Zone 1
when this terminal is used for Zone 1.
Zone 1 Return when tine 1 is programmed (Field ‘41)
as an EOLR supervised zone, a 2,000 Ohm EOLR
should be wired between thii terminal and the hih
aide of the zone on Terminal 9. Zone 1’ High Side
when used with terminal 12wlthout EOLR.
zone 2’
Zones 1 and 2 Return (not wad for Zone 1 if EOLR
la used)
13: Zone3’
14: zonea*
AElAlNER CLIP
(NOTE POSITION)
RETAINER
SLOTS
17: ZoneV
18: Zones 5 and 6 Return.
19: zoner
20: zone 0’.
21: Zones 7 and 8 Return and EARTH GROUND (a proper
earth ground must be provided to protect the system
from llghtnlng and l lectroatatk discharge damage).
E .
241
Hz Rpyl.
Irooming Phone Line (TfP).
25: IncomingPhone Line (RING).
tHome run each consofe. Use no more than 220’ of 1122wire or
55Q of Xl 8 wire.
l Zone that is programmable for use either as a N.C. sensor loop
or as a N.O. sensor loop (in Field -08). Zone response time
during digii communkation may be as bng as one second.
Warning: To prevent the risk of shock, disconnect telephone
line at kko jack More servicing the unit.
RED LEA& Battery (+) - When AC is present, 13.8 MC is being
developed to recharge a Starved Lead Acid or Gel battery and
when AC is absent, 12 VDC current is drawn from the battery.
Batterybad reversal damage protectkn is provided.
ElMIt LUD: Battery (-).
15: Zones 3 and 4 Return.
16: Zone5

9 ti
f-7
I
-
.
#
.
-
(a3wbwmow NWM) bmot
,. . ..
(+I MMd 310!3N03 :03U %r”$P c’
8

WIRING CONNECTIONS
MOUNTING THE No. 4127 CONSOLE(S)
(SeeSummeryof ConnoetfonsDlmgmm)
Important: Do not connect the battery or plug in the AC
transformer until all other wiring connections have been
completed. When pownrbrg up the systsm, ysu must uas
tb foIlswIng ssqusnssz
1.Plug intransformer. 2. Connectthe batten.
Grounding the System
In order for the protective devices in this product to be effective,
Terminal 21 must be terminated in a good earth ground. The
following are examples of good eanh grounds available at most
installatiins:
Metal Cold Water Pipe: Use a noncorrosive metal strap firmly
secured to the pipe to which the ground lead is electrically
connectedand secured.
AC Power Outlet Ground: Available from 3 prong, 125VAC.
power outlets only. To test the integrity of the ground terminal,
use a three-wire circuit tester with neon lamp indiirs, such as
the UL-Listed Ideal Model 61935, or equivalent, available at
mostebctrbal supplystores.
1.
2.
3.
4.
5.
6.
Separate the consob from its bad@ate by removal of the two
screws on the tap and bottom edges.
Use the backplate to mark the positions on the wall for the
screw mounting holes and the cutout fqr the interface wiring.
Use wall anchors for the screws and make the cutout in the
wall no largerthan indicatedon the template. The backplate is
designed to be directly mounted to either a single or double
gang ebctrbal bow.
Pullthe interfacewiring in the wall through the cut-out.
Pass the interface wiring through the opening in the ba&plate
andthen mountbackplateto the wall surface with screws.
Splice the interface wiring to the console wires. Insulated
solderless wire splices (such as Ademco No. 311) may be
usedfor splicing.
Attach the main body of the console to the wall-mounted
bsckplate. The oonsole is properly attached when it is screwed
tothebackp&ebytopandbottomscrews.
PROGRAMMING THE SECURITY CONTROL
Installer options are stored in non-removable, electrically’
erasable, non-volatile EEROM memory. ‘These options must
be programmed for the particular installation to establish its
specifii alarm and repolting features. The security control may
be programmedfrom a remote console.
When pmgramming, the field number will be displayed on the
LCDdiiy; also. each entry is displayed as it is keyed in. After
programming, values that have been entered in each fiikt can
berevbwedand,il necessary,mod&d.
*Note: It Is possibb to program the system at any time - even
at the installeti premises prior to the actual installation.
Simply apply power temporarily to the control and then
programthe unit as desired.
When programmingfrom the consoles notethe folbwing:
1.Enter the -ramming mode by simultaneously depressing
the r] and [W]keys wlthout 30 ssoonds after power Is
rpplbd to the Control, or subsequently by keying the code
4+1+2+Ofolknr&bvde~essionofCODE+O+Okevs.
Once an installer code & p&rammed, use it instead of ihe
default c#le (4120)to gain access to the programming mode.
2~secondsafterenlyintotheprogrammode.Wwillbe
displayed. Following the above display, the system is ready
to awept entrbs for Address 00.
3.To pmgram a data field, key [.I plus Addnu (for example.
l Ol), then make the required entry. To simply review a data
fiikf. key [a) plus Address.
4.When a data field has been completely programmed, the
console will ‘beep’ three times and then automatically
proceed to, and display. the next data field address to bs
programmed if that field is the next sequential address (if not,
key k] plus the address of the next field to be programmed.
5. II the number of diits that you enter in the data field is less
than the maximum permitted (for example, phone number),
then the console will display the last data entered. To
proceed, the next dsta fiild address to bs programmsd must
then be entered (for example. %5).
6.If an address Is bnproperly entered, the console will display
FC. II a program entry is improperly entered (for example, a
larger number than that which is permitted), the console
display will go blank. In either case, simply re-enter the
number.
ENTER 1. POWER UP, then depress p] and [#J
PROGRAMMING simultaneously within 30 seconds of
MODE: powering up.
OR
2. Initiilly, Key: 4 + 1 + 2 + 0 plus CODE
key+O+O.
OR
3.After Installer Code is programmed.
key: Inataller Code +CODEkey +O+O.
Notea: Type 3 method of re-entry to the pro-
EXm PROGRAM-
MING MODE:
l 99
giamming mode is inhibited if -the
programming mode is exited via use of
la6.
Type 1 method of entry can always be
used, unless console program-ming has
been locked out by the remote
downbader.
(always albws m-entry to program-ming
mode via Type 3 entry method above),
unless console programming has been
locked out by the remote downloader).
‘98 (inhibits resntry to programming mode
via Type 3 entry method).
Note: When the programming mode is exited,
RESTORE
FACTORY DFLT
AfXANCE TOFIELD:
‘96
[*]+ADDRESS (e.g., 01.10.21 etc)
PROGRAMFIELD:
ERASE FIELDS:
READ FIEU):
(*]+ACORES$folbvmd by dataenttfg
(.]+ADDRESS+[.] (only applies to
Addresses 31 thru 35).
[#I + ADDRESS
SPECfAL MESSAGES
OC = OPEN CIRCUlT (no communicatiin betweenthe Console
andthe Control).
FC I FtELD CODE ERROR (programentry m’&ake, reenter
the data).
NOTE: The following programming information containsthe
factory default settings within the brackets [ 1.
a 1 minute set-up period must elapse
before the system can properlyfunction.
7

COMMENTS: Thii 4diiff (0-Q)
code is resewed for coiitp&y Use.
Thisistheonlyatdethatcanhe
used to enter the Program mode
from the console. tt cannot be
used to enter secondary codes.
Thiioodemaynotheused ifpto-
ramming mode is exited by a ‘98.
MASTER SECURITY CODE
[112][314]
COMMENTS: Enter4 digfts, O-9
(entry of all 4 is mandatory). Use
of a T in the last position inhibits
the Ambush feature.
ABBfGN RESPONSE TYPE FOR
ZONE 14
IOIPI
Pm1
VIP1
10141
IOIFI
IOH
rVI
IOIl
COMMENTS: Enter 2 digits. go-09
in each field (useoneof the re-
sponse types below).
g&Ass@ for unusedmnea
01-ENTRYIEXfT, Burghry
021Not Used
03-PERIMETER, Burglary
04=lNTERICR,FCLUIWER,
Burglary
OS-TROUBLE BY DAY/ALARM BY
NIGHT. Burglary
06-24 HOUR SILENT
07-24 HOUR AUDIBLE
06924 HOUR AUXfLlARY
O&FIRE
ABSIQN RESPONSETYPES FOR
KEYPAD PANfCS
1[O][O]Zeroa to be entered
2 [Opll3h# Panic (displays 96)
3 (01[6]‘81 Panic (displays 99)
COMMENTS: Enter response
types (see address ‘02 for types)
in field bcations 2 and 3 onfy (enter
00 in field 1)
BENBORTYPE USED FOR
ZONES 1=6
12345676
rwmlHllIll[lPll
COMMENTS: Enter a zero for each
N.O. sensor zone or 1for each
N.C. sensor zone. The entry for
zone 1onfy &ii to that zone
whenft bnotusedasanend=Of-
Iii resistor supervised zone.
ENTRY DELAY
IOlPl
COMMENTS: Mines the time
period between afault wrring in
a zone to whit Entry delay has
heen assignedandthe time when
the ahrrn will samd (UL Household
Burglaty usagepermits a maximum
of 45 seawads).Enter00-15. Muttipfy
by 15 secondsto determine time
delay (O-225 seconds availa&).
EXITDELAY
Ifm31
COMMENTS: Definesthe time delay
period after the system armingcode
Iskeyed when zone to whichthis
delay has been assignedwill arm
(UL 1023Household Burglary usage
permits a maximumof 60 seconds).
Is also the exk delay time allocated
to the lnterbr zones. Enter 00-15.
Multiply by 15secondsto determine
time delay (o-225seconds available).
ALARM SOUNDERDURATION
m41
COMMENTS: Definesthe lengthof
time an externalor the console’s
alarm sounder will sound for all
audit&r alarms. Enter01-16. Multiply
by 2 minutesto determine sounder
duration (UL 1023Household
burglary usage requires a minimum
of 4 minutes).
ZONE 6 RESPONSETlME
PI
COMMENTS:Determine response
time for zone 6. Enter0 or 1
O-slow @56-500msec).
l-fast (16-15 msec).
DfSABLE flRE TfME-OUT
PI
COMMEm Diibs the sounder
timeout feature for any zone
designated as afire zone so that fire
sounding continues untilthe system
is reset. Enter0 (time-out)or 1 (no
time*@. 1 is requiredfor usagein
awordance with UL-985, Househofd
fire.
DISA8LEDURESS REPORTING
IN ADEMCD EXPRESS FORMATS
PI
COMMENTS:Onlyappliie if
AdemcoExpressFormatisselected.
Enter 1 to disableduress raporting
or Oto enable duress reporting.
TEST REPORTBITERVAL
121
COMMENTS: Determinestime
period between test reports. Enter0
(no rep&), or 1 (12hours),.2 (24
hours)or 3 (166 hours). Programfor
a maximum of 34hoursfor ULinstal-
k&ions.Must bs used in conjunction
with Data Fold l68 (bcatbn 5).
QUICK ARM
Ill
COMMENTS:Enables arming of the
burglary system in any mode without
use of a SecurityCode (just [#I key
depressionfolbwed by the command
AWAY, STAY, INSTANTor MAXI-
‘30
‘31
‘32
MUM). When armed AWAY,
reports cbsing as User 17. Enter g
(disabled) or 1 (enabled).
;TdS)UCHTONEOR ROTARY DIAL Iq
.~’ / COMMENTS: Permits selection of
the type of dialing to be used. Enter
1 for TouchTone. 0 for Rotary
Cautton:Do natselect a dialing
method that is not legally permitted
by the telephone company for the
particular subscriber (if selecting
TouchTone’, make sure the
s&scriber has requested and is
paying for TouchTone service).
Note: Whether or not TouchTone
dialing for call placement is
permitted, communication by the
use of DTMF signalling (Adem=
Express) will still take place.
PABX ACCESS CODE
[I[1 111 [II [III
COMMENTS: ff not required, enter
nothing and proceed to next
address: otherwise, enter prefix
needed to obtain an outside Telco
line. This field may be used atterna-
tively to enter a prefi that can sup
press the Tebo’s call wafting feature
from interfering with outgoing trans-
missions. Thii p&ii is only useful if
the Telco option to he able to sup-
press call wafting has been obtained
by your customer. The prefix to he
used is 1170 if pulse dialing is being
used or ‘70 if TouchTone dialing is
being used. /*\ ‘1
Enter up to 4 digits. Each digit re-
quires a a-digit entry so as to allow
entry of hexadecimal digits (B-F).
Use the folbwing chart to determine
the entry for each digit. Only enter
digits required. Do not fill unused
spaces. Erase the field by entering
g.*‘ENTER No. ENTER
0 00 6 06
1 ii 9
3 03 A (DO%JSE)
B 11
4 04 C 12
05
t 06 Lx* 1’:
7 07 Fall 15
SUBSCRIBER ACCT. NO.
ImI1~5lImlm5l
COMMENTS: Enter 3 or 4 digits.
Each dgit requires a 2digit entry
so as to allow entry of hexadecimal
digii (B-F). ff a 3digft number
is to be used, only enter data in the
first 6 locatbns. leaving the last two
unfilled. Use the chart in address
‘31 to determine the entry for each
digit. Erase thefield by entering 32.

33
34
-36
06
040
PRIMARY PHONE Na
[ItEHIIItliHnlInH1
COMMENTS:Enter up to 12digits,
Q-9.Do not fill unused spaces.
Erasathe fiild by entering W.
NotorBadc-up reporting (8 calls are
madeto the secondaryphone
number if no adtnowledgment is
recaived after 8 attempts to the
primary number)is automatic only if
there is a secondary phonenumber.
SECONDARY PHONE No.
~l[IPI~I[lt~l(I~PPl
COMMENTS: Enter up to 12digits,
9-Q.Do notfill unused spaces.
Erasethe fiikl by entering 34’.
Note: Per UL std. 1635,onty 10
(total) reportingattempts can be
made.Therefore,the saaxtdary
phoneNo.cannotbeusedin aUL
1995 installation
CENTRAL STATION DOWNLOAD
PHONE No.
[I[l[PItI[PHlIlIPPl
COMMENTS: Only applicable if
downloading will be utiliied. Enter
upto 12 digits,O-9.Do not fill
unused spaces. Erasethe field by
enteringrS*.
CENTRAL STATlON ID No.
ml ml ml UIFI
ml ml PIR [lIPI
COMMENTS:Only apptiie if
downloading will ba utiliied.
Enter all 8 hexadecimaldigit (O-9,
A-F)
oo-0 044 08-8 12-C
01-l zz 09-Q 13-O
sz 10-A 14-E
07-7 1118 15-F
PROGRAM TAMPER CODE
Pm
COMMENTS: See table for ‘65.
l 41
044
044
DISAELEUSAGEDFEND-DF-
LINE RESlSlDR SUPERVWON
ON ZONfE1.
PI
COMMENTS:Enter 1 to change
zone 1to N.C.or N.O. bop that
does not require an 1.EMer0 to
retain EOLRsupanrisiin of zone 1.
RING DETECTlON COUNT
PIP1
COMMENTS:Only applicableif
central station initiateddownloading
will be used.Enter 00 to die
ring detection. Enter0144 for ring
axmts of l-14. Determinesafter
how many ringsthe systemwill an-
swerthe inaming call. Enter15 to
select modethat gets aroundtele-
phone answeringmachinescon-
nectedto the same phone lines. In
the fattermoda,the system,upon
hearingona ringfollowed bynothing,
will not answerbut will‘readyttseff
to pick upthe next incomingcall re-
ceivad withinthe next 30 seconds
RING DElECIlON COUNT
I0lP1
COMMENTS:Only appfii if
central station initiateddownloading
will be used.Enter 00 to die
ring detection.Enter 01-14 for ring
arunts of l-14. Detenines after
how many ringsthe systemwill an-
swer the incomingcall. Enter15 to
select modethat gets aroundtele-
phone answeringmachinescan-
nactadto the same phone lines. In
the latter mode,the system,upon
hearing ana ringfollowed bynothing.
will not answerbut will ready ftsellto
pick up the next inmming call re-
ceived withinthe naxt 30 seconds
on the first ring (the downloader
calling again).
l 46
946
-49
064
PRIMARY TRANSMISSION
FORMAT
l$~~Em- Permits selaction be
-
tween Adam& Low Speed fOmW,
Padiintcs. or Ademco Expressfor-
mat Enter 0 (Ademaa Low Speed),
1 Radionics). or 2 (Ademco Express)
Nets: If Ademco Express repomng
is selected, the reports desired must
be selected in Addresses l 85
through ‘98 (any non-zero code may
be used).
SECOELILLRYTRANSMISSION
FORMAT
PI
COMMENTS: Same options as
Address ‘46. Enter 0 (Ademco Low
Speed), 1 (Radionics), or 2 (Ademco
Express).
SINGLE MESSAGE XMISSION
WITH CHECKSUM
VERIFICATION
101
COMMENTS: When selectad. will
send a verificatiin digit wtththe
messageto validate the massage at
the receiverwithout having to send
two message rounds. Enter 0 (NO)
or 1 (YES).
Note: Setaction applies to both
primary and secondary phone
numbers.
4+2 FORMAT SELECTION
PI
COMMENTS: Enter 1. if 62 re-
porting is desired. entar 0 if 3cl/
4+1 reporting is to be usad.
9

The fofbwbg reports (Address ‘55~‘80) may be designated to rqort efther In Standard or Expanded format. In all cases. the Standard
massafM rworts to tha oantralstation a subscrib ID numbsr and a rworf fe.a.. alarm lsee Address ‘551. trouble. restore. orwVckxte~
.---..--.--- --,._.-- ~~.
code. The Expandad rnaswge reports a subscriber fD number, the r&ori’&, followed by 8 second line where the r&k code/’
f---J
rspeatad thras or four times and fs trailed by the mne numbar (or usar ID) relatsd to that repon. When 4+2 format is selected,,.
ssamd llne Istransmfttad.The zons numberor Usar fD is sent as the fastdigit of the report. ,’
3+1/4tl
Bfandatd
SSS(S) A
=W) T
SSS(S) B
SSS(S) E
SSS(S) L
s%(S) 0
SW(S) c
SSS(S) M
SSS(S) x
SSS(S)Ts
SSS(S) R
SSS(S) R
SSSfs) R
SSW) 9
ssw s
3+114+1
Bxpandad
BSS(S) A
AWA) Z
SSS(S) T
ROZ
SSS(S) B
EBB(B) Z
SSS(S) E
E=(E) k
SSS(S) L
uL(L) LB
SSS(S) 0
=w) u
SSS(S) c
=w) u
SSS(S) M
SSS(S) x
SSS(S) Te
SSS(S) R
RRR(R)Z
SSS(S) R
RRWW A,
SSS(S) R
RRR(R) Lg
SSS(S) Pi
RTRTRT( Tjz
SSS(S) RB
F$R&(RB) Z
4t2 Expandd
SBSSAZ
ssss R
ssss Bz
ssss EAc
ssss h
ssss ou
ssss cu
ssss M0
ssss x0
SSSS TeO
ssss Rz
ssss %
SSSS R$
r‘\
., !
Where:
BBSorBBBB-SubscrfberID
A -AlarmCode
0 -zero
Z ~ZoneNurnbef
T -TroublaCbde
B -Bypasscode
E ~ACLossCode(tstDigit)
2: A&+sCf&sCf& (2nd WW
M - Program Tamper Code
‘Zone numbers for:
Duress - 9
p]&[#JPanic-A
[.]a[#jPanic-B
L I Low Battery Code (1st digit)
9 I Low Battery Code (2nd digit) -Open&de
C =CloseCode
U I User Number
Te I Test Code
R - Restore Code (Alarm, AC Loss, Low Battery)
I+ Restore Code (Trouble)
RB- Restore Code (Bypass)
10

‘55 ALARMREPORT
PI
COMMENTS:Enter0 (Standard
Report)or 1 (ExpandedReport).
When Expandedis selected,the
zone number is transmitted inthe
last positionof the 2nd transmission
line (or of the 1sttransmissbn lineif
4+2 Format is used.
Note: Selectionappliis to both
prirxid secondary phone
‘56 RESTORE REPORT
VI
COMMENTS:Enter0 (Standard
Report)or 1 (ExpandedReport).
When Gpanded is selected, the
zone numberis transmitted in the
last positiin of the 2nd transmissbn
fine (ofthe 1sttransmissbn fineif
4.42Format is used)forzone alarms,
bypasses, andtroubles. For AC loss
and bw Battery,the 2nd digit code
selsctad (see ‘87 and 88) appaars
inthat location.
Note Sektion appliestp both
primary and secnndary phone
numbers.
57 BYPASS REPORT
56
PI
COMMENTS: Enter0 (Standard
Report)or 1 (Expanded Report).
Bypassing a zone results in a by-
pass report and in a restore report
when all bypasses are removed.
Fiie zones cannot be bypassed.
When Expanded is selected. the
zone number is transmitted inthe
last position of the 2nd transmission
line (or of the 1Sttransmission line if
4-t2 Format is used).
Note: Selection appliesto troth
primary and secondary phone
numbers.
TROUBLE REPORT
PI
COMMEMS: Enter0 (Standard
Report)or 1 (Expanded Report).
When Expanded is selected, the
zone number is transmitted in the
last positiin of the 2nd lransmissbn
line (orof the 1attransmission line if
4+2 Format is used).
Note: Sabctiin apptiis to both
primary and secondary phone
numbers.
lSQ OPPUCtOSE REPORT
PI
COMMENTS:Enter0 (Standard
Report)or 1 (ExpandedReport).
When Expandedis selected, user ID
(l-6) is transmittedin the last
positiin of the 2nd transmissbn line
(or of the 1sttransmissbn line lf 4+2
Format is used).
Note: Selectionappliesto both
primary and secondaryphone 6s.
PI
COMMENTS:Enter0 (Standard
Report)or 1 (ExpandedReport).
When Expandedis selected, and
addiibnal programmable(excspt for
lest whii hasa 0) axis istrans-
mitted inthe lastpositiin of the 2nd
transmission line (ctfthe 1st trans-
missbn line if 4+2 Format is used).
Note: Selsctiin applies to both
Wmaz;d -=dary phone
ALARMREPORTING
CQDESASBIGNED
[OHO]Zone 1
[OgO]Zone 2
[OHO]Zone 3
[Ol[O]Zone 4
[OHO]Zone 5
[Ol[O]Zone 6
[O)[O]Zone 7
[O][O]Zone 8
COMMENTS:Enter all alarm rs-
porting codes as double digits.
Disable = 00 (nocode reporting).
01-l 86-6 11-B
0212 Of-7 12-c
03-3 08-8 13-D
044 09-9 14-E
05-5 lo-0 16-F
ALARM REPORilNG CODES
ASSIGNED (-7)
[OIO]Duress
[O]IO][3]8[X] Panic
[OgO]p] 8 [W]Panic
COMMEMS: Enterall alti
reportingcodes as doubb diiits
(sameas Addresses ‘66). Dissblsd
II 00 (no code reporting).
‘61 NON-ALARM CODES
[o][O]AC LOSS
[o][O]AC LOSS 2ND DlGfT.
[O][O]TROUBLE
[O][O]TROUBLE RESTORE
K11101BYPASS
i&j BYPASS RESTORE
[O][O]RESTORE CODE FOR
ALARM, AC LOSS, LOW
BATTERY
COMMENTS: Enter all nodesdouble
diilts (see Address ‘65). Died =
60 (no report).
‘ff you have entered a reporting
code for AC Loss. enter code here.
Thii is necessary regardless of the
reportingformat selected (s.g..
Adsmm Express 3+1,4+1). Thii
axle is also transmitted with the
restore code when expanded rs-
porting is used, so it may be de-
sirable to make it the same asthe
AC LOSS report ctxfe.
-8 NON-ALARM CODES
[OIO]OPEN
[O][O]CLOSE
[O][O]LOW BATTERY
[O][O]LOW BATTERY 2nd DffiTr
I’Wl TEST
[O][O]CANCEL CODE”
COMMENTS: Enter all codes as
double diitts (see Address ‘66).
Disable I 00 (no rep&).
‘If you have entered a reporting
code for LOW BATTERY, enter a
codehere.Thiiisrlscawy
regardless d the rsporting format
selected (e.g.,Ademao Express 3+1,
4+1). This code is also transmitted
with the restore axle when ex-
panded reporting is used, so it may
be desirable to make itthe same as
the LOW BATTERY oode.
l * When 4+2 format is used,the 2nd
digit of the event code b ahuays
-0..
Note: fl system is shut down by
using a securfty code while a
burglary afarm is sounding, a cancel
code will be sent (not sent for 24-
hour zcmes).
11

41ZOEC PROGRAMMING FORM
PRODRAMTAMPER -40
DD-Q9;E-F
m
USEEOLRON
VI
ZONE 1
q
l-NoEaRo.K)uI~
(EWIERW
UBTER CODE
aamm
aba
‘48
CHECK!3M VERIFY
1rVa.0.b
4+2 ZONE
FORMATSEUECTlON
1rMmmm
OlklM+l
ALARMREPORT
09QaW:1.t-
RESTOREREPORT
O-ml-w
BYPASSREPORT
00-1-w
TROUBLERE#)Rl
O-lDnw:l.~
OPENICLO6EREPORT
00aadM:l-Expndrd
LOW6Ar;ACLoss
b TESTREPDRl
01stmwel.~
ALARMCODmFOR
6ACHZONE -
MDELAV
xllnmmo-l5l
-m
6uBscRtBER8
OD-oD;s-F =l
PRlMhRVPHONEN~
“rrrrrrrrrrm
SECPHONE# W NON-ALARMCODEB W
(HuOl-1s:
cm-mm
-1
ACLOSSWOG’i
C 0.1O~pQRlWDES) 1.01 A02 JIOI 4004 bo!l&S I-07
O.~(~~I~~D.PIB~~RCSP) cm b09 &cc t12D.(2 0-W F-95
1
12

TESTING THE SYSTEM
After installation is completed. the Security System should be
carefullvtested.
1.
2.
With the System in the disarmed state, check that all zones
are intact. lf NOT READY is displayed, press the [‘I key to
display the faulted zone(s). Restore faulted zone(s) if
necessary, so that READY is displayed. Fault and restore
every sensor indiiidually to assure that it is being monitored
by the system.
Enter the wcurlty code and press the TEST key. The
external sounder (ff used) shoukf sound for 3 seconds and
then turn off and a test report should be transmitted (if
programmed)to the Central Station. lf the badtup hattey is
discharged or missing, the external sounder will not turn on
and a LOW BATTERY report will be transmitted instead of a
TEST report.
A messagewill he sentto the central statbn during the folbwing
test. Notifythe central stationthat a test will be in progress.
Arm the system and fautt one or more zones. Silence alarm
sounder(s) each time by entering the code and pressing
OFF. Check Entry/Exitdelay zones.
Check the keypad-initiated alarms by pressing the Panic
key pairs-[1 and 18)and/or p] and [8& If the system has
been programmed for audible emergency, the console will
emil a bud, steady alarm sound, and AlARM and 99 will be
diiyed for 11 and [a (if p] and [rr) are pressed, 96 will
be displayed). Silencethe atarm hy entering wcurlty code
end pressingOFF.
II the system has been programmed for silent em-ergency.
there will be no audible alarms or displays, but a report will
be sentto the central station.
Notify the central station that all tests are finished, and
verify resultswith them.
NOM:
0
ffthabattarystandbycapackyisexceadedduringanAC
power failwe. tha 4120 will automatically shut itself off so
that lt can retain 6s armed state (OFF, AWAY, STAY,
etc.). When AC power is restored, the 4120 will assume
its armed status prior to the AC power interruption.
I
TO THE INSTALLER
Rag&r mabtenanoa and lnsp&in (at feast annually) by the
instaflerandfrequent tasting by the usar am vital to continuous
satisfsctory operationof any alarm system.
The installer should assume the responsibility of developing
snd offering a regular maintenance program to the user as well
as acquainting the user with the proper operation and
limitations of the alarm system and its component parts.
Recommendations must be included for a specific program of
frequent testing (at least weakly) to insure the system’s proper
operatbn at all times.
SPECIFICATIONS
4120 SECURI’IYCONTROL
1. PhysIcal: 12-Vl’(318 mm) W.
14-12 (388 mm) Ii,
3’ (76 mm) D
2. Ebctrfcal
VOLTAGE INPUT: 16.8VAC(fromplug-in 26VAtransfor-
mer, Adema, No.132fm2). ln Canadian instal-
latbns. No. 1321CN must be used.
RECHARGEABLEBACK-UP BATTERY: 12VDC.4AH
(Gel or starved lead-acid type)
ALARMST)UNfER: x)-13.8V. 2.8 Amp output (360 mA
max.on alarm for a UL instakatiin). I
OUTPUT: Candrive 12Vmotor driven hells (100 mA
each) - AMSECC MSB16Gor ABE1031. Do not
use solenoidoperated hells.
Candriie one 7tI2or two 702 (series connected)
self-contained29-watt sirens. Do not connect two
702s in parallel.
AUXIUARY POWEROUT-PUT:X)&13.8V DC,XI0 mA
max.for non-UL instalfati~. 400 mA max.for UL I
installations.
STANDBYTIME: 4 HRS. withAuxiliary bad d 5oomA’
‘Using 4 AH Battery
3. Communlcatkn:
FORMATS SUPPORTED:
Ademco Bxpresa, ‘10char-acterslsec, DTMF (Touoh-
lone) DataTones, 14M)I2300 Hz ACK, 1400 Hz
KISSOFF.
Ademoo Low Speed, 10 pulseslsec, 1900 Hz Data
Tone, 1400 Hz ACW KISS-OFF.
RADIONICS. 20 pulses/ sec. 1800 Hz Data Tone, 2300
Hz ACKMISSDFF reports O-8,B-F).
Line Seize: Double Pole
Ringer Equivalence: 0.78
FCC Registration No.: AC 398U-68192-AL-E.
4127 REMOTE CONSOLE
1. Physfcal: 6-~(l43mm) W
44lrtQMmm) H
2. Elactrlcal: 7&=(22mm)D
Voltage Input: 12V DC
Current Drain: 20 mA
3. Interface Wlrlng:
RED: 12V DCinput (+) aux pwr
GREEN: Data In
YELLOW: Data Out
BLACK:Ground
5330 REMOTE CONSOLE
1.Phyalcsl: 7-314yf43mm)W
67116’~%tnn)H
1 114’(32nxn)D
2 Ebctrlcal:
Voltage Input: 12V DC
CurrentDrain: 106 mA
3. lntertace Wlrlng:
RED: 12V DC input (+) aux pwr
GREEN: Data In
YELLOW Data Gut
BLACK:Ground
4137 REMOTE CONSOLE
1.physlcsl: 8-X. Ql3mm)W
4314’ (12mm)H,
2. Electrkal: l-lfia (28mm)D
Voltage Input: 12V DC
Current Drain: 60 mA
3. Interface Wlrlng:
RED: 12V DC input (+) aux pwr
BLUE: Not Used
GREEN: Data ln
YELLOW: Data Out
BLACK: Ground
13

ACCESSORIES
No. 122lm
No. 4lWCB
Na 4127
Na 4137
No.8220
BRK PA4OOB
No.7D2
No.740
No.412oPR
N0.w
BRK1400
BRK2400
BRK24OOTH
wotULL&ted
lB.WAC, 26VA Plug-in Tmnsformer.
Contml C&net
Refnoteconsob
Remote Consob
Remote Alpha Consob
Piezodec!rk Alarm Sounder, 9odB outpul (mountsin singlegang box).
Selfmed 26 watt Siren (indoorloutdoor)
Extmmefy bud Piibctrfc Abmt Bounder, 122dB output (indoor/outdoor).
SO-sheetpad of Progmmmlng Forms.
Gmund Btut Modub
2&m bnkation Producb of Comhwtion Detector
2-wire Photoebctric Smoke Detector
2-wire Photoelectric Smoke Deter wfl3YF (57oC)Heat Detector
l In Canadian bstaflatbns, No. 1221CN must he used.

15

FEDERAL -CA?lONS OOMMlSStON (FCC) STATEMENT”
This cw@ment has beentested to FCC requimments mf has been found aoceptahb for use. The FCC requires the folbwing
statement for your idormatbn. n
This equipment genemes and uses ndb frequency l nefgy and if not inataibd and used properly. that is, in strict accordance
with the manutactureh &nstrWbns may cause interferertoeto radio and television reception. h has been tested and found to
comply with the IknItsof Put 15of FCC Rubs, which are designed to provide reasonahb protection against such interference
in a resideniial fnat&tbn. However, there is no guarantee that interference will not oo#1r in a particular installation. lf thii
@quipneti does cause intelferen~e@radii or tebvsbn reoeptbn. whii can be determined by turning the equipment off and
on, the user b encouraged to try to ~)mmctthe bterference by one or more of the folbwing measures:
l ff using an indoor antenna, havea qua&y outdoor antenna installed.
l Reorientthe receivingantenna until interferertoe b reduced or eliminated.
l Move the receiver away from the aontrollcammunkator. A ten-foot separation is recommended.
l Movethe antenna bads away from any wire runs to the controlloommunicator.A ten-foot separation is recommended
l Plug the cont@communicator into a different outlet so that if andthe receiver are on different branch circuits.
ff necessary, the user should consultthe dealer or an experiencedradioAeievisiontechnician for additional suggestions.
The user may find the following booklet prepared hy the Federal Communications Commission helpful:
‘Interference HandhoolC
This bookbf b availahb from the U.S.Govemment PrintingOffice, Washington, DC29402. Stock ND.004-090-00450-7.
The user shall not make any changes or modifiitions to the equipment unless authorized by the Installation Instructions or
User’s Manual. Unauthorizedchangesor modifications could void the user’s authority to operate the equipment.
I
, \
,:
Umltod Warranty
Alarm Device Manufacturing Company,a Division of pittway Corporation, and its divisions, subsidiaries and affiliates
(%eller), 195 EileenWay, Syosset,New York 11791, warrantsits products to he in conformance with its own plans and
specifications and to be free from defects in materiils and workmanship under normal use and service for 18 monthsfrom
the date stamp aontrolon the product or, for products not having an Ademm date stamp, for 12 months from date 01
original purchase unlessthe instalbtbn instrtiions or catakrgsets forth a shorterperiod, in which case the shorter period
shall apply. Seller%obfiiation shall be limited to repairingor replacing, at itsoption, free of charge for materials or bhor.
any part which is proved rot in compfbnce with Seller’sspecifications or provesdefective in materials or workmanship
under normai use and seenrice.Seller shall have no obligationunder this Limited Warrantyor otherwise if the product is
altered or improperly repaired or senrii by anyone otherthan Ademco factory service. For warranty service. return
I product transportation prepaid,to Ademco Factory Service, 199 Eileen Way, Syosset. New York 11791.
THERE ARE NO WARRANTIES. EXPRESS OR IMPLIED,OF MERCHANTABILTTY,OR FITNESS FOR A PARTICULAR
PURPOSE OR OTHERWISE.WHICH EXTEND BEYONDTHE DESCRlPTlON ON THE FACE HEREOF. IN NO CASE
SHALL SELLER BE LfABLE TO ANYONE FOR ANY CONSEOUENTtAL OR INCIDENTALDAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,OR UPON ANYOTHER BASfS OF LIABILDY
WHATSOEVER, EVEN IFTHE LOSSOR DAMAGE Is CAUSED BY THE SELLERS OWN NEGLIGENCE OR FAULT.
Seller does not representthat its product may not be Compromisedor circumvented;that the product will prevent any
personal injury or pmperty loss by burglary, robbery, fiie or otherwise; or that the product will in all cases provide adequate
warning or protectkm. Buyer understandsthat a prop&y instalbd and maintained alarm may onty reduce the risk of a bur-
gbry. robbery or fne without warning,but ft is not insuranceor a guarantee that such will not oozur or that there will he no
personal injury or property loss as a resutt. CONSEQUENTLY.SELLER SHALL HAVE NO LfABlLfTY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAfLED TO GIVE
~WARNING. However. if Setteris held lbbb, whether directly or indirectty,for any bss or damage arising underthii Limiied
Warranty or otherwise, regardless of cause or origii. Selbfs maximum liabilii shall not in any case exceedthe purchase
price of the product, which shall be the oompbte and exdusive remedy against Seller. Thii warranty replaces any previous
warranties and is the only warranty made by Seller on thii product. No increase or alteration, written or verbal. of the
obliiation of thii Limited Warranty is authorized.
~EMCOJ
MARY=& EvwRdG CO.
169 Eileen Way, Syosset, New York 11791
CopyrtgM 8 lSB0 PillWAY CORPORATION
i”\
‘. .’