ADEMCO VIA-30PSE User manual

Ademco Via 30PSE Quick Guide
https://alpha.adt.com/help/30.html[11/8/2018 11:31:58 PM]
Ademco Via 30PSE Quick Guide
For a detailed review of the entire system, please view the Ademco Via 30PSE manual.
« Help Center
Arm &
Disarm the
System
Battery Bypass
Protected
Areas
Date &
Time
Settings
Chimes &
Beeps
Reset Security
Codes
Trouble
Conditions
Volume
Arm and Disarm
Arm:
To arm in STAY mode when you are not leaving the premises, enter your [security code] + [STAY].
To arm in AWAY mode when you are leaving the premises, enter your [security code] + [AWAY].
To arm in MAX when there is no entry delay, enter your [security code] + [MAX].
Disarm:
To disarm, enter your [security code] + [1].
Select

Ademco Via 30PSE Quick Guide
https://alpha.adt.com/help/30.html[11/8/2018 11:31:58 PM]
For more information on this topic please visit the complete Ademco Via 30PSE manual.
Battery
The Ademco Via 30PSE operates on a UB 1270 battery.
Loss of AC power and use of backup battery power is indicated by NO AC.
A low battery condition is indicated by BAT.
For instructions on replacing your battery, please go to the Battery Replacement Page for this
battery.
For more information on this topic please visit the complete Ademco Via 30PSE manual.
Bypass Protected Areas
Bypassing a zone allows you to arm your system with certain protected areas intentionally unarmed or to
access a protected area when the system is armed.
To bypass a zone, enter your [security code] + [BYPASS] + [2 digit zone number].
To unbypass a zone, disarm the system.
For more information on this topic please visit the complete Ademco Via 30PSE manual.
Change Date and Time
To change date and time settings, enter your [security code] + [#] + [6] + [3].
Wait until time/date are displayed, then press [*] to move the cursor ahead and [#] to move back.
Enter the 2-digit hour and minute settings, i.e., [06] and [17] for 6:17.
Press [1] for PM or [2] for AM.
Continue to enter 2-digit year, month, and day settings, i.e., [15], [08], and [23] for August 23, 2015.
To exit, press [*] when the cursor is on the last digit.
Chimes and Beeps
Your system communicates events using chimes and beeps.
The panel chimes twice when a protected door/window is opened.
To silence or enable chimes, scroll until the panel displays [Chimes], then press [OK].
Scroll to toggle [ON] or [OFF], then press [OK].
Press [Status] to exit.
A solid bell feature will appear in the display when Chime is enabled.

Ademco Via 30PSE Quick Guide
https://alpha.adt.com/help/30.html[11/8/2018 11:31:58 PM]
Return to Top
To turn chime mode on and off, enter your [security code] + [CHIME].
When your system is in chime mode, a chime alert will sound three tones whenever a protected
door/window is opened.
For more information on this topic please visit the complete Ademco Via 30PSE manual.
Reset
To clear the display after an alarm event, enter your [security code] + [OFF] sequence twice to clear the
alarm event history.
Security Codes
Your system allows for additional users, however only the Master user can assign user codes to users.
To add a user, enter your [Master code] + [8] + [new user number] + [ 4-digit new user’s code].
To delete a user, enter your [Master code] + [8] + [user number]. Wait approximately three
seconds for the keypad to verify.
Trouble Conditions
Trouble conditions are indicated by the word CHECK and continual beeping from the touchpad. Any key
will silence the beeping. A display of CHECK + zone no. may indicate that a problem requires your
attention. Check the specified zone area, close any open doors or windows and enter your security code
and press [OFF]. If your system includes wireless sensors, the CHECK condition may be caused by some
change in the environment of the protected area.
To silence trouble beeps, press any key or enter your security code and press [OFF].
For a complete list of Trouble Conditions, please refer to the Safewatch and Ademco Systems
Troubleshooting page.
Volume
The volume on the Ademco Via 30PSE is not adjustable.
How can we help?
Search

Ademco Via 30PSE Quick Guide
https://alpha.adt.com/help/30.html[11/8/2018 11:31:58 PM]