ADJ HYDRO WASH X19 User manual

User Manual
HYDRO WASH X19
USA# HYD190
EU# 1237000302
UPC# 818651028232

©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
2
Date Document
Version
Software
Version DMX Channels Notes
06/29/2020 1.0 1.1 16 / 88 / 90 Initial Release
08/13/2020 1.1 NC No Change Updated System menu / error codes
10/08/2020 1.2 NC No Change Updated zoom range value
07/14/2021 1.3 1.2 16 / 26 / 88 / 90
Added 26-ch DMX mode; added Pixel Zones;
updated Features, Safety Guidelines, Fixture
Installation, System Menu, & Technical Specs
08/10/2021 1.4 N./C No Change
Updated Overview, System Menu, WiFly
Control, and Specifications, removed Software
Updates
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this docu-
ment may be available online.
Please check www.adj.com for the latest revision/update of this manual before begin-
ning installation and/or programming.

TABLE OF CONTENTS
3
Introduction 4
Features | Warranty Returns 5
IP Notice 6
Safety Guidelines 7
Overview 10
Torque Settings & IP Tester 11
Torque Screw Locations 12
Fixture Installation 13
Connections 17
DMX Set Up 18
DMX Addressing 19
DMX Channel Modes 20
Color Macro Chart 27
Color Temperature Chart 29
Pixel Zones 30
System Menu 31
WiFly Control 41
Target Modes 43
Dimmer Curve Chart 45
Error Codes 46
Dimensional Drawings 47
Multiple Unit Power Linking | Cleaning 48
Limited Warranty (USA Only) 49
Technical Specifications 50
FCC Statement 51

4
Unpacking: Thank you for purchasing the Hydro Wash X19 by ADJ Products, LLC. Every Hydro Wash
X19 has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your xture for any damage and be sure all accessories necessary to oper-
ate the unit has arrived intact. In the case damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Do not return this unit to your dealer
without rst contacting customer support.
Introduction: The ADJ Hydro Wash X19 is a DMX intelligent, IP rated, high powered, moving head
xture. To optimize the performance of this product, please read these operating instructions carefully
to familiarize yourself with the basic operations of this unit. This product is intended to be used by
professionally trained personnel only and is not suitable for private use.
These instructions contain important safety information regarding the use and maintenance of this
unit. Please keep this manual with the unit, for future reference.
Customer Support: Contact ADJ Service for any product related service and support needs. Also
visit forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit:
http://parts.adj.com (US)
http://www.adjparts.eu (EU)
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [email protected]
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [email protected]
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]
www.adj.eu | [email protected]
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton whenever possible.
INTRODUCTION

• IP65 Outdoor Rated
• Electronic Dimming 0-100%
• DMX-512 Protocol
• IP65, 5-pin XLR, Data Locking In/Out Connections
• 16, 26, 88, & 90 Channel DMX Control Modes
• IP65 Locking Power In/Out Connections
• 6° to 40° Motorized Linear Zoom
• Multiple Unit Power Linking (see section on Multiple Unit Power Linking)
INCLUDED ITEMS:
• IP65 Locking Main Power Cable (x1)
• Omega Brackets (x2)
5
WARRANTY RETURNS
The Hydro Wash X19 carries a 2 year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly writ-
ten on the outside of the return package. A brief description of the problem as well as the R.A. num-
ber must also be written down on a piece of paper included in the shipping carton. If the unit is under
warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number
by contacting our customer support team on our customer support number. All packages returned to
the service department not displaying an R.A. number on the outside of the package will be returned
to the shipper.
FEATURES

IP NOTICE
6
IP65 RATED
An IP rated lighting xture is one, which is commonly installed in outdoor environments and has
been designed with an enclosure that eectively protects the ingress (entry) of external foreign ob-
jects such as dust and water. The International Protection (IP) rating system is commonly expressed
as “IP” (Ingress Protection) followed by two numbers (i.e. IP65) where the numbers dene the degree
of protection. The rst digit (Foreign Bodies Protection) indicates the extent of protection against
particles entering the xture and the second digit (Water Protection) indicates the extent of protec-
tion against water entering the xture. An IP65 rated lighting xture is one, which has been designed
and tested to protect against the ingress of dust (6) and low-pressure water jets from any direction
(5).
MARINE / COASTAL ENVIRONMENT INSTALLATIONS
NOT suitable for marine and/or coastal environment installations. Installing this
xture in a marine and/or coastal environment may cause corrosion and/ or exces-
sive wear to the interior and/or exterior components of the xture. Damages and/or
performance issues resulting from installation in a marine and/or coastal environ-
ment will void the manufacturer’s warranty and will NOT be subject to any warranty
claims and/or repairs.

7
SAFETY GUIDELINES
For Your Own Personal Safety, Please Read and Understand This Manual Completely Before
You Attempt To Install Or Operate This Unit!
• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY.
DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE
DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE
MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS
AND/OR REPAIRS.
• DO NOT PLUG THE FIXTURE INTO A DIMMER PACK!
• NEVER OPEN THIS FIXTURE WHILE IN USE!
• UNPLUG POWER BEFORE SERVICING FIXTURE!
• NEVER TOUCH THE FIXTURE DURING OPERATION AS IT MAY BE HOT!
• KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
• ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A
DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER
CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.
• IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE CHANGES, SUCH
AS RELOCATION FROM AN OUTDOOR COLD TO AN INDOOR WARM ENVIRONMENT, DO
NOT POWER THE FIXTURE ON IMMEDIATELY. INTERNAL CONDENSATION AS A RESULT
OF ENVIROMENTAL TEMPERATURE CHANGE CAN CAUSE INTERNAL FIXTURE DAMAGE.
LEAVE THE FIXTURE POWERED OFF UNTIL IT HAS REACHED ROOM TEMPERATURE
BEFORE POWERING ON.
• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY INDUCE
BLINDNESS! SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
• Be sure that the power outlet matches the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover fro any reason. There are no user serviceable parts inside.
• Never operate this unit with the cover removed.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 7.9”
(20cm) between this device and a wall.
• Do not attempt to operate this unit if it has been damaged in any way.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point at which they exit from the appliance.
• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the
Cleaning section of this manual for details.
• Heat - This fixture should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture shold be serviced by qualified service personnel when the appliance does not appear to
operate normally or exhibits a marked change in performance.

8
SAFETY GUIDELINES
To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual.
ADJ Products, LLC is not responsible for injury and/or damages resulting from the misuse of this fixture
due to the disregard of the information printed in this manual. Only qualified and/or certified personnel
should perform installation of this fixture, and only the original rigging parts included with this fixture
should be used for installation. Any modifications to the fixture and/or the included mounting hardware
will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.
PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR
MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS
TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND
ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH
A DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO
PREVENT WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT
IF THE FIXTURE IS EXPOSED TO ENVIRONMENTAL TEMPERATURE CHANGES,
SUCH AS RELOCATION FROM AN OUTDOOR COLD TO AN INDOOR WARM
ENVIRONMENT, DO NOT POWER THE FIXTURE ON IMMEDIATELY. INTERNAL
CONDENSATION AS A RESULT OF ENVIRONMENTAL TEMPERATURE CHANGE
CAN CAUSE INTERNAL FIXTURE DAMAGE. LEAVE THE FIXTURE POWERED OFF
UNTIL IT HAS REACHED ROOM TEMPERATURE BEFORE POWERING ON.
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

9
SAFETY GUIDELINES
DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow approximately
15 minutes for the fixture to cool down before servicing.
DO NOT shake fixture, and avoid brute force when installing and/or operating fixture.
DO NOT operate fixture if the power cord has become frayed, crimped, damaged and/or if any of the
power cord connectors are damaged and do not insert into the fixture securely with ease.
NEVER force a power cord connector into the fixture. If the power cord or any of its connectors are
damaged, replace it immediately with a new one of the same power rating.
DO NOT block any air ventilation slots; these must remain clean and never blocked. Allow approx. 7.9”
(20cm) between fixture and other devices or a wall for proper cooling.
When installing fixture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, and always attach an appropriately rated safety cable.
ALWAYS disconnect fixture from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end; never pull out the plug by tugging
the wire portion of the cord.
During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fix-
ture. This is a normal process and is caused by excess paint in the interior of the casing burning off
from the heat associated with the LED and will decrease gradually over time.
Consistent operational breaks will ensure fixture will function properly for many years.
ONLY use the original packaging and materials to transport the fixture in for service.

10
1. MENU Button
2. ENTER Button
3. LCD Menu Control Display
4. DOWN Button
5. UP Button
6. RJ45 Port
7. IP65, 5-Pin XLR, Data Locking In/Out
8. Gore Valve
9. Fuse
10.IP65 Locking Power In/Out
OVERVIEW

TORQUE SETTINGS FOR SCREWS:
ALL SCREWS MUST BE TIGHTENED WITH A TORQUE DRIVER. All screws are Allen Head
screws. Please see below for screw locations, screw quantity and torque settings. The number listed
in the “#” column corresponds to the location on the xture. See the xture diagram and number on
the next page for SCREW LOCATION depictions.
# Screw Locations Screw Torque Settings
1 Heat Sink to Head Front Cover (x8) 7.5-10.0 In-Lb
2 Sealed Back Cover to Head Back Cover (x4) 7.5-10.0 In-Lb
3 Yoke Arm Cover to Yoke Frame (8 x Each Side = 16 Total) 7.5-10.0 In-Lb
4 Access Cover to Yoke Frame (x4) 7.5-10.0 In-Lb
5 2nd Access Cover to Yoke Frame (x8) 7.5-10.0 In-Lb
6 Power & Data Connector to Base Casting (x10) 6.0-8.5 In-Lb
7 Handle to Base Casting (2 x Each Side = 4 Total) Fasten by Air Screwdriver
8 Base Bottom Cover to Base Casting (x12) 7.5-10.0 In-Lb
9 Quick Lock Plate to Base Bottom Cover (x16) 7.5-10.0 In-Lb
10 Fixture Feet to Base Bottom (x4) 6.0-8.5 In-Lb
11
TORQUE SETTINGS & IP TESTER
TORQUE DRIVERS (Recommended):
UTICA TS-30 (Shown)
ALTERNATIVE DRIVERS:
Proto J6107A
Wiha 28887
CAUTION! DO NOT OVER TORQUE SCREWS AS THIS CAN CAUSE LEAKAGE ISSUES! TO
CONFIRM THE IP65 INTEGRITY AFTER A LAMP REPLACEMENT, TEST THE FIXTURE USING
THE IP TESTER.

12
TORQUE SCREW LOCATIONS

FLAMMABLE MATERIAL WARNING
Keep fixture at least 0.7 feet (0.2m) away from any flammable materials, decora-
tions, pyrotechnics, etc.
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
Fixture MUST be installed following all local, national, and country commercial electrical and con-
struction codes and regulations. Before rigging/mounting the fixture to any metal truss/structure or
placing the fixture on any surface, a professional equipment installer MUST be consulted to deter-
mine if the metal truss/structure or surface is properly certified to safely hold the combined weight
of the fixture, clamps, cables, and accessories. Overhead fixture installation must always be secured
with a secondary safety attachment, such as an appropriately rated safety cable that meets all local,
national, and country codes and regulations.
Fixture maximum ambient operating temperature is 104°F. (40°C). Do not use this fixture outside this
temperature range.
Fixture should be installed in areas outside walking paths, seating areas, or areas wHere unauthor-
ized personnel might reach the fixture by hand.
13
FIXTURE INSTALLATION
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or installa-
tions.
MINIMIM ALLOWABLE DISTANCE TO OBJECTS/SURFACES IS 1.6 FEET (0.5
METERS)
EXTERNAL SURFACE MAY REACH TEMPERATURES OF UP TO 167°F (75°C)

14
Screw one clamp via an M12 screw and nut into the Omega Bracket. Insert the quick-lock fasteners
of the Omega Bracket into the respective holes of the fixture base plate. NOTE: The clamp must be
attached to the Omega Bracket before attaching the bracket to the fixture. Tighten the quick-
lock fasteners fully clockwise. Pull the safety-cable through the openings located on the bottom of
the unit and over the trussing system or a safe fixation spot. Insert the end in the carabine and tight-
en the safety screw.
NEVER stand directly below the fixture when rigging, removing, or servicing.
Always allow approximately 60 minutes for the fixture to cool down before servicing.
FIXTURE INSTALLATION

15
The trussing or area of installation must be able to support at least 10 times the weight without any
deformation. The unit must be secured with a secondary safety attachment, such as an appropri-
ately rated safety cable. Never stand directly below the unit when mounting, removing, or servicing
the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installa-
tion material being used, and periodic safety inspection of all installation material and the unit. If you
lack these qualifications, do not attempt the installation yourself.
The installation should be checked by a skilled person once a year.
The Hydro Wash X19 is fully operational in three different mounting positions: hanging upside-down,
mounted sideways on trussing, or set on a flat level surface. Always use and install a safety cable as
a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Never use
the carrying handles to secure the secondary attachment.
FIXTURE INSTALLATION
SIDE MOUNTING
TO MAINTAIN IP65 RATING INTEGRITY,
FIXTURE MUST BE INSTALLED WITH
CABLES FACING THE GROUND AT ALL
TIMES. WATER MUST EASILY RUN OFF
AND NOT COLLECT AROUND CABLE
CONNECTIONS.
SAFETY CABLE
ALWAYS ATTACH A SAFETY CABLE
WHENEVER INSTALLING THIS FIXTURE
IN A SUSPENDED ENVIRONMENT TO
ENSURE THE FIXTURE WILL NOT DROP IF
THE CLAMP FAILS.

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS:
External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers, which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting fixtures, can cause severe internal damage including burning to optics, dichroic color filters,
glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring,
discharge lamps, and LEDs.
This issue is not specific to ADJ lighting fixtures, and is common with lighting fixtures from all manu-
facturers. Although there is no true way to fully prevent this issue from happening, the guidelines
below can minimize the risk of potential damage if followed. Contact ADJ Service for more details.
• DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.
• DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS
ANOTHER.
16
FIXTURE INSTALLATION

17
CONNECTIONS
ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A DIELECTRIC
GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT WATER CORROSION
AND/OR ELECTRICAL SHORT CIRCUIT.
TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE
FIXTURE, ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED.

18
DMX SET UP
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be
linked together and operate from a single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible
when using several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Hydro Wash X19 can be con-
trolled via DMX-512 protocol. Your unit and your DMX controller require a 5-pin XLR connector for
data input and data output. We recommend IP65 rated DMX cables to secure the IP65 connections,
such as our Accu Cable STR Series Data Cables. If you are making your own cables, be sure to
use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting
stores). Your cables should be made with an IP65 rated male 5-pin XLR type connector on one end
of the cable and an IP65 rated female 5-pin XLR type connector on the other. Also remember that
DMX cable must be daisy chained and cannot be split.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-
minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE
FIXTURE, ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED, AND ONLY IP65
RATED POWER AND DATA CABLES MUST BE USED.

19
DMX ADDRESSING
DMX ADDRESSING
All fixtures should be given a DMX starting address when using a DMX controller, so the correct fix-
ture responds to the correct control signal. This digital starting address is the channel number from
which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The
assignment of this starting DMX address is achieved by setting the correct DMX address on the digi-
tal control display on the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different addresses
for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to
react in the same way. In other words, changing the settings of one channel will affect all the fixtures
simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the channel num-
ber you have set, based on the quantity of DMX channels of each fixture. That means changing the
settings of one channel will only affect the selected fixture.
For example, when operatin this device in 16 Channel Mode, you should set the starting DMX
address of the first unit to 1, the second unit to 17 (1 + 16), the third unit to 33 (1 + 16 + 16), and so
on. See the chart below for more details.
Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address
16 Channels 1 17 33 49
26 Channels 1 27 53 79
88 Channels 1 89 177 265
90 Channels 1 91 181 271

20
DMX CHANNEL MODES
CHANNEL VALUES FUNCTION
16-CH 26-CH 88-CH 90-CH
1 1 1 1 000 - 255 Pan Movement
2 2 2 2 000 - 255 Pan Fine
3 3 3 3 000 - 255 Tilt Movement
4 4 4 4 000 - 255 Tilt Fine
5 5
Colors
000 - 002 Open
003 - 004 Color 1
005 - 006 Color 2
007 - 008 Color 3
009 - 010 Color 4
011 - 012 Color 5
013 - 014 Color 6
015 - 016 Color 7
017 - 018 Color 8
019 - 021 Color 9
022 - 023 Color 10
024 - 025 Color 11
026 - 027 Color 12
028 - 029 Color 13
030 - 031 Color 14
032 - 033 Color 15
034 - 035 Color 16
036 - 037 Color 17
038 - 039 Color 18
040 - 042 Color 19
043 - 044 Color 20
045 - 046 Color 21
047 - 048 Color 22
049 - 050 Color 23
051 - 052 Color 24
CONTINUED ON NEXT PAGE