ADJ FLASH KLING BATTEN User manual

User Instructions
4/15
FLASH KLING BATTEN
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: [phone] / Fax: [phone]
Web: www.adj.com / E-mail: [email protected]
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.adj.com
Tel: [phone] / Fax: [phone]

©2015 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indi-
rect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you! ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 10
Flash Kling Batten Specifications
Model: Flash Kling Batten
SPECIFICATIONS:
LEDs: 160 x 0.164W 3-in-1 LEDs
Working Position: Any safe working position
Voltage: 100V-240V, 50/60Hz
Power Draw: 54W (Full On)
Units Linked Together: 50 Units Max.
Power Cord Daisy Chain:12 Units Max.
Beam Angle: 120 Degrees
Weight: 7.27 lbs./ 3.3 Kgs.
Dimensions: 39.25” (L) x 4” (W) x 5.5” (H)
1000 (L) x 104 (W) x 140 (H) mm
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.

ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 2
Flash Kling Batten Introduction
Unpacking: Thank you for purchasing the Flash Kling Batten by ADJ
Products, LLC. Every Flash Kling Batten has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during ship-
ping. If the carton appears to be damaged, carefully inspect your x-
ture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without rst
contacting customer support.
Introduction: The Flash Kling Batten is a LED pixel panel for low
resolution, video displays. This LED panel is controlled via Kling-Net
or Art-Net. Recommended control solutions; Arkaos Media Master
Express, Media Master Pro, and LED Master software’s (sold sepa-
rately). Dynamic effects can be played on it, which makes it a great
system for night clubs.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial operation.
You may also visit us on the web at www.adj.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 9
Flash Kling Batten Notes

ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 3
• CAT 5 Straight Network Cable included.
• Kling-Net and Art-Net Compatible (Recommended control solu-
tions; Arkaos Media Master Express, Media Master Pro, and LED
Master software’s (sold separately).
• 160 x 0.164W SMD RGB LED’s
Flash Kling Batten Warranty Registration
The Flash Kling Batten carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ customer sup-
port for a R.A. number.
Flash Kling Batten Features
To optimize the performance of this product, please read these operat-
ing instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
Flash Kling Batten General Instructions
DMX WORKSHOP™ (alternative software option to congure network
settings)
DMX-Workshop™ is a fully featured network management, analy-
sis, conguration and diagnostics tool for Art-Net networks. It can
be used to congure the Ethernet network settings on this xture
remotely such as the IP Address, Subnet Mask, and the DMX Uni-
verse. This software application is Windows XP™ and Windows 7™
compatible and is free of charge and available via download. (See link
below)
http://artisticlicence.com/index.php?mode=products&sub=overview&
action=&product_id=351
Flash Kling Batten DMX Workshop™
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 8
Flash Kling Batten Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war-
ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 90 Day
Limited Warranty)
•ADJDMXControllers=2Year(730Days)LimitedWarranty(excluding faders and tact switches)

Flash Kling Batten Safety Precautions
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 4
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 7 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
ding amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 7
Flash Kling Batten Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Flash Kling Batten Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
No light output from the unit;
1. Be sure the LED indicator on the back of the unit is on and in a
solid state.
Unit is not receiving data;
1. Check the LED indictator (same LED as the Power indicator). If the
LED is flashing, you’re a receiving data. When moving your mouse
arrow around in the grid, the LED will flash if you are receiving
data.
2. Be sure you are using a CAT 5 Straight Network cable.
If problems are not resolved; Contact ADJ for service.
1-800-322-6337
Flash Kling Batten Fuse Replacement
Locate the fuse holder at the end of the base opposite end of the
eithernet connection. Using a phillips head screwdriver, remove the
fuse holder. Remove the used fuse and replace with a matching
fuse. Insert the fuse holder and fuse into the unit and secure the fuse
holder.

ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 6
Flash Kling Batten Connections
When connecting you must use a CAT 5 Straight Network cable. When connecting you must use a CAT 5 Straight Network cable.
Installation method 1:
Note: Do not daisy-chain more than 50pcs LED panels from the computer,and use an Ethernet Switch if more than 50pcs LEDlights are being controlled.
Note:1.The Ethernet Switch must be Gigabit Switch.
2. Do not daisy-chain more than 50pcs LED panels from a single network port of the Ethernet Switch.
3. Maximum 2 output network ports of the Ethernet Switch can be used.So the system can control 100pcs panels maximum.
Installation method 2:
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 5
Flash Kling Batten Operation
Control Using Kling-net or Art-Net:
1. Install one of the recommended operating softwares onto your
computer. Recommended softwares; Arkaos Media Master
Express, Media Master Pro, or LED Master (Sold Separately).
2. Connect the panels via CAT 5 Straight Network cable. When
creating your own custom cable, use RJ45 Straight Network
cable.
3. Map the fixtures using KlingNetMapper or Art-Net Mapper.
4. Control the fixtures using ArKaos or Art-Net software. Please refer
to the media playback software user manual for further instruc-
tions.
Note: ArKaos Kling-Net requires a gigabit (1000 mbps) Ethernet card
and network router for a smoother operation.
Connecting to Power and Data:
When connecting to power, the LED indicator on the bottom of the
unit should glow a solid red if the unit is receiving power.
When the unit is receiving a data signal, the LED indicator will flash
yellow.
Note: The LED indicator may only flash when pressing the mouse and
moving the indicator arrow around in the grid.
Flash Kling Batten Daisy-Chaining Units
Do not daisy-chain more than 50 Panels when connecting directly to
a computer. To daisy-chain more than 50 Panels you must use a Eth-
ernet Switch. When using a Ethernet Switch, do not daisy-chain more
than 50 Panels from a single network port of the Ethernet Switch. A
maximum 2 output network ports of the Ethernet Switch can be used.
So the system can control 100 Panels maximum, no more. See the
directions under the connection diagrams on page 6.
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 12 xtures maximum After the maximum xtures
has been reached you will need to use a new power outlet. They
must be the same xtures. DO NOT mix xtures.
Flash Kling Batten Daisy-Chaining Units