ADJ Mega Tri 60 User manual

User Instructions
Mega Tri 60 Introduction
©American DJ®- www.Americandj.com - Mega Tri 60 User Manual Page 2
9/12
Unpacking: Thank you for purchasing the Mega Tri 60 by American
DJ®. Every Mega Tri 60 has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are miss-
ing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without rst contact-
ing customer support.
Introduction: The American DJ® Mega Tri 60 is part of a continuing
pursuit to create high quality intelligent lighting. The Mega Tri 60 is a
professional indoor, DMX intelligent, high powered LED bar fixture. This
xture can be used in a stand alone mode or connected in a Master/
Slave conguration. This wash has six operating modes: Sound Active
mode, Static Color mode, Program mode, Auto Run mode, RGB mode,
and DMX control mode. To optimize the performance of this product,
please read these operating instructions carefully to familiarize yourself
with the basic operations of this unit. These instructions contain impor-
tant safety information regarding the use and maintenance of this unit.
Please keep this manual with the unit, for future reference.
Customer Support: American DJ provides a customer support line, to
provide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us
on the web at www.American DJ.com for any comments or sugges-
tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
American DJ.
PLEASE recycle the shipping carton when ever possible.

Mega Tri 60 Safety Precautions
©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 4©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 3
• Multi-Colors
• Six Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3-Pin DMX Connection
• Six DMX Modes: 3 Channel Mode, 5 Channel Mode, 6 Channel
Mode, 8 Channel Mode, 11 Channel Mode, and 29 Channel Mode.
• ADJ LED RC compatiable (Not Included)
• Power Cord Daisy Chain (See page 22)
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 22 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Mega Tri 60 Warranty Registration
Mega Tri 60 Features
The Mega Tri 60 carries a 3 year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack-
ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
The unit should be mounted using a mounting clamp (not provided),
afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
Mega Tri 60 Installation

Power Supply: The American DJ Mega Tri 60 contains a automatic
voltage switch, which will auto sense the voltage when it is plugged
into the power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Mega Tri 60 can be controlled via DMX-512 protocol. The Mega
Tri 60 has 6 DMX channel modes, please see page 9 for the different
modes. The DMX address is set on the back panel of the Mega Tri 60.
Your unit and your DMX controller require a standard 3-pin XLR connec-
tor for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained
and cannot be split.
Notice: Be sure to follow gures two and three when making your own
©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 5
Mega Tri 60 Set Up
©American DJ®- www.Americandj.com - Mega Tri 60 User Manual Page 6
Figure 1
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Mega Tri 60 Set Up
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground 1 Ground
XLR Male Socket
XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion

©American DJ®- www.Americandj.com - Mega Tri 60 User Manual Page 8
Mega Tri 60 Operating Instructions Mega Tri 60 Operating Instructions
©American DJ®- www.Americandj.com - Mega Tri 60 User Manual Page 7
Operating Modes:
The Mega Tri 60 has six operating modes:
• Sound Active mode - The unit will react to sound, chasing through the
built in programs.
• Static Color Mode - There are 7 colors to choose from.
• Program Mode - Choose from 1 of 22 built-in programs.
• Auto Mode - The unit will auotmatically cycle through all the programs.
• RGB Mode - Choose one of the three colors to remain static or
adjust the intensity of each color to make your desired color.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the American DJ® Show Designer™.
Sound Active Mode:
In this mode the Mega Tri 60 will react to sound, and chase through the
different colors.
1. Plug the fixture in and press the MODE button until “SU.XX” is dis-
played. “XX” represents the sound sensitivity level (0-31) currently
displayed, 0 being no sound sensitivity, and 31 being the highest
sensitivity. Use the UP and DOWN buttons to adjust the sound sen-
sitivity.
2. The fixture will now change via sound.
3. To activate flash (strobe) press the SET UP button so that “FS.XX” is
displayed. “XX” is the current flash rate that is displayed (00-99),
“FS.00” (flash off) to “FS.99” (fastest flash). Use the UP or DOWN
buttons to adjust the flash rate.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CO-X” is dis-
played.
2. There are 7 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP but-
ton to enter the Flash (strobe) mode.
3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).
Program Mode:
1. Plug the fixture in and press the MODE button until “Pr.XX” is dis-
played.
2. There are 22 programs to choose from. Select your desired program
by pressing the UP and DOWN buttons. After you have selected
your desired program you can adjust the program speed by pressing
the SET UP button so that “SP.XX” is displayed. “XX” represents a
number between 01-99, 01 being the slowest speed, 99 being the
fastest. Use the UP or DOWN buttons to adjust the program speed.
3. Press the SET UP button again, and “Fd.XX” will be displayed, this is
fade speed adjustment. “XX” represents a number between 00-99,
00 is off, 01 the fastest speed, and 99 the slowest speed. Use the UP
or DOWN buttons to adjust the fade speed.
4. Press the SET UP button again, and “FS.XX” will be displayed, this is
the flash (strobe) function. “XX” represents a number between 00-99,
“FS.00” (flash off) to “FS.99” (fastest flash). Use the UP or DOWN
buttons to adjust the flash speed.
NOTE: When eiither programs 21 and 22 are being used, there is an
color option after the flash function. When SET UP is pressed after the
flash function, “1.XXX” will be displayed. This is the setting for the base
color in these programs. Press the UP or DOWN buttons to change and
find your desired base color. After setting the base color press the SET
UP button again, and “2.XXX” will be displayed. This is the setting for the
moving color. Press the UP or DOWN buttons to change and find your
desired moving color.
Auto Run Mode:
In Auto Run mode, color fade can be activated and the fade speed
adjusted. You can also activate strobing and adjust the strobe rate.
1. Plug the fixture in and press the MODE button until either “AUTO” is
displayed.
2. When “AUTO” is displayed press the SET UP button to adjust the
fade speed, flash (strobe) speed, and program cycles.
• Fd.XX = This is fade speed adjustment, Use the UP or DOWN but-
tons to adjust the speed between “Fd.01” (fastest) and “Fd.01”
(slowest). When “Fd.00” is displayed, the fade is off.
• FS.XX = This is flash (strobe) adjustment, Use the UP or DOWN but-
tons to adjust the speed between “FS.00” (flash off) to “FS.99” (fast-
est flash).
• n.XXX = This setting allows you to set the number of times you would
like each of the programs to cycle before moving on to the next pro-
gram.
Example: “n.002” means that the color change program will cycle twice,

©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 10©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 9
Mega Tri 60 Operating Instructions
then go to the next program, the next program will cycle twice, then
move on to the next program, and continue.
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When “G.XXX” is displayed you are in Green dimming mode. Press
the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the Flash (strobe) mode.
6. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).
DMX Mode:
Operating through a DMX controller givesthe user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The Mega Tri 60 has
6 DMX modes: 3 Channel mode, 5 Channel mode, 6 Channel mode, 8
Channel mode, 11 Channel mode, and a 29 Channel mode. See pages
14-20 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX Channel
mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
To run the 3 Channel Mode, press the MODE button until “CH-1”
is displayed. This is the 3 Channel DMX Mode.
To run the 5 Channel Mode, press the MODE button until “CH-2”
is displayed. This is the 5 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until “CH-3”
is displayed. This is the 6 Channel DMX Mode.
To run the 8 Channel Mode, press the MODE button until “CH-4”
Mega Tri 60 Operating Instructions
is displayed. This is the 8 Channel DMX Mode.
To run the 11 Channel Mode, press the MODE button until
“CH-5” is displayed. This is the 11 Channel DMX Mode.
To run the 29 Channel Mode, press the MODE button until
“CH-6” is displayed. This is the 29 Channel DMX Mode.
4. Please see pages 14-20 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
ADJ LED RC:
This function is used to activate and deactivate the ADJ LED RC
(Remote Control). When this function is activated you can control the
fixture using the ADJ LED RC. Please see the next page for ADJ LED
RC controls and functions.
1. Plug the fixture in and press the MODE button until “AUTO” is dis-
played.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents
either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).

©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 11 ©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 12
Mega Tri 60 ADJ LED RC Operation
The ADJ LED RC infrared remote (sold seperately) has many dif-
fernet functions and gives you complete control of your Mega Tri 60.
To control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away. To use the ADJ
LED RC you must first activate the fixtures infrared receiver, to acti-
vate the receiver please see the instructions on page 10.
BLACKOUT - Pressing this button will blackout the fixture.
AUTO RUN -This button will run an automatic program. You can set
the number of program cycles by pressing the SPEED button first and
then pressing the “+” and “-” buttons. See Auto Run Mode on page 8
for more information program cycles. You activate strobing by press-
ing the FLASH button, then using the “+” or “-” to adjust the flash
rate.
PROGRAM SELECTION -This button activates static color mode
and program mode. Pressing this button will switch between the two
modes.
In static color mode, use the “+” and “-” buttons to scroll through the
7 static colors. Press the Flash Button to activate strobing and use
the “+” & “-” buttons to adjust the strobe speed.
In program mode, use the “+” and “-” buttons to scroll through the 22
different programs.
Press the SPEED button and use the “+” and “-” buttons to adjust the
programs running speed.
Press the Flash Button to activate strobing and use the “+” & “-” but-
tons to adjust the strobe speed.
Press the Flash Button twice to enter the fade time setting and use
the “+” & “-” buttons to adjust the fade speed.
FLASH -This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
DMX MODE - This button will let you select which DMX mode you
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be pro-
grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” unit, press the MODE button until “Slav” is displayed.
Once “Slav” is displayed connect the “Slave” unit to the “Master.”
The “Slave” unit will now follow the “Master”.
Mega Tri 60 Master-Slave Configuration

want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 14-20 for DMX modes, values, and traits.
SOUND ACTIVE - This button activates sound active mode. Use the
“+” or “-” to adjust the sound sensitivity. Press the Flash Button to
activate strobing and use the “+” & “-” buttons to adjust the strobe
speed.
SLAVE - This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press “S-0-0-1”
Set DMX Address 245 Press “S-2-4-5”
R G B - Press either one of these buttons and the press the “+” or “-”
to adjust the brightness. Press the Flash Button to activate strobing
and use the “+” & “-” buttons to adjust the strobe speed.
“+” and “-” - Use these buttons to scroll through programs and static
colors, adjust the flash rate while strobing, adjust the speed of the
Auto Run and running programs, adjust the sound sensitivity, and to
adjust the intensity of the RGB colors.
DMX Control:
Operating through anDMX controller givesthe user the freedom to
create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX Mode and address.
1. Before connecting to an DMX controller, your fixture has different
DMX channel modes, please select your desired mode by press-
ing the DMX Mode button, then using the “+” or “-” buttons to
scroll through the DMX Channel Modes. Set the mode before you
address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the “S” button. When the “S” button is pressed
the LED’s will flash 2-3 times and all the red LED’s will light. Use
the number buttons to press in your desired address. See “SET
ADDRESS” on this page for examples.
Mega Tri 60 ADJ LED RC Operation
©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 13
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any
standard DMX controller. Please see pages 14-20 to for a detailed
descriptions of the DMX modes, values, and traits.
• If the Red LED’s glow you are in DMX Mode 1: 3 DMX Channels.
• If the Green LED’s glow you are in DMX Mode 2: 5 DMX
Channels.
• If the Blue LED’s glow you are in DMX Mode 3: 6 DMX Channels.
• If the Red & Green LED’s glow you are in DMX Mode 4: 8 DMX
Channels.
• If the Red & Blue LED’s glow you are in DMX Mode 5: 11 DMX
Channels.
• If the Green & Blue LED’s glow you are in DMX Mode 6: 29 DMX
Channels.
Mega Tri 60 ADJ LED RC Operation
©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 14
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
Mega Tri 60 3 Channel - DMX Values & Functions

©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 15 ©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 16
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 0 - 255 COLOR MACROS
(See Color Macros Table on page 21)
5 PROGRAMS
0 - 15 OFF
16 - 25 PROGRAM 1
26 - 35 PROGRAM 2
36 - 45 PROGRAM 3
46 - 55 PROGRAM 4
56 - 65 PROGRAM 5
66 - 75 PROGRAM 6
76 - 85 PROGRAM 7
86 - 95 PROGRAM 8
96 - 105 PROGRAM 9
106 - 115 PROGRAM 10
116 - 125 PROGRAM 11
126 - 135 PROGRAM 12
136 - 145 PROGRAM 13
146 - 155 PROGRAM 14
156 - 165 PROGRAM 15
166 - 175 PROGRAM 16
176 - 185 PROGRAM 17
186 - 195 PROGRAM 18
196 - 205 PROGRAM 19
206 - 215 PROGRAM 20
216 - 225 PROGRAM 21
226 - 235 PROGRAM 22
236 - 245 AUTO RUN
246 - 255 SOUND ACTIVE
Mega Tri 60 8 Channel - DMX Values & Functions
Channels 1, 2, and 3 will not work, when Channel 4 is being
used.
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 0 - 255 COLOR MACROS
(See Color Macros Table on page 21)
5 STROBING
0 - 7 NOTHING
8 - 255 STROBING SLOW - FAST
6 MASTER DIMMER
0 - 255 0% - 100%
Mega Tri 60 6 Channel - DMX Values & Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 STROBING
0 - 7 NO STROBING
8 - 255 STROBING SLOW - FAST
5 MASTER DIMMER
0 - 255 0% - 100%
Mega Tri 60 5 Channel - DMX Values & Functions

©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 17 ©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 18
Channel Value Function
6 PROGRAM SPEED/SOUND
SENSITIVITY
0 - 255 PROGRAM SPEED SLOW - FAST
0 - 255 SOUND SENSITIVITY
LEAST SENSITIVE - MOST SENSITIVE
7 STROBING
0 - 7 NOTHING
8 - 255 STROBING SLOW - FAST
8 MASTER DIMMER
0 - 255 0% - 100%
Channels 1, 2, and 3 will not work, when Channel 4 is being used.
When using Channel 5 values 16-235, Channel 6 will control the speed of the programs.
When using Channel 5 values 246-255, Channel 6 will control the sound sensitivity.
When using Channel 5 values 216-235, Channel 3 will select the moving color, while Channel 4
will select the base color, and Channel 6 will control the speed of the moving color.
Mega Tri 60 8 Channel - DMX Values & Functions
Channel Value Function
1 RED LEDs 1-3
0 - 255 0% - 100%
2 GREEN LEDs 1-3
0 - 255 0% - 100%
3 BLUE LEDs 1-3
0 - 255 0% - 100%
4 RED LEDs 4-6
0 - 255 0% - 100%
5 GREEN LEDs 4-6
0 - 255 0% - 100%
6 BLUE LEDs 4-6
0 - 255 0% - 100%
7 RED LEDs 7-9
0 - 255 0% - 100%
8 GREEN LEDs 7-9
0 - 255 0% - 100%
9 BLUE LEDs 7-9
0 - 255 0% - 100%
10 STROBING
0 - 7 NO STROBING
8 - 255 STROBING SLOW - FAST
11 MASTER DIMMER
0 - 255 0% - 100%
Mega Tri 60 11 Channel - DMX Values & Functions

©American DJ® - www.Americandj.com - Mega Tri 60 User Manual Page 19
Channel Value Function
1 RED LED 1
0 - 255 0% - 100%
2 GREEN LED 1
0 - 255 0% - 100%
3 BLUE LED 1
0 - 255 0% - 100%
4 RED LED 2
0 - 255 0% - 100%
5 GREEN LED 2
0 - 255 0% - 100%
6 BLUE LED 2
0 - 255 0% - 100%
7 RED LED 3
0 - 255 0% - 100%
8 GREEN LED 3
0 - 255 0% - 100%
9 BLUE LED 3
0 - 255 0% - 100%
10 RED LED 4
0 - 255 0% - 100%
11 GREEN LED 4
0 - 255 0% - 100%
12 BLUE LED 4
0 - 255 0% - 100%
13 RED LED 5
0 - 255 0% - 100%
14 GREEN LED 5
0 - 255 0% - 100%
15 BLUE LED 5
0 - 255 0% - 100%
16 RED LED 6
0 - 255 0% - 100%
17 GREEN LED 6
0 - 255 0% - 100%
Mega Tri 60 29 Channel - DMX Values & Functions
Channel Value Function
18 BLUE LED 6
0 - 255 0% - 100%
19 RED LED 7
0 - 255 0% - 100%
20 GREEN LED 7
0 - 255 0% - 100%
21 BLUE LED 7
0 - 255 0% - 100%
22 RED LED 8
0 - 255 0% - 100%
23 GREEN LED 8
0 - 255 0% - 100%
24 BLUE LED 8
0 - 255 0% - 100%
25 RED LED 9
0 - 255 0% - 100%
26 GREEN LED 9
0 - 255 0% - 100%
27 BLUE LED 9
0 - 255 0% - 100%
28 STROBING
0 - 7 NO STROBING
8 - 255 STROBING SLOW - FAST
29 MASTER DIMMER
0 - 255 0% - 100%
Mega Tri 60 29 Channel - DMX Values & Functions
©American DJ®- www.Americandj.com - Mega Tri 60 User Manual Page 20