ADLINK Technology NuPRO-760 User manual

NuPRO-760
Full-Size Socket 370 PICMG SBC
User’s Guide
Recycled Paper

©Copyright 2002 ADLINK Technology Inc.
Manual Rev. 1.11, October 16, 2003
Part NO: 50-13023-101
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
NuPRO is a registered trademark of ADLINK Technology Inc.,
Other product names mentioned herein are used for identification purposes
only and may be trademarks and/or registered trademarks of their respective
companies.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO
THE INSTRUCTIONS.

Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK TECHNOLOGY INC. If you
need any help or service, please contact us.
ADLINK TECHNOLOGY INC.
Web Site http://www.adlinktech.com
Sales & Service [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan
Please email or FAX your detailed information for prompt, satisfactory, and
consistent service.
Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
Environment
OS:
Computer Brand:
M/B: CPU:
Chipset: BIOS:
Video Card:
NIC:
Other:
Detail Description
Suggestions for ADLINK

Table of Contents •i
Table of Contents
Chapter 1 Introduction....................................................................1
1.1 Checklist......................................................................................... 2
1.2 Description..................................................................................... 2
1.3 Features .......................................................................................... 3
1.4 Specifications................................................................................. 4
1.5 Intelligence..................................................................................... 7
1.6 PCB Layout Drawing..................................................................... 8
1.7 Mechanical Drawing ...................................................................... 8
Chapter 2 Jumpers and Connectors...............................................9
2.1 Connectors on the NuPRO-760.................................................... 10
2.1.1 CN1,CN4 : IDE Pin Headers............................................................11
2.1.2 CN2 : FDD Pin Header....................................................................12
2.1.3 CN3 : Parallel Port Connector.........................................................12
2.1.4 CN5 : AC’97 Link PIN Header.........................................................13
2.1.5 CN6,CN7 : COM1,2 Serial Ports pin headers.................................13
2.1.6 CN8 : VGA Connector......................................................................13
2.1.7 CN9 : USB pin header......................................................................14
2.1.8 CN10 : Ethernet (RJ-45) Connector.................................................14
2.1.9 CN11 : IrDA interface Connector.....................................................14
2.1.10 CN12 : PS/2 Mouse Connector.........................................................14
2.1.11 CN13 : General Purpose System Signals..........................................15
2.1.12 CN15 : External keyboard connector ...............................................16
2.1.13 CN16 : PS/2 Keyboard Connector....................................................16
2.1.14 FAN1,FAN2 : CPU fan connector....................................................16
2.1.15 LED1 : LAN Activity Indicators........................................................17
2.1.16 CN17 : Case Open Connector ..........................................................17
2.1.17 CN18 : External LAN LED Pin-Header............................................17
2.1.18 CN19 : SMBus connector..................................................................17
2.2 Jumpers on NuPRO-760............................................................... 18
2.2.1 JP1 : DiskOnChip (MD2200) address select....................................19
2.2.2 JP2,3 : CPU host BUS frequency setting (FSB) ...............................20
2.2.3 JP4 : Clear CMOS RTC (real time clock) RAM ...............................21
Chapter 3 Watchdog Programming Guide..................................23

ii •Table of Contents
Chapter 4 VIA PLE133T Chipset Hardware and VGA Driver.25
4.1 Hardware Configuration File Installation..................................... 26
4.2 VGA Driver Installation............................................................... 29
Chapter 5 Realtek RTL8139C LAN Driver Installation.............31
5.1 Software and Drivers Support...................................................... 31
5.2 Driver Installation on Windows 2000 .......................................... 32
5.3 Driver Installation on Windows 98 .............................................. 33
5.4 Driver Installation on Windows NT............................................. 34
Product Warranty/Service.............................................................35

How to Use This Guide •iii
How to Use This Guide
This manual is designed to help you to use the NuPRO-760 series.
Chapter 1, “Introduction” gives an overview of the product features and
specifications.
Chapter 2, “Jumpers and Connectors” describes how to install the
SBC. The PCB layout, jumper setting and connector pin
assignments are shown.
Chapter 3 “Watchdog Programming” shows the functionality of the
watchdog timer.
Chapter 4, “VIA PLE133T Hardware and VGA Driver” describes how to
install the VGA and Hardware drivers of the VIA PLE133T
chipset.
Chapter 5, “Realtek RTL8139C LAN driver installation” describes how
to install the LAN driver for NuPRO-760 SBC.

Introduction •1
1
Introduction
This manual is designed to give you information on the NuPRO-760 series
CPU card. The information inside this user’s manual can be applied to
NuPRO-760 series if without specified.
The topics covered in this chapter are as follows:
•Checklist
•Description
•Features
•Specifications
•Intelligence
•PCB Layout Drawing
•Mechanical Drawing

2 •Introduction
1.1 Checklist
Please check that your package is complete and contains the items below. If
you discover damaged or missing items, please contact your dealer.
•The NuPRO-760 Industrial Computer Main Board
•This User’s Manual
•1 IDE Ribbon Cable (ATA-100)
•1 Floppy Ribbon Connector
•1 Serial Port Ribbon Cable and 1 Parallel Port Cable with bracket
•1 Serial Port Ribbon Cable with bracket
•1 CD Containing hardware configuration file, VGA Driver and LAN
Driver
1.2 Description
The NuPRO-760 is a single-CPU PICMG form factor, industrial computer
mainboard. The NuPRO-760 is based on the Intel PGA370 socket processor
with the VIA APOLLO PLE133T and VT82C686B chipset. It accommodates
single Intel Pentium III (Coppermine/Tualatin), Celeron and VIA C3
processor. This board supports three DIMM sockets and can accommodates
up to 1.5GB SDRAM configuration.
The VIA VT82C686B south bridge is embedded with hardware monitoring
device that monitors system and CPU temperature, system voltages, and
CPU, chassis fan speeds to prevent system crashes by warning the user of
adverse conditions. NuPRO-760 also has a case-open indicator for security.

Introduction •3
1.3 Features
•Single Pentium III (Coppermine/Tualatin) / Celeron (FC-PGA,
FC-PGA2) / VIA C3 processor with auto-selection of core voltages.
The Front Side Bus (FSB) frequency can be 66/100/133MHz
•VIA Apollo PLE133T (VT8601T) North Bridge Controller
•VIA VT82C686B super South Bridge Controller
•Up to 1.5GB PC-133 SDRAM system memory (3 x 168-pin DIMM
sockets)
•EIDE support up to Ultra/DMA100
•Two RS-232 interface
•One High speed bi-directional SPP/ECP/EPP parallel port
•Two USB ports
•One PS/2 Keyboard port and one PS/2 Mouse port
•Programmable watchdog timer
•Hardware Monitoring
•Single 10/100 Base-T Ethernet interface with external LAN status
LED connectors
•AC’97 Link interface support DB-AC97S board for audio input &
output
•ISA High Drive 64mA
•Standard ATX power connector on board
•The mounting holes around it to fit the board into chassis without
Backplane (When using standard ATX power connector as power
source)

4 •Introduction
1.4 Specifications
♦Processor Socket: Socket-370 connector
♦Processor: Intel Celeron and Pentium III (FC-PGA & FC-PGA2), VIA
C3 CPU
♦Secondary Cache: built in CPU
♦Bus Speed: 66/100/133MHz
♦Chipset: VIA PLE133T (VT8601T + VT82C686B)
♦Memory Sockets:
•Three 168-pin DIMM sockets
•Max. 1.5GB SDRAM
•Memory type: PC-133 un-buffered SDRAM
♦Integrated Graphics Controller:
•VIA 8601T built-in Trident 3D AGP 2D/3D graphics engine
•Video memory share with system memory up to 8MB
•AGP 4X, ACPI and VESA compliant
•Embedded 230MHz RAMDAC in chipset
•DDC2B compliant
•Support up to 1600x1200 resolution
♦BIOS: Award BIOS, support PnP
•DMI BIOS Support: Desktop Management Interface (DMI) allows
users to download system hardware-level information such as CPU
type, CPU speed, internal/external frequencies and memory size
•Green Function: Power management via BIOS, activated through
mouse/keyboard movement
♦PCI Compliance: Compliant to PCI rev. 2.2 standards, 32bit/33Mhz
interface.
♦PCI Bus Ethernet Interface:
•On-board Realtek RTL8139C high performance IEEE 802.3
10/100-BaseTX Ethernet controller
•Supports IEEE 802.3µ auto-negotiation for 10Base-T/100Base-TX

Introduction •5
•Supports IEEE 802.3x 100Base-TX flow control
•Reserved with pin-header for Ethernet’s LED for user’s applications
•Support Wake-On-LAN function and remote wake-up
♦Enhanced IDE: Bus Master IDE controller, two EIDE interfaces
support up to four IDE devices, including HDD, LS-120 and ATAPI
CD-ROM drives. Support PIO Mode 3/4 and Ultra DMA/33/66/100 IDE
devices. Onboard primary and secondary 40-pin IDE port.
♦Super I/O Chipset: Built-in VIA 82C686B chipset
♦Parallel Port:
•One high-speed parallel port, SPP/EPP/ECP mode
♦Serial Port:
•Two 16C550 UART compatible ports with RS-232 interface
♦FDD Interface: Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB,
2.88MB)
♦USB Interface: Two USB pin-header connectors, compliant with USB
Specification Rev. 1.1, Individual over-current protection
♦AC’97 Link:
•One 10 pin connector for DB-AC97S audio board
♦Watchdog Timer:
•Programmable I/O port 440h and 443h to configure watchdog timer
•Time-out timing select 0~255 seconds
♦Hardware Monitoring:
•Built-in VIA 82C686B, monitoring CPU temperature, CPU fan,
system temperature and DC Voltages
♦Keyboard and Mouse Connectors:
•One PS/2 Keyboard port and one PS/2 Mouse port
•One external 5-pin keyboard connector
♦Flash Disk Supporting:
•Support flash module DOM2000 (4MB~256MB) or 2.5” flash disk
Flash2000 (8MB~2GB) on IDE port

6 •Introduction
•Support DiskOnChip (DOC) up to 288MB
♦ISA High-drive: ISA bus high driving capability up to 64mA on all
address and control lines
♦Power supply: AT/ATX
♦Environmental:
•Storage Temperature: -20°C to 80°C
•Operation Temperature: 0°C to 60°C
•Humidity: 5% to 95%
♦Power Requirement:
Power Type Value (MAX) Unit Note
+5V 7400 mA
+12V 240 mA 1
–12V 100 mA
+5VSB 50 mA 2
1. Without FAN current.
2. When power-off and using ATX power supply
System configuration : NuPRO-760, Intel Pentium III/1GB (133MHz FSB),
1.5GB SDRAM (256MB PC-133 SDRAM x 3).
Note: The above values are the maximum power requirement for SBC
with CPU and RAM only, the CPU is running under full loading.
The power for all the other peripheral devices such as keyboard,
mouse, add-on cards, HDD, or CD ROM is not included.
♦Dimension: 338mm x 122mm(13.3” x 4.8”). Full-sized

Introduction •7
1.5 Intelligence
Socket 370
Socket 370
(PIII, Celeron or
(PIII, Celeron or
Tualatin )
Tualatin )
VIA APOLLO
VIA APOLLO
PLE133T
PLE133T
(VT8601T)
(VT8601T)
VIA 82C686B
VIA 82C686B
SOUTH BRIDGE
SOUTH BRIDGE
PCI BUS
PCI BUS
LAN
RTL 8139C
LAN
LAN
RTL 8139C
RTL 8139C
IDE2
IDE2
IDE2 IDE1
IDE1
IDE1
DUAL IDE
DUAL IDE
ATA 33/66/100
ATA 33/66/100
2
2
x USB
x USB
2
2
S
S
1
1
P
P
KB/MS
KB/MS
FLOPPY
FLOPPY
ISA BUS
ISA BUS
BIOS
BIOS
BIOS DOC 8MB
MD2200
DOC 8MB
DOC 8MB
MD2200
MD2200 WATCH DOG
TIMER
WATCH DOG
WATCH DOG
TIMER
TIMER
3
3 x DIMM x DIMM
66/100/133
66/100/133
MHZ
MHZ
CLK
Generator
(ICS9248
-39)
CLK
CLK
Generator
Generator
(ICS9248
(ICS9248
-
-39) 39)
Selectable FSB
Selectable FSB
66/100/133
66/100/133

8 •Introduction
1.6 PCB Layout Drawing
1.7 Mechanical Drawing

Jumpers and Connectors •9
2
Jumpers and Connectors
The connectors on the NuPRO-760 allow you to connect external devices
such as keyboard, floppy disk drives, hard disk drives, printers, etc.
The following subsections specify the pin assignments for the connectors
and jumper blocks on NuPRO-760.
•CN1, CN4: EIDE Connectors (CN1: primary)
•CN2: Floppy Drive Connector
•CN3: Parallel Port Connector
•CN5: AC’97 Connector
•CN6, CN7: Serial Port (CN7: COM1, CN6: COM2)
•CN8: VGA CRT Connector
•CN9: USB Connector
•CN10: Ethernet RJ45 Connector
•CN11: IrDA interface connector
•CN12: PS/2 Mouse Connector
•CN13: General Purpose System Signals
•CN14: ATX Power Connector
•CN15: External keyboard connector
•CN16: PS/2 Keyboard Connector
•CN17: Case Open connector
•CN18: External LAN LED pin-header

10 •Jumpers and Connectors
•CN19: SMBus connector
•FN1,FN2: CPU fan connector
•LED1: LAN Activity Indicators
2.1 Connectors on the NuPRO-760
CN8
CN10
CN12
CN16:
CN15:
CN3
CN6
CN9
FN2
CN2
CN11
FN1
CN1
CN4:
LED1
CN7
CN17
CN19
CN18
CN13
CN14
CN5

Jumpers and Connectors •11
2.1.1 CN1,CN4 : IDE Pin Headers
CN1: Primary IDE Connector, CN4: Secondary IDE Connector
Signal Name Pin # Pin # Signal Name
Reset IDE 1 2 Ground
Host data 7 3 4 Host data 8
Host data 6 5 6 Host data 9
Host data 5 7 8 Host data 10
Host data 4 9 10 Host data 11
Host data 3 11 12 Host data 12
Host data 2 13 14 Host data 13
Host data 1 15 16 Host data 14
Host data 0 17 18 Host data 15
Ground 19 20 +5V
(2)
DRQ0 / DRQ1(1) 21 22 Ground
Host IOW 23 24 Ground
Host IOR 25 26 Ground
IOCHRDY 27 28 Host ALE
DACK0 / DACK1 (1) 29 30 Ground
IRQ14 / IRQ 15(1) 31 32 No connect
Address 1 33 34 No connect
Address 0 35 36 Address 2
Chip select 0 37 38 Chip select 1
Activity 39 40 Ground
Note :
(1) The signals are with different definitions for primary or secondary IDE
(2) The pin #20 provide +5V power, which is used to support the direct
plug-in Disk On Module (DOM: IDE flash disk).

12 •Jumpers and Connectors
2.1.2 CN2 : FDD Pin Header
Signal Name Pin # Pin # Signal Name
Ground 1 2 Drive density selection
Ground 3 4 No connect
Ground 5 6 Drive density selection
Ground 7 8 Index
Ground 9 10 Motor enable 0
Ground 11 12 Drive select 1
Ground 13 14 Drive select 0
Ground 15 16 Motor enable 1
Ground 17 18 Direction
Ground 19 20 Step
Ground 21 22 Write data
Ground 23 24 Write gate
Ground 25 26 Track 00
Ground 27 28 Write protect
Ground 29 30 Read data
Ground 31 32 Side 1 select
Ground 33 34 Diskette change
2.1.3 CN3 : Parallel Port Connector
Signal Name Pin # Pin # Signal Name
Line printer strobe 1 14 AutoFeed
PD0, parallel data 0 2 15 Error
PD1, parallel data 1 3 16 Initialize
PD2, parallel data 2 4 17 Select
PD3, parallel data 3 5 18 Ground
PD4, parallel data 4 6 19 Ground
PD5, parallel data 5 7 20 Ground
PD6, parallel data 6 8 21 Ground
PD7, parallel data 7 9 22 Ground
ACK, acknowledge 10 23 Ground
Busy 11 24 Ground
Paper empty 12 25 Ground
Select 13 N/A N/A