ADLINK Technology cPCI-6880 Series User manual

1 of 40
cPCI-R6000,cPCI-R6100, cPCI-R6200
6U Compact PCI® Rear Transition Modules
User’s Manual
Manual Rev. 1.04
Revision Date: July 23, 2009
Part No: 50-15066-1000(EA)
Revision History
Revision Release Date Description of Change(s)
1.00 PM draft (Chapters 3, 6 & 8
are not ready)
1.01 June 3, 2009 Jack's revisions
1.02 June 22,2009 PM’s revisions
1.03 Jun 25, 2009 PM’s revisions
1.04 July 13, 2009 1. Remove LVDS feature
2. Update CN10 pin definition
3. Add J4 pin assignment
4. Update cPCI-R6000D

2 of 40
drawing
5. Update HDD& CF installation
on cPCI-R6000D
1.05 July 28, 2009 Add T3100 processor
support

3 of 40
Preface
Copyright 2009 ADLINK TECHNOLOGY INC.
This document contains proprietary information protected by copyright. All rights are reserved. No part
of this manual may be reproduced by any mechanical, electronic, or other means in any form without
prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve reliability,
design, and function and does not represent a commitment on the part of the manufacturer. In no event
will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising
out of the use or inability to use the product or documentation, even if advised of the possibility of such
damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global environmental preservation through
compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste
Electrical and Electronic Equipment (WEEE) directive. Environmental protection is a top priority for
ADLINK. We have enforced measures to ensure that our products, manufacturing processes, components,
and raw materials have as little impact on the environment as possible. When products are at their end of
life, our customers are encouraged to dispose of them in accordance with the product disposal and/or
recovery programs prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or
registered trademarks of their respective companies.

4 of 40
Table of Contents
1Overview..............................................................................................................................5
1.1 Introduction..............................................................................................................5

5
1 Overview
1.1 Introduction
The cPCI-6880 Series is a 6U CompactPCI single board computer in single slot (4HP)
width form factor featuring a low power Intel® mobile chipset and 45nm CoreTM2 Duo
processor with high performance 1066MHz front-side bus (FSB). The cPCI-6880
provides up to 8GB dual channel DDR2-667/800 memory capacity, one channel of
soldered onboard memory up to 4GB, and the other channel via SODIMM socket. The
cPCI-6880 Series implements the Mobile Intel® GM45 Memory Controller Hub and
ICH9M I/O Hub for optimal performance.
The cPCI-6880 Series supports a 64bit/66MHz CompactPCI bus, one PMC site with
64-bit/66MHz PCI bus, four PCI-Express® Gigabit Ethernet ports (two on front panel,
two for PICMG 2.16), a SATA connector for an onboard 2.5” SATA HDD (or
CompactFlash socket via adapter), onboard 4GB USB NAND flash for solid-state
storage, and SCSI RAID 1 support via the Rear Transition Module (RTM). For flexibility
of use, the cPCI-6880 Series can be installed in a standard CompactPCI system slot as
system master, or peripheral slot as PCI device. The cPCI-6880 Series is ideally suited
for factory automation, transportation and military applications.

6
Appendix
Rear Transition Modules
There are some Rear Transition Modules available to mate with the cPCI-6510 to get
extensive I/O interfaces.
cPCI-R6000-NF
cPCI-R6000-NF Specification
Mechanical Standard 6U CompactPCI® rear I/O
Board size: 233.35mm x 80mm
Single slot (4HP, 20.32mm)
CompactPCI® connectors rJ3 and rJ5
Faceplate I/O 2x USB2.0 ports
2x 10/100/1000BAST-T Ethernet ports
DVI-I port
DB-15 serial port
External 68-pin SCSI socket
Onboard
Peripherals
USB 2.0 5-pin header
RS-232 10-pin header (Tx, Rx signal only)
Internal 68-pin SCSI socket
2x 7-pin Serial ATA connectors
SCSI LSI® Logic LSI53C1020 PCI-X Ultra320 SCSI Controller
Integrated RAID on PCI-X 64-bit/133MHz bus
320MB per second data transfer rate
Supports RAID 1 (mirroring)

7
cPCI-R6000-NF Block Diagram
cPCI-R6000 Package Contents
The cPCI-R6000 is packaged with the following components. If any of the items on the
contents list are missing or damaged, retain the shipping carton and packing material and
contact the dealer for inspection. Please obtain authorization before returning any product
to ADLINK. The packing contents of the cPCI-R6000 Series are non-standard
configurations and may vary depending on customer requests.
The cPCI-R6000 Series
DVI to VGA (DB-15) adapter
Ultra-320 SCSI cable
The cPCI-R6000P Series
DVI to VGA (DB-15) adapter
The cPCI-R6000D Series
The DB-6920SAT daughter board
HDD screw pack
Face- Plate
GbE x2 (PICMG 2.16)
COM
USB x2
7 pin
7 pin
SATA
TMDS
RGB
DVI-I
FDD
PLX®
PEX8114 SCSI
PCI-X
64bit/133MHz
PCI-E x4
rJ5
rJ3
SATA
10 pin
RS232 (Tx, Rx)
USB9 5 pin

8
2.5” HDD bracket
Y-cable for PS/2 combo port
DVI to VGA (DB-15) adapter
Ultra-320 SCSI cable
Optional orderable Adapter kit:
The DB-CF-SA kit
□ DB-6920CF adapter board
□ Screw pack
□ CF card guide
Note: The contents of non-standard cPCI-R6200 Series configurations may vary
depending on the customer’s requests.

9
cPCI-R6000-NF Board Layout
U26 PCI-E to PCI bridge CN12 External SCSI
connector
U31 LSI53C1020 SCSI
controller CN15/16 USB ports
JP1 USB pin header (5-pin) CN20/21 GbE ports
CN1/2 SATA port (7-pin) CNY1 DVI-I Connector
CN5 Internal SCSI connector rJ3/5 CompactPCI
Connectors
CN9 Serial port SW1/2/3/4 Swiches
CN10 Serial 10 pin header
(Tx,Rx only)
cPCI-R6000-NF Connector Pin Assignment
U31
rJ5
CN5
JP1
CNY1
CN9
CN12
CN2
CN16/15CN20/21
U26
rJ3
CN10 CN1
SW1
SW2
SW3
SW4 No Population
No Population

10
USB Connectors (CN15, CN16)
Onboard USB Connector (JP1)
1VCC
2USB_N
3USB_P
4GND
5CH_GND
1

11
RJ-45 Gigabit Ethernet Connectors (CN20, CN21)
Pin# GbE1 Signal Function
1 LANB_TX0P Media Dependent Interface 1+
2 LANB_TX0N Media Dependent Interface 1-
3 LANB_TX1P Media Dependent Interface 2+
4 LANB_TX1N Media Dependent Interface 2-
5 LANB_TX2P Media Dependent Interface 3+
6 LANB_TX2N Media Dependent Interface 3-
7 LANB_TX3P Media Dependent Interface 4+
8 LANB_TX3N Media Dependent Interface 4-
Ethernet Status Speed
(Green/ Amber) Activity (Amber)
Network link is not established or
system power off OFF OFF
Link OFF ON10 Mbps
(10 Base) Active OFF Blinking
Link Amber ON100 Mbps
(100 Base) Active Amber Blinking
Link Green ON1000 Mbps
(1000 Base) Active Green Blinking
Activity Speed

12
DB-9 Serial Port (CN9)
Onboard Serial Port Connector (CN10)
DVI-I Connector (CNY1)
Pin # Signal Pin # Signal
1 TMDS Data2- 16 Hot Plug Detect
Pin # RS-232
1 DCD, Data carrier detect
2 RXD, Receive data
3 TXD, Transmit data
4 DTR, Data terminal ready
5 IsoGND, Isolated ground
6 DSR, Data set ready
7 RTS, Request to send
8 CTS, Clear to send
9 RI, Ring indicator
Pin # RS-232
1 Not used
2 Not used
3 RXD, Receive data
4 Not used
5 TXD, Transmit data
6 Not used
7 Not used
8 Not used
9 IsoGND, Isolated ground
10 Not used

13
2 TMDS Data2+ 17 TMDS Data0-
3 TMDS Data2/4 Shield 18 TMDSData0+
4 TMDS Data4- 19 TMDS Data0/5 Shield
5 TMDS Data4+ 20 TMDS Data5-
6 DDC Clock [SCL] 21 TMDS Data5+
7 DDC Data [SDA] 22 TMDS Clock Shield
8 Analog vertical sync 23 TMDS Clock +
9 TMDS Data1- 24 TMDS Clock -
10 TMDS Data1+ C1 Analog Red
11 TMDS Data1/3 Shield C2 Analog Green
12 TMDS Data3- C3 Analog Blue
13 TMDS Data3+ C4 Analog Horizontal
Sync
14 +5 V Power C5 Analog GND Return:
(analog R, G, B)
15 GND
7-pin Serial ATA Connector (CN1, CN2)
Pin# Signal
1 GND
2 TX+
3 TX-
4 GND
5 RX-
6 RX+
7 GND

14
68-pin Vertical SCSI Connector (CN12)

15
Signal Name Pin # Pin # Signal Name
SCSI-SDP12 1 35 SCSI-SDN12
SCSI-SDP13 2 36 SCSI-SDN13
SCSI-SDP14 3 37 SCSI-SDN14
SCSI-SDP15 4 38 SCSI-SDN15
SCSI-SDP1-P1 5 39 SCSI-SDP1-N1
SCSI-SDP0 6 40 SCSI-SDN0
SCSI-SDP1 7 41 SCSI-SDN1
SCSI-SDP2 8 42 SCSI-SDN2
SCSI-SDP3 9 43 SCSI-SDN3
SCSI-SDP4 10 44 SCSI-SDN4
SCSI-SDP5 11 45 SCSI-SDN5
SCSI-SDP6 12 46 SCSI-SDN6
SCSI-SDP7 13 47 SCSI-SDN7
SCSI-SDP0-P0 14 48 SCSI-SDP0-N0
GND 15 49 GND
DIFFSEN 16 50 NC
P3V3_SCSI 17 51 P3V3_SCSI
P3V3_SCSI 18 52 P3V3_SCSI
NC 19 53 NC
GND 20 54 GND
SCSI-SATN-P 21 55 SCSI-SATN-N
GND 22 56 GND
SCSI-SBSY-P 23 57 SCSI-SBSY-N
SCSI-SACK-P 24 58 SCSI-SACK-N
SCSI-SRST-P 25 59 SCSI-SRST-N
SCSI-SMSG-P 26 60 SCSI-SMSG-N
SCSI-SSEL-P 27 61 SCSI-SSEL-N
SCSI-SCD-P 28 62 SCSI-SCD-N
SCSI-SREQ-P 29 63 SCSI-SREQ-N
SCSI-SIO-P 30 64 SCSI-SIO-N
SCSI-SDP8 31 65 SCSI-SDN8
SCSI-SDP9 32 66 SCSI-SDN9
SCSI-SDP10 33 67 SCSI-SDN10
SCSI-SDP11 34 68 SCSI-SDN11
1
34
35
68

16
cPCI-R6000-NF Switches and Jumper Settings
PICMG 2.16 Switches (SW1 ,SW2, SW3, SW4)
All switches are set to ON by default
SW1-R SW2-R SW3-R SW4-R
The cPCI-R6000-NF RTM supports GbE3 and GbE4 on either the 2.16 backplane or via
Rear I/O. The GbE3 and GbE4 signals cannot be accessed simultaneously by both the
PICMG® 2.16 backplane and Rear I/O . SW1 to SW4 must be set to either the 2.16
backplane or to Rear I/O. The following table shows how to set the switches to enable
GbE3 and GbE4 to either the 2.16 backplane or to Rear I/O.
Connected to : GbE3 (SW1 and SW2) GbE4 (SW3 and SW4)
PICMG® 2.16 Backplane ALL OFF ALL OFF
Rear faceplate RJ-45
connectors ALL ON (default) ALL ON (default)
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4

17
cPCI-R6100, cPCI-R6110
The cPCI-R6100 and cPCI-R6110 have the same electrical design but different features
by BOM option. Refer to below specification for detail.
cPCI-R6100, cPCI-R6110 Specification
Mechanical Standard 6U CompactPCI® rear I/O
Board size: 233.35mm x 80mm
Single slot (4HP, 20.32mm)
CompactPCI® connectors rJ3 and rJ5
Faceplate I/O cPCI-R6100:
4x USB2.0 ports
4x 10/100/1000BAST-T Ethernet ports
DVI port
DB-15 VGA port
RJ-45 Serial port
PS/2 Keyboard Mouse port
cPCI-R6110:
4x USB2.0 ports
2x 10/100/1000BAST-T Ethernet ports
DB-15 VGA port
PS/2 Keyboard Mouse port
Onboard
Peripherals cPCI-R6100:
2x 7-pin Serial ATA connectors
Type II CompactFlash socket (converted from USB)
SD (Secure Digital Memory Card) socket
cPCI-R6110:
Direct Serial ATA connector for 2.5” HDD
2x 7-pin Serial ATA connectors
Type II CompactFlash socket (converted from USB)
SD (Secure Digital Memory Card) socket
Ethernet Two 10/100/1000BASE-T ports (GbE 3 & 4) are switched
from PICMG 2.16

18
One Intel 82576EB Gigabit Ethernet Controller on RTM for
additional two Gigabit Ethernet ports (GbE 5 & 6)
Miscellaneous Optional Gold Cap for time keeping in case there is no
Battery in SBC. (depopulation by default)

19
cPCI-R6100 Block Diagram
Face- Plate
GbE 3/4 (PICMG 2.16)
COM
USB x4
7 pin
SATA
SATA
TMDS DVI
GbE 5
PCI-E x4
PS/ 2 KB/MS
USB9
VGA
SD
Intel
82576EB GbE 6
GL826
Gold Cap
CF
7 pin
RTC
rJ5
rJ3
SATA 2.5” HDD

20
cPCI-R6100/cPCI-R6110 Package Contents
The cPCI-R6100 is packaged with the following components. If any of the items on the
contents list are missing or damaged, retain the shipping carton and packing material and
contact the dealer for inspection. Please obtain authorization before returning any product
to ADLINK. The packing contents of the cPCI-R6200 Series are non-standard
configurations and may vary depending on customer requests.
Rear Transition Module:
The cPCI-R6100, cPCI-R6101 module
Y-cable for PS/2 combo port
The cPCI-R6110, cPCI-R6111 module
The DB-6920SAT daughter board
HDD screw/standoff pack
Y-cable for PS/2 combo port
Optional orderable Adapter kit:
The DB-CF-SA kit (for cPCI-R6110)
□ DB-6920CF adapter board
□ Screw pack
□ CF card guide
Note: The contents of non-standard cPCI-R6100 Series configurations may vary
depending on the customer’s requests.