ADT BHS-4000A User manual

QuickGuide:BHS-4000A
Page 1of 3
For a detailed review of the entire system, please view the BHS 4000A system manual.
Arm and Disarm
Arm:
•To arm in Away Mode, press the [On] button located on the system panel.
o Whenthe[OnLight]beginstoflash,thestandard80seconddelayperiodhas
begun.
oWhen the [On Light] becomes steady, the system is armed.
oTo arm in Away Instant Mode, press the [ON] button, then press the [Instant]
button.
o
• To arm inStay Mode, press the [On] button, then press the [Motion Off] button.
• To arm in Stay Instant Mode, press the [On] button, then the [Motion Off] button, then
press the [Instant] button .
Disarm:
▪To disarm, enter your [security code] + [Cancel] within the 20 second delay period.
▪The [On Light] will no longer be lit once the system is disarmed.

Page 2of 3
Battery
•The BHS –400A operates on a UB 1270 battery.
•Loss of AC power and use of backup battery power is indicated by NO AC.
•A low battery condition is indicated by BAT.
For instructions on replacing your battery, please visit our Battery Replacement Page.
Bypassing Protected Areas
Bypassingazoneallowsyoutoarmyoursystemwithcertainprotectedareasintentionally
unarmedorto accessaprotectedareawhenthesystemisarmed.
• Tobypassazone,pressthe[Options]buttonuntilthedisplayshows[Bypass,Enter
Zone#].
• Enterthezonenumberyouwishtobypass.
•The display will flash the zone number and show [Ready, Bypass].
•Press [On] to arm the system with zones bypassed.
ChimesandBeeps
Whenyoursystemisinchimemode,achimealertwillsoundwheneveraprotected
door/windowisopened.
• To turnchimemodeon,press the [Options]buttonuntil the window shows [Door
Chime].
•Enter your [security code] to select this option. The display window will show [Ready
Door Chime].
•To turn Chime mode off, press the [Cancel] button, otherwise it will turn off
automatically when the system is turned on.
Reset
•To reset the system after an alarm event, first enter your [security code].
•Then, to view the event, press the [Options] button until the display shows [Alarm
Memory, Enter Code] + your [security code].

Page 3of 3
Security Codes
Yoursystemallowsupto6 differentsecuritycodesforusebyotherusers.
•To add a user code, press the [Options] button until the display window shows
[Auxiliary Code, Enter Master Code].
•Enter your [Master Security Code].
•Select the desired number to assign. The window will then show [Enter New Code].
•Enter the new user’s code.
•The keypad will audibly confirm that the system accepted the new code.
•To delete a user code, press the [Options] button until the display window shows
[Auxiliary Code, Enter Master code].
•Enter your [Master Security Code]. The window shows [Enter 1-6].
• Enterthe usernumberyouwouldliketo delete.
•The display will show [Enter new Code]. Do not enter the auxiliary code. Press [Cancel] to
delete the code.
• Thekeypadwillaudiblyconfirmthedeletionfromthesystem.
The Master Code cannot be changed at the keypad. Please contact Customer Care for
assistance.
Trouble Conditions
Your security system is able to automatically test itself for power failures, low batteries,
nonworking sensors, and communication troubles with the central monitoring station. In the
event that your system does have a trouble condition, refer to the tables below to identify the
trouble code and resolve your issue.
To silence trouble beeps, press [CANCEL] twice.
For a complete list of Trouble Conditions, please refertotheBHS3000 and4000Troubleshooting
page.
Volume
The volume on the BHS 4000A is not adjustable.