ADTRAN AOC QSFP28 100G AOC QSFP28 100G 3M User manual

Q
uic
k
Start
DESCRIPTION
The following products are supported in this document:
The Active Optical Cable (AOC) Quad Small Form Pluggable
(AOC QSFP28) is a multimode fiber cable with optical trans-
ceivers on both ends that is used to create optical links of up to
100 GB/s.
The AOC QSFP28 provides full duplex and parallel interconnects:
4 transmitting / 4 receiving data lanes.
Part Number Description
1445019F3C QSFP28 100G 3M
1445019F10C QSFP28 100G10M
1445019F15C QSFP28 100G 15M
1445019F20C QSFP28 100G 20M
1445019F30C QSFP28 100G 30M
1445019F50C QSFP28 100G 50M
1445019F100C QSFP28 100G 100M
INSTALLATION
To install the AOC QSFP28 into an appropriate module, complete
the following steps:
1. Inspect the AOC QSFP28. If damaged, file a claim with the
carrier and then contact ADTRAN Customer Service.
2. Do not remove the protective end cap from the QSFP until
the fiber optic cable is ready to be connected.
3. Insert the AOC QSFP28 into the QSFP cage on the module.
Ensure the manufacturer’s label on the QSFP is facing
upward for correct installation.
4. Slide the AOC QSFP28 all the way into the receptacle until
there is an audible “click.”
f
CAUTION!
Due to compliance certification requirements, use only QSFPs
supplied by ADTRAN. ADTRAN cannot certify system integrity
with other QSFPs.
wNOTICE
The loop on the QSFP is used to remove the QSFP from the cage
on the circuit card.
ADTRAN Pluggable Optics
AOC
AOC QSFP28 100G
May 2017
61445019F3C-13A
P/N: 1445019F3C

2 61445019F3C-13A
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises.
■This product and the host system are designed and intended
for installation as part of a Common Bonding Network (CBN).
This product and the host system are not designed nor
intended for installation as part of an Isolated Bonding Network
(IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (i.e., front
panels, SFP/XFP modules) on the product is properly
grounded.
gNOTE
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is designed to be deployed in GR-3108-CORE
environmental class 1.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has also been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1.
This product meets the requirements for CE marking under the
EMC Directive and Low Voltage Directive. Standards used to
demonstrate Compliance are EN 300 386 and EN 60950.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental condi-
tions; Storage Class” 1.2
♦ETSI EN 300 019-2-2 “Classification of environmental condi-
tions, Transportation”, Class 2.3
♦ETSI EN 300 019-2-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations”, Class
3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-2-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
OPERATIONAL SPECIFICATIONS
General
■Module type: QSFP28
■Fiber/Copper: Fiber
♦SM/MM: Multimode Fiber
■Applications: 40 GbE and 10 GbE break-out applications, High
performance computing interconnect
■Distance: Different lengths from 3,10,15, 20, 30, 50, and 100
meters
■Digital Diagnostic Monitoring: SFF8636 Compliant
Optical
■Transmitter
♦Laser Diode Type: VCSEL Array
♦Tx Central Wavelength: 850 nm
■Receiver
♦Rx Type: PIN Array
♦Rx Central wavelength: 850 nm
Environmental
■Controlled Environment (Commercial Grade)
■Operational temperature range: –5°C to + 50°C
■Storage temperature range: –40°C to +85°C
■Relative humidity to 80%, noncondensing
SAFETY AND REGULATORY
ENGLISH
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product contains or uses a Class 1 Laser module that
complies with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-1.
For continued compliance with the above standards, only
approved Class 1 laser modules from an ADTRAN approved
vendor list (located on the ADTRAN website) should be installed
in this product. ADTRAN cannot certify system integrity with other
laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. The

61445019F3C-13A 3
FRANÇAIS
fAVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
Ce produit contient ou utilise un module Laser de classe 1 qui est
conforme avec la FDA 21 CFR 1040.10, 1040.11 et IEC 60825-1.
Pour le maintien de la conformité avec les normes ci-dessus,
seulement approuvé classe 1 modules laser d'un ADTRAN
approuvés liste des fournisseurs (situé sur le site ADTRAN) doit
être installé dans ce produit. ADTRAN ne peut certifier l'intégrité
du système avec d'autres modules laser.
fATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules SFP / XFP) sur le produit est correctement
mis à la terre via le connecteur de fond de panier.
gREMARQUE
■Ce produit a été évalué selon les normes internationales de
sécurité EN 60950-1, AS/NZS 60950.1, et IEC 60950-1. Ce
produit répond aux exigences de la directive CEM et de la
directive basse tension pour le marquage CE. Les normes
utilisées pour démontrer la conformité du produit sont les
normes EN 300 386 et EN 60950.
■Ce produit est conçu pour répondre aux classes
environnementales suivantes:
♦ETSI EN 300 019-2-1: “Classification des conditions
d'environnement; Entreposage,” classe 1.2
♦ETSI EN 300 019-2-2: “Classification des conditions
d'environnements; Transport,” classe 2.3
♦ETSI EN 300 019-2-3: “Classification des conditions
d'environnements; l'utilisation à poste fixe dans des endroits
protégés contre les intempéries,” classe 3.1E
■L'équipement est conçu pour fonctionner sans degradation
lors des tests à tous les niveaux de sévérité, suivant les
spécifications de la classe 3.3 de l'ETSI EN 300 019-2-3.
■Ce produit est conforme à la directive. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C
VORSICHT!
DasProdukt enthält oder verwendet Klasse 1 Laser-Module, die
60825-1 mit FDA 21 CFR 1040.10, 1040.11 und IEC erfüllen.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Klasse 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (siehe Website von ADTRAN). ADTRAN garantiert nicht
für die Systemintegrität bei anderen Lasermodulen
f
VORSICHT!
■Elektrostatische Entladung (ESD) können elektronische
Baugruppen beschädigt werden. Beim Umgang mit Modulen ,
tragen Sie eine Antistatikarmband, um Schäden an
elektronischen Bauteilen zu verhindern. Ort -Module in
antistatische Verpackung, beim Transport oder Lagerung. Bei
Arbeiten an Modulen immer legen Sie sie auf einer
zugelassenen antistatische Unterlage, die elektrisch geerdet
ist.
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, SFP / XFP-Module) auf dem Produkt
richtig über den Backplane-Anschluss geerdet ist.
g
HINWEIS
■Dieses Produkt wurde nach den internationalen
Sicherheitsnormen EN 60950-1, AS/NSZ 60950.1 und IEC
60950-1 bewertet. Dieses Produkt erfüllt die Anforderungen
der CE-Kennzeichnung gemäß der EMV-Richtlinie und der
Niederspannungsrichtlinie. Die zum Nachweis der Konformität
herangezogenen Normen sind EN 300 386 und EN 60950.
■Dieses Produkt wurde entsprechend der folgenden
Umweltklassen entwickelt:
♦ETSI EN 300 019-2-1 “Klassifizierung von Umweltbedin-
gunge”; Storage Class 1,2
♦ETSI EN 300 019-2-2”, Klassifizierung von Umweltbedin-
gungen,Transportation”, der Klasse 2.3
♦ETSI EN 300 019-2-3 “Klassifizierung von Umweltbedin-
gungen, Ortsfester Einsatz, wettergeschützten Standorten”
Klasse 3.1E
■Dieses Gerät funktioniert ohne Leistungsabfall während aller
für Klasse 3.3 von ETSI EN 300 019-2-3 vorgeschriebenen
Belastungstests.
■Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen
Sie www.adtran.com für ausführlichere Informationen zu
RoHS/WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2016 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61445019F3C-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)