ADTRAN DSU IV ESP User manual

DSU IV ESP
Data Service Unit with Embedded SNMP
User Manual
61204011L1-1B
May 2001
Part Number
1204011L1
1204001L1
1204002L2
1204004L1
1204005L1
Version
DSU IV ESP
ESP 4-wire Switched 56 DBU Card
ESP V.34 DBU Card
ESP ISDN DBU Card
ESP Ethernet Card

Trademark Information:
Hayes is a registered trademark of Hayes Microcomputer Products, Inc.
Openview is a registered trademark of Hewlett-Packard Company.
SunNet Manager is a registered trademark of Sun Microsystems, Inc.
Netview is a registered trademark of IBM
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
[phone]
© 2001 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.

iii
The following conventions are used in this manual.
Important Safety Instructions
When using your telephone equipment, please follow these basic safety precautions
to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as near a bathtub, wash bowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm.
There is a remote risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual.
Do not dispose of batteries in a fire. They may explode. Check with local codes for
special disposal instructions.
Save These Important Safety Instructions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.

iv
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company whenever digital
terminal equipment without encoded analog content and billing protection is
used to transmit digital signals containing encoded analog content which are
intended for eventual conversion into voice band analog signal and transmitted
on the network.
• The affidavit shall affirm that either no encoded analog content or billing informa-
tion is being transmitted or that the output of the device meets Part 68 encoded
analog content or billing protection specification.
• End use/customer will be responsible to file an affidavit with the local exchange
carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital ser-
vice.
• Until such time as subrate digital terminal equipment is registered for voice appli-
cations, the affidavit requirements for subrate services are waived.

v
Affidavit for Connection of Customer Premises Equipment to 1.544 MBPS and/
or Subrate Digital Services
For the work to be performed in the certified territory of ______________ (telco name)
State of ________________________________
County of ______________________________
I, _______________________ (name), ____________________ (business address),
_____________________ (telephone number) being duly sworn, state:
I have the responsibility for the operation and maintenance of the terminal equipment
to be connected to 1.544 Mbps and/or __________________ subrate digital services.
The terminal equipment to be connected complies with Part 68 of the FCC rules
except for the encoded analog content and billing protection specification.With
respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance and adjust-
ment of the digital CPE with respect to encoded analog content and billing protection
information continuously complies with Part 68 of the FCC rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog con-
tent or billing information which is intended to be decoded within the telecommuni-
cations network.
( ) The encoded analog content and billing protection is factory set and is not under
the control of the customer.
I attest that the operator(s) maintainer(s) of the digital CPE responsible for the estab-
lishment, maintenance and adjustment of the encoded analog content and billing
information has (have) been trained to perform these functions by successfully having
completed one of the following (check appropriate blocks):
( ) A. A training course provided by the manufacturer/grantee of the equipment used
to encode analog signals; or
( ) B. A training course provided by the customer or authorized representative, using
training materials and instructions provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) C. An independent training course (e.g., trade school or technical institution) rec-
ognized by the manufacturer/grantee of the equipment used to encode analog sig-
nals; or

vi
( ) D. In lieu of the proceeding training requirements, the operator(s)/maintainer(S) is
(are) under the control of a supervisor trained in accordance with _______________
(circle one) above.
I agree to provide ____________________ (telco’s name) with proper documentation
to demonstrate compliance with the information in the preceding paragraph, if so
requested.
_____________________ Signature
_____________________ Title
_____________________ Date
Subscribed and sworn to before me
This _________ day of ___________________, 20__
_______________________________________
Notary Public
My commission expires: _________________________

vii
FCC regulations require that the following information be provided in this man-
ual:
1. This equipment complies with Part 68 of the FCC rules. On the bottom of the
equipment housing is a label that shows the FCC registration number and Ringer
Equivalence Number (REN) for this equipment, if applicable. If required, this
information must be given to the telephone company.
2. The following information may be required when applying to the local telephone
company for leased line facilities.
3. An FCC compliant telephone cord with a modular plug may be provided with
this equipment. This equipment is designed to be connected to the telephone net-
work or premises wiring using a compatible modular jack, which is FCC Part 68
compliant. See installation instructions for details.
4. If this equipment causes harm to the telephone network, the telephone company
may temporarily discontinue service. If possible, advance notification is given;
otherwise, notification is given as soon as possible. The telephone company will
advise the customer of the right to file a complaint with the FCC.
5. The telephone company may make changes in its facilities, equipment, operations,
or procedures that could affect the proper operation of this equipment. If this hap-
pens, the telephone company will provide advance notification and the opportunity
to make the necessary modifications to maintain uninterrupted service.
6. If experiencing difficulty with this equipment, please contact ADTRAN for repair and
warranty information. If the equipment is causing harm to the network, the telephone
company may request this equipment to be disconnected from the network until the
problem is resolved or it is certain that the equipment is not malfunctioning.
7. This unit contains no user serviceable parts.
8. The FCC recommends that the AC outlet to which equipment requiring AC
power is to be installed is provided with an AC surge arrester.
Service
Type Digital Facility Interface Code Service Order Code Network Jacks
2.4 kbps Digital Interface
4.8 kbps Digital Interface
9.6 kbps Digital Interface
19.2 kbps Digital Interface
38.4 kbps Digital Interface
56 kbps Digital Interface
64 kbps Digital Interface
04DU5-24
04DU5-48
04DU5-96
04DU5-19
04DU5-38
04DU5-56
04DU5-64
6.0F
6.0F
6.0F
6.0F
6.0F
6.0F
6.0F
RJ-48S
RJ-48S
RJ-48S
RJ-48S
RJ-48S
RJ-48S
RJ-48S

viii
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruction man-
ual, may cause harmful interference to radio frequencies. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC
limits.
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard enti-
tled “Digital Apparatus," ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:
"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.
Change or modifications to this unit not expressly approved by the party re-
sponsible for compliance could void the user’s authority to operate the equip-
ment.

ix
Canadian Equipment Limitations
Notice: The Canadian Industry and Science Canada label identifies certified equip-
ment. This certification means that the equipment meets certain telecommunications
network protective, operational, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable methods of connection. In some cases, the com-
pany’s inside wiring associated with a single line individual service may be extended
by means of a certified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above limitations may not prevent degra-
dation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian mainte-
nance facility designated by the supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
The Load Number (LN) assigned to each terminal device denotes the percentage of
the total load to be connected to a telephone loop which is used by the device, to pre-
vent overloading. The termination on a loop may consist of any combination of
devices subject only to the requirement that the total of the Load Numbers of all
devices does not exceed 100.
Users should not attempt to make such connections themselves,
but should contract the appropriate electric inspection authority,
or an electrician, as appropriate.

x
ISDN Service Ordering Information for the ADTRAN DSU IV ESP with ISDN Dial
Backup
For ADTRAN DSU IV ESP ISDN applications, the following guide can be used as an
aid in ordering basic ISDN service from your local telephone company. The ADTRAN
DSU IV ESP ISDN includes NT1 and Terminal adapter functionality and supports
data rates up to 64 kbps.
Request an ISDN Basic Rate Interface (BRI) line with the following features:
• U-interface reference point
• 2BIQ line coding
• 1 B+D Service (supports up to 64 kbps)
The DSU IV ESP ISDN supports the following switch types and software proto-
cols:
• AT&T 5ESS - Custom, 5E6 and later software, National ISDN-1
• NT DMS-100 BCS-32 and later software (Pvc1), National ISDN-1 (Pvc2)
• Siemens EQSD National ISDN-1
Request that the ISDN line allocate one DYNAMIC Terminal Endpoint Identifier (TEI)
for the number
For service offered from an AT&T 5ESS, request a point-to-point line with the fol-
lowing features:
•Feature:Value
•B1Service:On Demand (DMD)
• Data Line Class: Point-to-Point
• Maximum B Channels: 1 (1B+D)
• Circuit Switched Data (CSD) Bearer Channels: Any
•NumberofCSDCalls:1 (1B+D)
•TerminalType:Type A