ADTRAN SFP+ User manual

Q
uick Star
t
The Enhanced Small Form-factor Pluggable SFP+ is a
single mode fiber optics that plugs into an ADTRAN optical
interface designed to accept SFPs. The SFP+ is an Indus-
trial Temperature (ITEMP) device that provides a single
optical interface to a physical interface, and is intended for
use with a 10 Gigabit Passive Optical Network (10G PON)
Optical Network Unit (ONU) unit. Installed into an appro-
priate ONT, the SFP+ provides a 10G XGS-PON interface
to the supporting system.
INSTALLATION
Before installing the equipment, inspect the SFP+. If
damage has occurred during shipping, file a claim with the
carrier, and then contact ADTRAN Customer Support. For
more information, refer to the warranty.
Installation Steps
To install the SFP+ into an appropriate device, complete
the following steps:
1. Insert the SFP+ into the SFP+ cage on the module.
Ensuring that the latch on the SFP+ is facing upward,
slide the SFP+ all the way into the SFP+ cage until
there is an audible “click”.
g NOTE
The latch on the SFP+ is for removal only. When removing
the SFP+, rotate the latch away from the SFP+. It should
easily slide out of the cage.
w NOTICE
Do not remove the dust cover until the optical fiber
connection is made. Ensure that you keep the dust cover
on whenever the transceiver optical fiber connector is not
inserted.
2. Continue the installation and turn-up of the host
module using the instructions in the Job Aid or Quick
Start provided with the module or other system-level
documentation available online at www.adtran.com.
SPECIFICATIONS
General
■Module Type: SFP+
■Media Type: Fiber
♦Single Mode Fiber
♦Single Fiber
■Signal Data Rate:
♦Upstream: 9.9532 Gbps
♦Downstream: 9.9532 Gbps
■Distance: 20 km
■Applications: XGS-PON ONU
■Optical Connector: SC/UPC
Optical
■Transmitter
♦Laser Diode Type: DFB
♦Transmit Central Wavelength: 1270 nm
♦Tx Output Optical Power: +4.0 dBm to +9.0 dBm
♦Tx Spectral Width: 1 nm
♦SMSR: 30 dB
♦Extinction Ratio: 6 dB
■Receiver
♦Type: CW APD/TIA
♦Input Optical Power: –28.0 dBm to –8.0 dBm
♦Receive Central Wavelength: 1577 nm
♦Receiver Sensitivity: –28.0 dBm
♦Receiver Overload: –8.0 dBm
Environmental
■Protected Equipment Severe Environment (Outdoor)
♦System Ambient Operational temperature range:
–40°C to +70°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity 5 to 95%, noncondensing
ADTRAN Pluggable Optics
SFP+
10 Gig XGS-PON ONU ITEMP
January 2020
61200488F3-13A
P/N: 1200488F3

2 61200488F3-13A
including interference that may cause undesired
operation.
■Changes or modifications not expressly approved by
ADTRAN could void the user’s authority to operate this
equipment.
■This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
♦Reorient or relocate the receiving antenna.
♦Increase the separation between the equipment and
receiver.
♦Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
♦Consult the dealer or an experienced radio/TV
technician for help.
■CAN ICES-3(B)/NMB-3(B)
■This product is designed to meet the following
environmental classes:
♦ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental
conditions; Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental
conditions; Stationary use at weather-protected
locations,” Class 3.4
■The equipment is designed to function without
degradation during exposure to all test severities per
Class 3.4.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/
WEEE.
SAFETY AND REGULATORY
ENGLISH
f WARNING!
Read all warnings, cautions, notes and installation
instructions before installing or servicing this equipment.
C CAUTION!
This product contains a Class 1 Laser that complies with
FDA 21 CFR 1040.10, 1040.11 and 60825-1.
f CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing
material when transporting or storing. When working on
modules, always place them on an approved antistatic
mat that is electrically grounded.
■This product and the host system are designed and
intended for installation as part of a Common Bonding
Network (CBN).
■This product’s outer case may not be “electrically
isolated” from other circuits. As a result, this product can
only be used is systems that are installed in a DC-C
(common) configuration.
■If the host system has a protective earth (PE) terminal,
the PE terminal of the host system must be connected to
protective earth (PE) to ensure that the exposed metal
(i.e., front panels, optical modules) on the product is
properly grounded.
g NOTE
■This product is NRTL listed to the applicable UL
Standards.
■The product is designed to meet the applicable
requirements of Telcorida GR-3108-CORE and GR-
1089-CORE. This product has also been evaluated to
applicable international standards and meets the
requirements of CE marking.
■This product is intended for deployment in locations
such as business, residential, outside plant cabinets,
and inside remote DSLAMs and DPUs. This product is
to be installed and serviced by trained and qualified
Service Personnel only.
■This product is designed to be deployed in GR-3108-
CORE environmental Class 1, 2 or 3.
■This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: 1.
This device may not cause harmful interference, and (2)
this device must accept any interference received,

61200488F3-13A 3
FRANÇAIS
f WARNUNG!
Lisez toutes les mentions de danger et de prudence et les
remarques, ainsi que la notice d'installation, avant
d'effectuer l'installation ou l'entretien de cet équipement.
C ATTENTION!
Ce produit est un laser de classe 1 conforme à la norme
FDA 21 CFR 1040.10 et 1040.11 et 60825-1.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des
modules, portez un bracelet de décharge antistatique
pour éviter d’endommager les composants
électroniques. Placez les modules dans un emballage
antistatique lors du transport ou du stockage. Lorsque
vous travaillez sur les modules, placez-les toujours sur
un tapis antistatique certifié muni d’un branchement de
mise à la terre.
■Ce produit et le système hôte sont conçus et destinés à
être installés dans le cadre d'un réseau Bonding
commun (CBN).
■Le boîtier extérieur de ce produit pourrait ne pas être
“isolé galvaniquement” des autres circuits. Donc ce
produit peut être utilisé uniquement dans des systèmes
dotés d’une configuration de retour commun
d’alimentation en courant continu (c.c.-C).
■Si le système hôte est doté d’une borne de mise à la
terre de protection (PE), la borne PE du système hôte
doit être connectée à la mise à terre de protection (PE),
afin d’assurer que les parties métaliques à découvert
(panneaux frontaux, modules optiques) du produit soient
correctement mis à terre.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples
renseignements sur RoHS/WEEE.
DEUTSCH
f WARNUNG!
Lesen Sie alle Warnungen, Gefahrenhinweise,
Anmerkungen und Installationsanweisungen bevor Sie
dieses Gerät installieren oder warten.
C VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser, die mit FDA 21 CFR
1040.10 und 1040.11 und 60825-1 entspricht.
f VORSICHT!
■Elektrostatische Entladung können elektronische
Module beschädigen. Tragen Sie beim Umgang mit
Modulen ein Erdungsarmband, um Schäden an den
elektronischen Komponenten zu vermeiden.
Transportieren oder lagern Sie Module in antistatischem
Verpackungsmaterial. Bei der Arbeit an den Modulen,
achten Sie darauf, diese stets auf antistatische,
elektrisch geerdete Matten zu legen.
■Dieses Produkt und das Host-System entworfen und für
die Installation als Teil einer gemeinsamen Bonding
Network (CBN) vorgesehen.
■Das äußere Gehäuse dieses Produktes mag nicht von
anderen Stromkreisen “elektrisch isoliert” sein. Deshalb
kann dieses Produkt nur in Systemen verwendet
werden, die in einer gemeinsamen Gleichstrom-
Rücklauf-Konfiguration installiert sind.
■Falls das Host-System über einen Schutzleiteranschluss
(PE) verfügt, muss der PE-Anschluss des Host-Systems
mit dem Schutzleiteranschluss (PE) verbunden werden,
um sicherzustellen, dass das freiliegende Metall (d. h.
Frontblenden, Optikmodule) am Produkt
ordnungsgemäß geerdet ist.
g HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte
besuchen. Sie www.adtran.com für ausführlichere Informa-
tionen zu RoHS/WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2020 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61200488F3-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)