ADTRAN IQ Probe 1200214L1 User manual

61200214L1-1A
August 1998
IQ Probe
Frame Relay
Monitoring Probe
USER MANUAL
IQ Probe Unit 1200214L1
ESP 4-wire SW56 DBU Card 1204001L1
ESP V.34 DBU Card 1204002L1
ESP ISDN DBU Card 1204004L1
ESP External DCE Card 1204006L1

Trademark Information:
OpenView is a registered trademark of Hewlett-Packard Company.
SunNet Manager is a registered trademark of Sun Microsystems, Inc.
Netview is a registered trademark of IBM.
IQ View is a trademark of ADTRAN, Inc.
This product includes software developed by the University of California, Berkeley,
and its contributors.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
© 1998 ADTRAN, Inc.
All rights reserved.
Printed in USA.

ABOUT THIS MANUAL
This manual is arranged so you can quickly and easily find the
information you need. The following is an overview of the
contents of this manual:
• Chapter 1, Introduction, familiarizes you with frame relay
networks and IQ Probe highlights.
• Chapter 2, Installation, describes the IQ Probe connectors (pin
assignments are given in Appendix A) and provides an
installation diagram.
• Chapter 3, Operation, explains how to operate your IQ Probe
using either the front panel or a terminal interface.
• Chapter 4, Applications, provides examples of some common
IQ Probe applications. This chapter includes network dia-
grams as well as configuration examples.
• Chapter 5, Configuration Overview, explains how to access the
IQ Probe configuration menu and provides menu trees for
both the front panel and the terminal interface.
• Chapters 6 through 9 provide brief explanations for selections
made in the Configuration menus. These chapters are based
on the first level menu branches of the Configuration menu:
DTE Port, DCE Port, Dial Backup, and System Configuration.
• Chapter 10, Statistics, describes how to access statistical
information from the IQ Probe.
• Chapter 11, Testing, explains how to access the IQ Probe
diagnostic features, including PVC loopback and ping tests.
• Chapter 12, Activating Dial Backup Options, provides infor-
mation on the dialing options accessed through the Main
menu.
• Appendix A provides pinouts for the IQ Probe connectors.
• Appendix B contains product specifications.

Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Whenusingyourtelephoneequipment,pleasefollowthesebasicsafetyprecautions
to reduce the risk of fire, electrical shock, or personal injury:
1. Do not use this product near water, such as near a bath tub, wash bowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
2. Avoidusingatelephone(otherthanacordless-type)duringanelectricalstorm.
There is a remote risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the
manual. Do not dispose of batteries in a fire. They may explode. Check with
local codes for special disposal instructions.

FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of the FCC rules. On the bottom of the ESP DBU card is
a label that shows the FCC registration number and ringer equivalence number (REN) for this
equipment. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given
as soon as possible. The telephone company will advise the customer of the right to file a
complaint with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the proper operation of this equipment; advance notification and
the opportunity to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and
warranty information. The telephone company may require this equipment to be
disconnected from the network until the problem is corrected, or it is certain the equipment is
not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This
equipment is designed to be connected to the telephone network or premises wiring using an
FCC compatible modular jack, which is Part 68 compliant.
7. The following information may be required when applying to the local telephone company for
dial backup service:
Service Type REN/SOC FIC USOC
56 kbps Digital Interface 6.0F 04DU5-56 RJ-48S
64 kbps Digital Interface 6.0F 04DU5-64 RJ-48S
Loop Start (V.34) 0.8B/0.4A 02LS2 RJ-11C
8. The REN is useful in determining the quantity of devices you may connect to your telephone
line and still have all of those devices ring when your number is called. In most areas, the sum
of the RENs of all devices should not exceed five. To be certain of the number of devices you
may connect to your line as determined by the REN, call your telephone company to
determine the maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company.
Connection to party lines is subject to state tariffs. (Contact your state public utility
commission or corporation commission for information.)

FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference
whentheequipmentisoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.
Change or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard
entitled "Digital Apparatus," ICES-003 of the Department of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:
"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

CANADIAN EQUIPMENT LIMITATIONS
Notice: The Canadian Industry and Science Canada label identifies certified
equipment. This certification means that the equipment meets certain telecom-
munications network protective, operational, and safety requirements. The
Department does not guarantee the equipment will operate to the user's satisfac-
tion.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equip-
ment must also be installed using an acceptable method of connection. In some
cases, the company's inside wiring associated with a single line individual
service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the telecom-
munications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connec-
tions of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or an
electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage
of the total load to be connected to a telephone loop which is used by the device,
to prevent overloading. The termination on a loop may consist of any combina-
tion of devices subject only to the requirement that the total of the Load Num-
bers of all devices does not exceed 100.

ISDN Service Ordering Information for the ADTRAN IQ Probe With ISDN Dial
Backup
For ADTRAN IQ Probe ISDN dial backup applications, the following guide can be
used as an aid in ordering basic ISDN service from your local telephone company.
TheADTRANIQProbe ISDNincludesNT1andTerminaladapter functionalityand
supports data rates up to 128 kbps.
Request an ISDN Basic Rate Interface (BRI) line with the following features:
U-interface reference point
2B1Q line coding
1B+D Service (supports up to 64 kbps)
2B+D Service (supports up to 128 kbps)
The IQ Probe ISDN supports the following switch types and software protocols:
Lucent 5ESS Custom, 5E6 and later software, National ISDN-1
NT1 DMS-100 BCS-32 and later software (Pvc1), National ISDN-1 (Pvc2)
Siemens EWSD National ISDN-1
Request that the ISDN line allocate one DYNAMIC Terminal Endpoint Identifier
(TEI) for the number.
For service offered from an Lucent 5ESS, request a point-to-point line with the
following features:
Feature: Value
B1 Service: On Demand (DMD)
Data Line Class: Point-to-Point
Maximum B Channels: 1 (1B+D) or 2 (2B+D)
Circuit Switched Data (CSD) Bearer Channels: Any
Number of CSD Calls: 1 (1B+D) or 2 (2B+D)
Terminal Type: Type A

Turn the Following Features Off:
Packet Mode Data
Multi-line Hunt
Multiple Call Appearances
Electronic Key Telephone Sets (EKTS)
Shared Dictionary Numbers
Accept Special Type of Number
Intercom Groups
Network Resource Selector (Modem Pools)
Message Waiting
Hunting
InterLata Competition
For service offered from a Northern Telecom DMS-100, request a Point-to-Point
Multi-Point line with the following features:
Line Type: Basic Rate, Functional
Electronic Key Telephone Sets (EKTS): No
Call Appearance Handling (CACH): No
Non-Initializing Terminal: No
Circuit Switched Service: Yes
Packet Switched Service: No
TEI: Dynamic
Bearer Service: Circuit Switched voice and data permitted on any B channel (packet mode
data not permitted)

Table of Contents