261445505F4C-13A
the SFP is being deployed in is not designed nor intended for
installation as part of an Isolated Bonding Network (IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (i.e., front
panels, SFP/XFP modules) on the product is properly
grounded by way of the backplane connector.
■The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■This product is designed to be deployed in GR-3108-CORE
environmental class 1.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has also been evaluated to international safety
standards EN 62368-1, AS/NZS 62368.1, and IEC 62368-1.
This product meets the requirements for CE marking under the
EMC Directive and Low Voltage Directive. Standards used to
demonstrate Compliance are EN 300 386 and EN 62368.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by Adtran
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental condi-
tions; Storage Class” 1.2
♦ETSI EN 300 019-2-2 “Classification of environmental condi-
tions, Transportation”, Class 2.3
♦ETSI EN 300 019-2-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations”, Class
3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-1-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
■Receiver
♦Rx Type: APD/TIA
♦Rx Wavelengths:
●Lane –1: 1264.5 to 1277.5 nm (Typical: 1271 nm)
●Lane –2: 1284.5 to 1297.5 nm (Typical: 1291 nm)
●Lane –3: 1304.5 to 1317.5 nm (Typical: 1311 nm)
●Lane –4: 1324.5 to 1337.5 nm (Typical: 1331 nm)
♦Rx Output Optical Power: –18.6 dBm to –4.5 dBm per lane
♦Receiver Overload: –4.5 dBm
♦Receiver Sensitivity: –19 dBm
Environmental
■Controlled Protected Environment (Indoor) (CTEMP)
■System Ambient Operational temperature
range: –5°C to +50°C
■Storage temperature range: –40°C to +85°C
■Relative humidity: 5 to 95%, non-condensing
SAFETY AND REGULATORY
English
Read all warnings and cautions before installing or servicing this
equipment.
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10 and 1040.11 and IEC 60825-1. This product is
NRTL Listed and CB Certified to all applicable American and
European safety standards. For continued compliance with the
above standards, install only Adtran-approved Class 1 Laser
Modules in Adtran products.Adtran cannot certify system integrity
with other laser modules.
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■The SFP meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. The
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises.
■Per GR-1089-CORE the Adtran system that the SFP is being
deployed in is designed and intended for installation as part of
a Common Bonding Network (CBN). The Adtran system that
