Advantech ECU-P1522LPE Installation and operation manual

ECU-P1522LPE Startup Manual 1
Before installation, please make sure that you have re-
ceived the following:
• ECU-P1522LPE card
• Quick Start User Manual
If anything is missing or damaged, contact your distributor
or sales representative immediately.
For more detailed information on this product, please refer
to the ECU-P1522LPE User Manual on the Website (PDF
format).
FCC Class A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio com-
munications. Operation of this equipment in a residential
area is likely to cause interference in which case the user is
required to correct interference at his own expense.
CE
This product has passed the CE test for environmental
specicationswhenshieldedcablesareusedforexternal
wiring. We recommend the use of shielded cables. This kind
of cable is available from Advantech. Please contact your
local supplier for ordering information.
ECU-P1522LPE 2-Port SFP HSR/PRP Card with Low
Prole PCI Express
Startup Manual
The ECU-P1522LPE is a standard PCIE extension card
with HSR/PRP functions to reduce data transfer packet loss
probability and ensure seamless switching.
• TheECU-P1522LPEsupportsfollowingspecications:
• 2 port SFP Base Ethernet Card with HSR/PRP
• Supports HSR Protocol (IEC 62439-3 Clause 5)
• Supports PRP Protocol (IEC 62439-3 Clause 4)
• BUS Type: PCI-Express x1 Gen 1
• Dimensions: 68.9 x 181 x 20.32 mm
• Power Consumption: 12V ±5% @ 500mA typical;
3.3V ±5% @ 600mA typical;
• Operating Temp: -25 ~ 70°C (-13 ~158°F)
• Operating Humidity: 10 ~ 90% RH non-condensing (refer
to IEC 60068-2-3)
After the device driver is installed, you can now install the
ECU-P1522LPE card in your computer.
Please follow the steps below to install the ECU-P1522LPE
card:
1. Turno󰀨yourcomputerandunplugthepowercordand
cables. TURN OFF your computer before installing or
removing any components on the computer.
2. Remove the cover of your computer.
3. Remove the slot cover on the back panel of your
computer.
4. Touch the metal part on the surface of your computer
to neutralize the static electricity that might be on your
body.
5. Insert the ECU-P1522LPE card into a PCI Express
slot. Hold the card only by its edges and carefully align
itwiththeslot.Insertthecardrmlyintoplace.Useof
excessive force must be avoided; otherwise, the card
might be damaged.
6. Fasten the bracket of the PCI Express card on the back
panel rail of the computer with screws.
7. Connect SFP modules to the SFP ports.
8. Replace the cover of your computer chassis.
9. Plug in the power cord and turn on the computer.
OverviewPacking List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com/eAutomation
For technical support and service:
http://www.advantech.com/support/
This startup manual is for ECU-P1522LPE.
Part No.
Printed in China
1st Edition
August 2023
Declaration of Conformity
Hardware Installation
Specications

2 ECU-P1522LPE Startup Manual
Name Function Interface
A RedBox_A
100M Base-FX SFP Interface
(Select by SFP MODE)
1000M Base-X SFP Interface
(Select by SFP MODE)
B RedBox_B
100M Base-FX SFP Interface
(Select by SFP MODE)
1000M Base-X SFP Interface
(Select by SFP MODE)
InterLink RedBox_
Interlink 10/100/1000 Mbps Base-T
Name Function Interface
A_ACT Blinking SFP module A transmit data
A_Link
Yellow 100M Base-FX SFP_A is
linked
Green 1000M Base-X SFP_A is
linked
B_ACT Blinking SFP module B transmit data
B_Link
Yellow 100M Base-FX SFP_B is
linked
Green 1000M Base-X SFP_B is
linked
Mode_1
HSR/PRP
mode
No light Normal switch
Green HSR
Yellow PRP
Mode_2
SFP mode
Yellow 100M Base-FX SFP
Green 1000M Base-X SFP
Intel link
Blink(Green) Interlink port transmit data
Yellow Interlink port 100M linked
Green Interlink port 1000M linked
Connector and LED Assignments
Switch Mode SW1
Normal Switch OFF OFF OFF OFF
HSR OFF ON OFF OFF
PRP ON ON OFF OFF
SFP Mode SW2
1000M Base-FX
100M Base-FX
NC
Switch and Jumper Settings