Advantech SOM-7583 User manual

User Manual
SOM-7583
CPU Computer on Module

SOM-7583 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2021
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
AMD are trademarks of AMD Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2006758300 Edition 1
Printed in Taiwan November 2021

iii SOM-7583 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
FM
This equipment has passed FM certification. According to the National Fire Protec-
tion Association, work sites are categorized into different classes, divisions, and
groups based on hazard considerations. This equipment is compliant with the specifi-
cations for Class I, Division 2, Groups A, B, C, and D indoor hazards.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

SOM-7583 User Manual iv
Warnings, Cautions, and Notes
Document Feedback
To assist us with improving this manual, we welcome all comments and constructive
criticism. Please send all feedback in writing to [email protected].
Safety Precautions - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from the PC chassis
before manual handling. Do not touch any components on the CPU card or
other cards while the PC is powered on.
Disconnect the power before making any configuration changes. A sudden rush
of power after connecting a jumper or installing a card may damage sensitive
electronic components.
Warning! Warnings indicate conditions that could cause personal injury if not
observed!
Caution! Cautions are included to help prevent hardware damage and data loss.
For example,
“Batteries are at risk of exploding if incorrectly installed. Do not attempt
to recharge, force open, or heat the battery. Replace the battery only
with the same or equivalent type as recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.”
Note! Notes provide additional and/or optional information.

v SOM-7583 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following occurs, have the equipment checked by service person-
nel:
–The power cord or plug is damaged.
–Liquid has penetrated the equipment.
–The equipment has been exposed to moisture.
–The equipment is malfunctioning, or does not operate according to the user
manual.
–The equipment has been dropped and damaged.
–The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -20 °C (-4 °F) or above 60 °C (140 °F) as this may damage the compo-
nents. The equipment should be kept in a controlled environment.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at
the operator’s position does not exceed 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

SOM-7583 User Manual vi

vii SOM-7583 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Functional Block Diagram ......................................................................... 4
1.3 Product Specifications............................................................................... 5
1.3.1 Compliance ................................................................................... 5
1.3.2 Feature List ................................................................................... 5
1.3.3 Processor System......................................................................... 6
1.3.4 Graphics/Audio ............................................................................. 6
1.3.5 Expansion Interfaces .................................................................... 6
1.3.6 Serial Bus...................................................................................... 7
1.3.7 I/O ................................................................................................. 7
1.3.8 Power Management...................................................................... 8
1.3.9 Environment.................................................................................. 9
1.3.10 MTBF ............................................................................................ 9
1.3.11 OS Support ................................................................................... 9
1.3.12 Advantech iManager ................................................................... 10
1.3.13 Power Consumption.................................................................... 10
1.3.14 Performance ............................................................................... 10
1.3.15 Selection Guide w/P/N ................................................................ 11
1.3.16 Packing list.................................................................................. 11
1.3.17 Development Board .................................................................... 11
1.3.18 Optional Accessory ..................................................................... 11
1.3.19 Pin Description............................................................................ 11
Chapter 2 Mechanical Information ....................13
2.1 Board Information.................................................................................... 14
Figure 2.1 Board Chip Identification – Front .............................. 14
Figure 2.2 Board Chip Identification – Rear............................... 14
2.1.1 Connector List............................................................................. 15
Table 2.1: FAN1 Fan ................................................................. 15
2.2 Mechanical Drawing................................................................................ 15
Figure 2.3 Board Mechanical Diagram - Front........................... 15
Figure 2.4 Board Mechanical Diagram - Rear ........................... 16
Figure 2.5 Board Mechanical Diagram - Side............................ 16
2.3 Assembly Drawing .................................................................................. 17
Figure 2.6 Assembly Diagram ................................................... 17
2.4 Assembly Diagram.................................................................................. 18
Figure 2.7 10 TGL-UP3 4C Height and Tolerance Diagram...... 18
Chapter 3 AMI BIOS ............................................19
3.1 Introduction ............................................................................................. 20
Figure 3.1 Setup Program Initial Screen.................................... 20
3.2 Entering Setup ........................................................................................ 21
3.3 Main Setup.............................................................................................. 21
Figure 3.2 Main Setup Screen ................................................... 21
3.4 Advanced BIOS Features Setup............................................................. 22
Figure 3.3 Advanced BIOS Features Setup Screen .................. 22
3.4.1 RC ACPI Settings ....................................................................... 23
Figure 3.4 RC ACPI Settings ..................................................... 23
3.4.2 CPU Configuration ...................................................................... 24
Figure 3.5 CPU Configuration_1................................................ 24

SOM-7583 User Manual viii
Figure 3.6 Active Processor Core Setting ................................. 25
3.4.3 Power & Performance................................................................. 26
Figure 3.7 Power & Performance .............................................. 26
Figure 3.8 CPU- Power Management Control........................... 27
Figure 3.9 Configurable TDP Boot Mode .................................. 28
Figure 3.10ConfigTDP Turbo Activation Ratio ........................... 28
Figure 3.11GT- Power Management Control ............................. 29
3.4.4 PCH-FW Configuration ............................................................... 30
Figure 3.12PCH-FW Configuration............................................. 30
Figure 3.13Firmware Update Configuration ............................... 31
3.4.5 Trusted Computing ..................................................................... 31
Figure 3.14Trusted Computing................................................... 31
3.4.6 ACPI Settings ............................................................................. 32
Figure 3.15ACPI Settings ........................................................... 32
3.4.7 Embedded Controller.................................................................. 33
Figure 3.16Embedded Controller ............................................... 33
Figure 3.17Serial Port 1 Configurations ..................................... 34
Figure 3.18Serial Port 2 Configurations ..................................... 35
Figure 3.19Hardware Monitor..................................................... 36
3.4.8 Serial Port Console Redirection.................................................. 36
Figure 3.20Serial Port Console Redirection ............................... 36
Figure 3.21Terminal Type Settings ............................................ 37
Figure 3.22Terminal Type Settings ............................................ 37
Figure 3.23Data Bits Settings..................................................... 38
Figure 3.24Parity Settings .......................................................... 38
Figure 3.25Stop Bits Settings ..................................................... 39
Figure 3.26Flow Control Settings ............................................... 39
Figure 3.27Putty KeyPad Settings.............................................. 40
3.4.9 USB Configuration ...................................................................... 41
Figure 3.28USB Configuration.................................................... 41
Figure 3.29USB Transfer Time-out Settings .............................. 42
Figure 3.30Device Power-up Delay Settings.............................. 42
3.4.10 Network Stack Configuration ...................................................... 43
Figure 3.31Network Stack Configuration.................................... 43
Figure 3.32 Network Stack Configuration Settings..................... 43
3.5 Chipset Setting........................................................................................ 44
Figure 3.33Chipset Setup........................................................... 44
3.5.1 System Agent (SA) Configuration............................................... 45
Figure 3.34System Agent (SA) Configuration ............................ 45
Figure 3.35Memory Configuration .............................................. 46
Figure 3.36Graphics Configuration............................................. 46
Figure 3.37Primary Display ........................................................ 47
Figure 3.38Internal Graphics Settings ........................................ 47
Figure 3.39GTT Size Settings .................................................... 48
Figure 3.40Aperture Size Settings.............................................. 48
Figure 3.41DVMT Pre-Allocated Settings................................... 49
Figure 3.42DVMT Toal Gfx Mem Settings.................................. 49
3.5.2 PCH-IO Configuration................................................................. 50
Figure 3.43PCH-IO Configuration .............................................. 50
Figure 3.44PCI Express Configuration ....................................... 51
Figure 3.45PCI Express Root Port 0 Configuration.................... 52
Figure 3.46SATA And RST Configuration .................................. 53
Figure 3.47Security Configuration Settings ................................ 54
Figure 3.48HD Audio Configuration............................................ 55
Figure 3.49Security Configuration Settings ................................ 56
Figure 3.50Serial IO Configuration Settings ............................... 57
3.5.3 Security Settings......................................................................... 58
Figure 3.51Security Setup .......................................................... 58
3.5.4 Boot Settings .............................................................................. 59
Figure 3.52Security Setup .......................................................... 59

ix SOM-7583 User Manual
3.5.5 Save & Exit ................................................................................. 60
Figure 3.53Security Setup .......................................................... 60
Chapter 4 S/W Introduction and Installation ....61
4.1 S/W Introduction...................................................................................... 62
4.2 Driver Installation .................................................................................... 62
4.2.1 Windows Driver Setup ................................................................ 62
4.2.2 Other OS..................................................................................... 62
4.3 Advantech iManager ............................................................................... 63
Appendix A Pin Assignment .................................65
A.1 SOM-7583 Type 10 Pin Assignment....................................................... 66
Appendix B Watchdog Timer ................................69
B.1 Programming the Watchdog Timer ......................................................... 70
Appendix C Programming GPIO ...........................71
C.1 GPIO Register......................................................................................... 72
Appendix D System Assignments ........................73
D.1 System I/O Ports ..................................................................................... 74
Table D.1: System I/O ports....................................................... 74
D.2 Interrupt Assignments ............................................................................. 75
Table D.2: Interrupt Assignments............................................... 75
D.3 1st MB Memory Map............................................................................... 75
Table D.3: 1st MB Memory Map ................................................ 75

SOM-7583 User Manual x

Chapter 1
1General Information
This chapter details background
information on the SOM-7583 CPU
Computer on Module.
Sections include:
Introduction
Functional Block Diagram
Product Specification

SOM-7583 User Manual 2
1.1 Introduction
Advantech’s SOM-7583 series features 11th Generation Intel® Core™/Celeron pro-
cessors that leverage 14nm process technology. This solution supports LPDDR4x
4266MT/s with 1.1V power design, and up to 16GB memory down. In addition, SOM-
7583 augments memory capacity configuration via an i7-1185G7E SKU upgrade to
quad-core. SOM-7583 further provides super speed I/O technology such as
2.5Gbase-T TSN LAN, PCIe Gen 4, and USB 3.2 Gen 2.
This solution also integrates 11th Gen. Intel® Core™ processors Iris® Xe Graphics to
empower up to 4 x independent 4K displays or 2 x 8K HDR ports.
This device features Advantech’s iManager (SUSI4). This software meets embedded
application requirements by providing a multi-level watchdog timer, voltage and tem-
perature monitoring, thermal protection, and mitigation via processor throttling, LCD
backlight on/off and brightness control, and embedded storage for customized infor-
mation. When combined with Advantech WISE-DeviceOn, it can remotely monitor
and control devices.

3 SOM-7583 User Manual
Chapter 1 General Information
Acronyms
Term Define
AC’97 Audio CODEC (Coder-Decoder)
ACPI Advanced Configuration Power Interface – standard to implement power sav-
ing modes in PC-AT systems
BIOS Basic Input Output System – firmware in PC-AT system that is used to initialize
system components before handing control over to the operating system
CAN
Controller-area network (CAN or CAN-bus) is a vehicle bus standard designed
to allow microcontrollers to communicate with each other within a vehicle with-
out a host computer
DDI Digital Display Interface – containing DisplayPort, HDMI/DVI, and SDVO
EAPI
Embedded Application Programmable Interface
Software interface for COM Express® specific industrial function
System information
Watchdog timer
I2C Bus
Flat Panel brightness control
User storage area
GPIO
GbE Gigabit Ethernet
GPIO General purpose input output
HDA
Intel High Definition Audio (HD Audio) refers to the specification released by
Intel in 2004 for delivering high definition audio that is capable of playing back
more channels at higher quality than AC’97
I2C
Inter Integrated Circuit – 2 wire (clock and data) signaling scheme allowing
communication between integrated circuit, primarily used to read and load reg-
ister values
ME Management Engine
PC-AT “Personal Computer – Advanced Technology” – an IBM trademark term used
to refer to Intel based personal computer in 1990s
PEG PCI Express Graphics
RTC Real Time Clock – battery backed circuit in PC-AT systems that keeps system
time and date as well as certain system setup parameters
SPD Serial Presence Detect – refers to serial EEPROM on DRAMs that has DRAM
Module configuration information
TPM Trusted Platform Module, chip to enhance the security features of a computer
system
UEFI Unified Extensible Firmware Interface
WDT Watchdog Timer

SOM-7583 User Manual 4
1.2 Functional Block Diagram

5 SOM-7583 User Manual
Chapter 1 General Information
1.3 Product Specifications
1.3.1 Compliance
PICMG COM.0 (COM Express) Revision 3.0
Compact Size – 55 x 84 mm (2.1 x 3.3 in)
Pin-out Type 10 compatible
1.3.2 Feature List
Feature
Type
Connector
Row Feature
Type 10 Define
SOM-7583
Max. Min.
Display A-B eDP (muxed on LVDS Channel A) 1 0 1
A-B Digital Display Interfaces 0 1 0 1
Expansion A-B PCI Express x1 4 1 4
A-B LPC 1 1 1
Serial
A-B SMBus 1 1 1
A-B I2C Bus 1 1 1
A-B Serial Port 2 0 2
A-B CAN Bus (muxed on SER1) 1 0 1
I/O
A-B LAN Port 0 (Gigabit Ethernet) 1 1 1
A-B SATA 2 1 2
A-B USB2.0 8 4 8
A-B USB Client 1 0 0
A-B HD Audio 1 0 1
A-B SPI Bus 2 1 1
A-B General Purpose I/O (GPIO) 8 8 8
A-B SDIO (muxed on GPIO) 1 0 0
A-B Watchdog Timer Output 1 0 1
A-B Speaker Out 1 1 1
A-B Carrier Board BIOS Flash Support 1 0 1
A-B Power Button Support 1 1 1
A-B Power Good 1 1 1
A-B VCC_5V_SBY Contacts 4 4 4
A-B Sleep 1 0 1
A-B Thermal Protection 1 0 1
A-B Lid Input 1 0 1
A-B Battery Low Alarm 1 0 1
A-B Suspend/Wake Signals 3 0 3
A-B Fan PWM/Tachometer 2 0 2
A-B Trusted Platform Modules 1 0 1
A-B USB 3.0 (Gen2, 10Gbps) 2 0 2

SOM-7583 User Manual 6
1.3.3 Processor System
*TDP can be configured up to 28W or down to 12W.
1.3.4 Graphics/Audio
Iris® Xe Graphics uses high-performance, low-power HW acceleration for video
decoding operations for multiple video codecs.
The HW encode is exposed by the graphics driver using the following APIs:
Intel Media SDK
MFT (Media Foundation Transform) filters
Iris® Xe Graphics supports full HW accelerated video encoding for AVC/MPEG2/
HEVC/VP8/JPEG.
Dual Display: DDI/eDP
1.3.5 Expansion Interfaces
1.3.5.1 LPC
Supports Low Pin Count (LPC) 1.1 specifications without DMA or bus mastering.
Enables connection to super I/O, embedded controllers, or TPM. LPC clock is
24MHz.
CPU Std. Freq. Max. Turbo Freq. Core Cache (MB) TDP(W)
i7-1185G7E 1.8GHz 4.4GHz 4 12 15*
i5-1145G7E 1.5GHz 4.1GHz 4 8 15*
i3-1115G4E 2.2GHz 3.9Ghz 2 6 15*
Celeron® 6305E 1.8GHz N/A 2 4 15
i7-1185GRE 1.8GHz 4.4GHz 4 12 15*
i5-1145GRE 1.5GHz 4.1GHz 4 8 15*
i3-1115GRE 2.2GHz 3.9Ghz 2 6 15*
CPU Graphic Core Base Freq. Max Freq.
i7-1185G7E Iris® Xe Graphics 1.8GHz 4.4GHz
i5-1145G7E Iris® Xe Graphics 1.5GHz 4.1GHz
i3-1115G4E Iris® Xe Graphics 2.2GHz 3.9GHz
Celeron® 6305E Intel® UHD Graphics 1.8GHz N/A
i7-1185GRE Iris® Xe Graphics 1.8GHz 4.4GHz
i5-1145GRE Iris® Xe Graphics 1.5GHz 4.1GHz
i3-1115GRE Intel® UHD Graphics 2.2GHz 3.9GHz

7 SOM-7583 User Manual
Chapter 1 General Information
1.3.6 Serial Bus
1.3.6.1 SMBus
Supports SMBus 2.0 specifications with alert pin.
1.3.6.2 I2C Bus
Supports I2C bus 7-bit and 10-bit address modes at both 100KHz and 400KHz.
1.3.7 I/O
1.3.7.1 Gigabit Ethernet
Ethernet: Intel I225IT Gigabit LAN supports 10/100/1000/2.5G Mbps Speed.
1.3.7.2 SATA
Supports up to 2 x ports SATA Gen3 (6.0 Gb/s), backward compliant to SATA Gen2
(3.0 Gb/s) and Gen1 (1.5 Gb/s). Maximum data rate is 600 MB/s. Supports AHCI 1.3
and 1.3.1 mode.
1.3.7.3 USB 3.2 Gen2/USB 2.0
SOM-7583 supports 2 x ports USB 3.2 Gen2 (10 Gbps) and 8 x ports USB 2.0 (480
Mbps). These are backward compatible to USB1.x. For USB 3.1 this solution sup-
ports LPM (U0, U1, U2, and U3) manageability to conserve power.
Notice: To meet USB 3.2 Gen 2 performance, we strongly recommend to use of a
certified cable.
1.3.7.4 USB 3.1
1.3.7.5 USB2.0
1.3.7.6 SPI Bus
Supports BIOS flash only. SPI clock can be 50MHz; with capacity up to 32MB.
1.3.7.7 GPIO
8 x programmable general purpose input or output (GPIO).
1.3.7.8 Watchdog
Supports multi-level watchdog time-out output. Provides 1-65535 level, from 100 mil-
liseconds to 109.22 minutes interval.
Type 10 P0 P1
SoC P0 P1
Type 10 OC_01
SoC USB_OC# OC_0
Type 10 P0 P1 P2 P3 P4 P5 P6 P7
SoC P0 P1 P2 P3 P4 P5 P6 P7
Type 10 OC_01 OC_23 OC_45 OC_67
SoC USB_OC# OC_0 OC_1 OC_2 OC_3

SOM-7583 User Manual 8
1.3.7.9 Serial port
2 x wire serial port (Tx/Rx) and support 16550 UART compliance:
Programmable FIFO or character mode
16-byte FIFO buffer on transmitter and receiver in FIFO mode
Programmable serial-interface characteristics: 5, 6, 7, or 8-bit character
Even, odd, or no parity bit selectable
1, 1.5, or 2 stop bit selectable
Baud rate up to 115.2K
1.3.7.10 TPM
Support TPM 2.0 module by default.
1.3.7.11 Smart Fan
Support 2 x Fan PWM control signal and 2 x tachometer inputs for fan speed detec-
tion. Provides 1 x on module with connector and 1 x on carrier board followed by
PICMG COM Express R3.0 specification.
1.3.7.12 BIOS
There is a BIOS chip on the module by default. Users can place BIOS chip on a car-
rier board with appropriate design and jumper setting on BIOS_DIS#[1:0].
Notice: We recommend going to the BIOS setup menu and loading the default set-
tings during the first boot up if the system COMS are cleared.
1.3.8 Power Management
1.3.8.1 Power Supply
Supports both ATX and AT power modes. The VSB is for suspend power and is
optional if not required by standby (suspend-to-RAM) support. The RTC Battery is
optional if keeping time and date is not required.
VCC: 8.5V ~ 20V
VSB: 4.75V ~ 5.25V (Suspend power)
RTC Battery Power: 2.0 ~ 3.3V
1.3.8.2 PWROK
Power OK (PWROK) is from the main power supply. A high value indicates sufficient
power. This signal can be used to delay module startup in order to program the time
of carrier based FPGAs or other configurable devices.
1.3.8.3 Power Sequence
According to PICMG COM Express R3.0 specifications.
BIOS_DIS0# BIOS_DIS#1 Boot up destination/function
Open Open Boot from Module’s SPI BIOS
Open GND SPI_CS0# to Carrier Board, SPI_CS1# to Module
GND GND SPI_CS0# to Module, SPI_CS1# to Carrier Board

9 SOM-7583 User Manual
Chapter 1 General Information
1.3.8.4 Wake Event
Diverse wake-up event support allows users to apply the solution to different scenar-
ios:
Wake-on-LAN(WOL): Wake to S0 from S3/S4/S5
USB Wake: Wake to S0 from S3/S4
PCIe Device Wake: According to user inquiry and possible BIOS customization
LPC Wake: According to user inquiry and possible BIOS customization
1.3.8.5 Advantech S5 ECO Mode (Deep Sleep Mode)
Advantech iManager features a mechanism that enables the system to enter a very
low suspend power mode, or “S5 ECO mode”. In this mode, the module will cut
power — including suspend and active power — and keep an on-module controller
active. In this mode, the device will only consume 50mW to enable a longer battery
pack lifespan. This mode is enabled using BIOS. In this mode, the system (or mod-
ule) needs to use the power button to boot up.
1.3.9 Environment
1.3.9.1 Temperature
Operating: 0 ~ 60 °C (32 ~ 140 °F), with an active heat sink under 0.7m/s air
flow chamber
Storage: -40 ~ 85 °C (-40 ~ 185 °F)
1.3.9.2 Humidity
Operating: 40 °C (104 °F) @ 95% relative humidity, non-condensing
Storage: 60 °C (140 °F) @ 95% relative humidity, non-condensing
1.3.9.3 Vibrations
IEC60068-2-64: Random vibration test during operation at 3.5 Grms
1.3.9.4 Drop Test (Shock)
Federal Standard 101 Method 5007 test procedure with standard packing
1.3.9.5 EMC
CE EN55022 Class B and FCC Certifications: validate with standard development
boards in Advantech chassis
1.3.10 MTBF
Please refer Advantech SOM-7583 Series Reliability Prediction Report No:
21R200A0
1.3.11 OS Support
The mission of Advantech Embedded Software Services is to “Enhance quality of life
with Advantech platforms and Microsoft Windows embedded technology.” We enable
Windows Embedded software products on Advantech platforms to more effectively
support the embedded computing community. Customers are freed from the hassle
of dealing with multiple vendors (hardware suppliers, system integrators, embedded
OS distributors) for projects. Our goal is to make Windows Embedded Software solu-
tions easily and widely available to the embedded computing community.
To install the drivers, please connect to the Internet and browse the website http://
support.advantech.com.tw to download a setup file.

SOM-7583 User Manual 10
1.3.12 Advantech iManager
iManager supports APIs for GPIO, smart fan control, a multi-stage watchdog timer,
outputs, temperature sensors, and hardware monitor. Follow by PICMG EAPI 1.0
specifications that provide backwards compatibility.
1.3.13 Power Consumption
Hardware Configurations:
1. MB: SOM-7583C7-S8A1 (PCB: A101-2)
2. DRAM: Total 16GB (Micron 16GB LPDDR4x 4266MT/s )
3. Carrier board: SOM-DB5830 A201-2
Test Condition:
1. Test temperature: room temperature (about 25 °C; 77 °F)
2. Test voltage: rated voltage DC +12.0V
3. Test loading:
–Maximum load mode: Running programs.
–Idle mode: DUT power management off and no running any program.
4. OS: Windows 10 Enterprise
1.3.14 Performance
For reference performance or benchmark data that compare with other module,
please refer to “Advantech COM Performance and Power Consumption Table”.
Power Consumption Table (Watt.)
VCC=12V,
VSB=5V Active Power Domain Suspend Power Domain
Mechanical
off
Power State S0 Max. Load S0 Burn-in S0 Idle S5 S5 Deep Sleep RTC (uA)
SOM-
7583C7-S8A1 61.981W 36.67W 8.672W 2.012 W0.552W 12.614uA