Advantech 3U Compact PCI User manual

MIC-3321
3U CompactPCI Pentium M
760 2.0G High-performance
Controller
User Manual

MIC-3321 User Manual ii
Copyright Notice
This document is copyrighted, 2004. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from its
use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
Fast EtherChannel (FEC) is a trademark of Cisco Systems, Inc.
Intel, Pentium, and Celeron are trademarks of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation.
NetWare is a trademark of Novell, Inc.
Symbios is a trademark of Symbios Logic Corporation.
PICMG, CompactPCI and the PICMG, and CompactPCI logos are trade-
marks of the PCI Industrial Computers Manufacturers Group.
All other product names or trademarks are properties of their respective
owners.
Part No. 2003332100 1st Edition
Printed in Taiwan June 2006

iii
Product Warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free from defects in materials and workmanship for two
years from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware and
software used, etc.) Note anything abnormal and list any onscreen
messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual,
product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows us
to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty
service.
5. Write the RMA number visibly on the outside of the package and ship
it prepaid to your dealer.
CE Notification
The MIC-3321, developed by Advantech CO., LTD., has passed the CE
test for environment specification when shielded cables are used for
external wiring and sleeve core clamps are added to the USB cables. We
recommend the use of shielded cables and sleeve core clamps.

MIC-3321 User Manual iv
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, appli-
cation software, etc.)
- A complete description of the problem
- The exact wording of any error messages
Packing List
Before setting up the system, check that the items listed below are
included and in good condition. If any item does not accord with the
table, please contact your dealer immediately.
• One MIC-3321 all-in-one single board computer
• One utility CD-ROM
• This user’s manual
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the
products from damage.
1. To avoid electrical shock, always disconnect the power from your
PC chassis before you work on it. Don't touch any components on
the CPU card or other cards while the PC is on.
2. Disconnect power before making any configuration changes. The
sudden rush of power as you connect a jumper or install a card may
damage sensitive electronic components.

v Table of Contents
Contents
Chapter 1 Hardware Configuration ................................ 2
1.1 Introduction ....................................................................... 2
1.2 Specifications .................................................................... 3
1.2.1 Standard SBC Functions ................................................ 3
1.2.2 Display ........................................................................... 4
1.2.3 Mechanical and Environmental Specifications .............. 4
1.3 Function Block Diagram ................................................... 4
Figure 1.1:MIC-3321 Function Block Diagram ............ 4
1.4 Board Dimensions ............................................................. 5
Figure 1.2:MIC-3321 Board Dimensions ...................... 5
1.5 Dip Switch Settings........................................................... 5
1.5.1 Switch Locations ............................................................ 6
Table 1.1:MIC-3321 Switch Descriptions ..................... 6
Figure 1.3:MIC-3321 S1 Location (1F) ......................... 6
Figure 1.4:MIC-3321 S2 Location (2F) ......................... 7
1.6 Safety Precautions ............................................................. 7
Chapter 2 Connecting Peripherals ................................ 10
2.1 Connectors....................................................................... 10
Figure 2.1:MIC-3321 Connector Locations (1F) ......... 10
Figure 2.2:MIC-3321 Connector Locations (2F) ......... 10
Figure 2.3:MIC-3521 Connectors ................................ 11
Table 2.1:MIC-3321 Connectors Overview ................ 12
2.2 Card Installation .............................................................. 13
Figure 2.4:Chassis Installation/Removal ..................... 14
Chapter 3 Software Configuration ................................ 16
3.1 Overview ......................................................................... 16
3.2 Utilities and Drivers ........................................................ 16
3.2.1 Intel Chipset Software Installation Utility ................... 16
3.2.2 Intel VGA Graphics Driver .......................................... 16
3.2.3 Intel Gigabit LAN Driver ............................................ 16
Chapter 4 Award BIOS Setup........................................ 18
4.1 Introduction ..................................................................... 18
Figure 4.1:Setup Program Initial Screen ...................... 18
4.2 Entering Setup ................................................................. 18
4.2.1 Standard CMOS Setup ................................................. 19
Figure 4.2:Standard CMOS Setup Screen. .................. 19
4.2.2 Advanced BIOS Features Setup .................................. 20
Figure 4.3:Advanced BIOS features setup screen ....... 20
4.2.3 Advanced Chipset Features Setup ............................... 24
Figure 4.4:Advanced Chipset Features setup screen ... 24
4.2.4 Integrated Peripherals .................................................. 26
Figure 4.5:Integrated Peripherals Setup ....................... 26

MIC-3321 User Manual vi
4.2.5 PNP/PCI Configuration Setup ..................................... 29
Figure 4.6:PNP/PCI configuration screen ................... 29
4.2.6 PC Health Status .......................................................... 30
Figure 4.7:PC Health Status setup screen .................... 31
4.2.7 Spread Spectrum Control ............................................ 32
Figure 4.8:PC Health Status setup screen .................... 32
4.2.8 Load Optimized Defaults ............................................. 32
4.2.9 Set Password ................................................................ 33
4.2.10 Save & Exit Setup ........................................................ 34
4.2.11 Exit Without Saving ..................................................... 34
Appendix A Watchdog Timer Programming................... 36
Appendix B Pin Assignment .............................................. 38
Table B.1:MIC-3321 Connectors Overview ................ 38
B.1 CompactFlash Interface................................................... 39
Table B.2:CompactFlash Interface Pin Definitions ..... 39
B.2 USB 2.0 Ports.................................................................. 40
Table B.3:USB 1.1 Ports Pin Definitions .................... 40
B.3 VGA Connector............................................................... 40
B.4 COM port ........................................................................ 41
Table B.4:COM Port Pin Definitions .......................... 41
B.5 PS/2 Keyboard and Mouse Connector ............................ 41
Table B.5:PS/2 Keyboard & Mouse Port Pins ............. 41
B.6 Ethernet 10/100/1000Base-T RJ-45 Connector .............. 42
Table B.6:Ethernet Connector Definitions .................. 42
B.7 Secondary IDE 44-pin 2mm Conn. ................................. 42
Table B.7:Secondary IDE Connectors (2.5" HDD) ..... 43
B.8 Serial ATA0 (7pin connector)......................................... 44

22
CHAPTER
1
Hardware
Configuration

MIC-3321 User Manual 2
Chapter 1 Hardware Configuration
1.1 Introduction
MIC-3321 is a 3U, all-in-one, controller board, compliant with PICMG
2.0 R2.1 CompactPCI specifications. For high computing performance,
MIC-3321 uses an Intel Pentium M 760 2.0GHz CPU and Intel 915GM
chipset. This CPU provides high performance with its on-chip 2 MB L2
cache and is delivered in a Micro-FCBGA 479 package.
MIC-3321 offers powerful functions on a 3U-sized board for perfor-
mance-demanding applications like real-time machine control and indus-
trial automation.
Compact Mechanical Design
In order to decrease the thermal effect, Advantech provides a heat sink
specially designed for the MIC-3321, so it only needs external cooling air
from the chassis fans for ventilation.
Ordering Information
• MIC-3321S: Pentium M 2.0GHz, 2Mbyte L2 cache,512Mbyte
soldered DDR2 SDRAM, 4HP width
• MIC-3321: Pentium M 2.0GHz, 2Mbyte L2 cache,512Mbyte
soldered DDR2 SDRAM, 8HP width
• MIC-3321CS: Celeron M 1.0GHz, 512Kbyte L2 cache,512Mbyte
soldered DDR2 SDRAM, -25~70° C, 4HP width
• MIC-3321C: Celeron M 1.0GHz, 512Kbyte L2 cache, 512Mbyte
soldered DDR2 SDRAM, -25~70°c, 8HP width
• MIC-3321LS: Celeron M 800MHz, 0Kbyte L2 cache,
256Mbyte soldered DDR2 SDRAM, 4HP width
• MIC-3521-AE: Rear I/O Transition Board for MIC-3321 series

3 Chapter1
1.2 Specifications
1.2.1 Standard SBC Functions
• CPU: MIC-3321 supports Intel Pentium M 2.0 GHz
• Optional: Celeron M 1.0GHz/ Celeron M 800MHz (non cache)
• BIOS: Award 4 Mb flash memory
• Chipset: Intel 915GM Graphics and Memory Controller Hub (GMCH)
Intel 82801FBM I/O Controller Hub (ICH6M)
• System Memory:
Directed Soldered 512MB DDR2 533 SDRAM (MIC-3321/3321S)
Directed Soldered 512MB DDR2 400 SDRAM (MIC-3321C/3321CS)
Directed Soldered 256MB DDR2 400 SDRAM (MIC-3321LS)
Max:1GB
• P-IDE: One Channel IDE CompactFlash socket type II*1(select mas-
ter/slave DIP-SW), UltraDMA/100/66/33*a (2.5"HDD)
• SATA: One external SATA Connector
• Serial Ports: Two RS-232 ports with 16C550UARTs (or compatible)
with 16-byte FIFO buffer. One Front I/O, the other Rear I/O.
• Keyboard and PS/2 Mouse Connector: One 6-pin mini-DIN connec-
tor is located on the mounting bracket for easy connection to a key-
board or PS/2 mouse.
• USB Port: Four USB2.0 Channels up to 480MB, 2 front I/O, 2 rear I/O
• PCI-to-PCI Bridge: PERICOM P17C8150-32-bit/33MHz Compact-
PCI interface
• Watchdog Timer: Provides system reset and software control. Time
interval is programmable from 1 to 255 seconds/minutes.
• Ethernet LAN: 10/100/1000Base-TX Gigabit Ethernet
• Controller Chips: Two Intel 825723E/L PCI Express Gigabit Ethernet
Controllers support Pre-boot Execution Environment(PXE).
• Battery-backup RAM: 512 KB
• Input /Output Bus Interface: PCI 2.2 compliant, 32 bit/33 MHz
• CompactPCI Compliance: PICMG 2.1 CompactPCI Hot Swap R3.0

MIC-3321 User Manual 4
1.2.2 Display
• Controller: Intel Graphics Media Accelerator 900
• VRAM: DVMT3.0 128MB
• Resolution: Up to 2048x1536 with 32-bit color at 75Hz
1.2.3 Mechanical and Environmental Specifications
• Board Size (W x H) : 160 x 100 mm (3U)
• Operating Temperature:0 ~ 50° C (MIC-3321 Pentium M 2.0GHz)
0~50° C (MIC-3321LS Celeron M 800MHz)
-25 ~ 70° C (MIC-3321C Celeron M 1.0G)
• Storage Temperature: -40 ~ 80° C
• Board Weight: 0.6 kg
1.3 Function Block Diagram
Figure 1.1: MIC-3321 Function Block Diagram