Advantech PCM-3910 Installation and operation manual

1 PCM-3910 Startup Manual P/N:2006391000
PCM-3910 DC to DC power supply PC/104+
Module
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
• 1 PCM-3910
• 1 Startup manual
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Mechanical and Environmental
• Dimensions (L x W): 3.55" x 3.75" x 0.55"
• Weight: 30g
• Operating Temperature: -40 ~ 85°C(-40~185°F)
• Storage temperature: -40 ~ 85°C(-40~185°F)
• Operating Humidity: 0%~90% ralative humity,non-con-
densing
• Power Supply Voltage: 5V
• Power Consumption: 5V, ±5%
50W output
10V to 24V DC input range
Reverse input protection
5V,12V,-5V,-12V outputs
Packing list Specifications
Note 1: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/Prodindex/acrobat/read-
step.html(Acrobat is a trademark of Adobe.)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service, please visit our
support website at:
http://service.advantech.com.tw/eservice/
This manual is for the PCM-3910 series Rev. A1.
Part No. 2006391000 1st Edition
Mar. 2005
5V output 10A
12Voutput 2A
-5Voutput 0.4A
-12Voutput 0.4A
10V~24V input 6.5A
Features
PCM-3910 DC to DC power supply PC/104+ Module51 SBC Low Power Intel Tilamook 266MHz,430T
X

2 PCM-3910 Startup Manual P/N:2006391000
Connectors on the board link it to external devices, such
as hard disk drives, a keyboard or expansion bus connec-
tors. In addtion, the board has a number of jumpers that
allow you to configure your system to suit your applica-
tion.
The table below lists the function of each of the jumpers
and connectors.
Dimensions
Component Placement
Jumpers & Connectors
Connectors
Label Function
CN1 Power Input Connector
CN2 PC/104+ connector
CN3 Power Output Connector
CN1
Pin Pin name
1Vi+
2GND
CN3
Pin Pin name
15V
25V
3GND
4GND
5GND
6 12V
7 -12V
8-5V
Board Layout

3 PCM-3910 Startup Manual P/N:2006391000
This device complies with the requirements in part 15 of the
FCC rules: Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, incliding interference
that may cause undesired operation
This equipment has been tested and found to aomply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection agaonst harmful interference
when the equipment is operated in a commerical enviroment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not
insalled and used in accordance with the instruction manual, may cause
harmful interference to radio communications.Operation of this device in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his/her own expense. The user
is advised that any equipment changes or modifications not expressly
approved by the party responsible for compliance would void the compliance
to FCC regulations and therefore, the user’s authority to operate the equip-
ment.
Caution!
Achtung!
There is a danger of a new battery exploding if it is incorrectly
installed. Do not attempt to recharge, force open, or heat the
battery. Replace the battery only with the same or equivalent
type recommended by the manufacture. Discard used batteries according to
the manufacture’s instruction.