Advantech PCM-23C1CF User manual

Description of Pin Use — CN2, CFast Connector
PINS1 GND PINPC6 NC
PINS2 SATA_TX+ PINPC7 GND
PINS3 SATA_TX- PINPC8 NC
PINS4 GND PINPC9 NC
PINS5 SATA_RX- PINPC10 NC
PINS6 SATA_RX+ PINPC11 NC
PINS7 GND PINPC12 NC
PINPC1 NC PINPC13 3.3 V
PINPC2 GND PINPC14 3.3 V
PINPC3 NC PINPC15 GND
PINPC4 NC PINPC16 GND
PINPC5 NC PINPC17 NC
STARTUP MANUAL
1 Startup Manual
PCM-23C1CF
1 x CFast slot with cover protection
Packing List
Before installation, please ensure that the following items
have been included in your shipment:
1 x CFast I/O plate with 1 x iDoor bracket
1 x Startup manual
1 x Warranty card
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Pin Assignment — Internal Connection
Notes
For more information about this or other Advantech
products, visit our website at
http://www.advantech.com
http://www.advantech.com/eAutomation
For technical support and service, visit
http://www.advantech.com.tw/eservice
This manual is for PCM-23C1CF
Part No: 200323C101 Edition 2
September 2017
The pin assignments for one of the I/O module
connectors are shown in the tables and gures below.
Pin Assignment
Documentation/Software Support Guide
Installation
The PCM-23C1CF module with iDoor technology
supports the following iAutomation computing platforms:
UNO-2000 standard mount series
UNO-1000 DIN rail mount series
UNO-3000 wallmount series
4:3 TPC-xx51T/xx82, TPC-5000 panel PCs
16:9 TPC-xx51WP/xx81WP, TPC-5000 panel PCs
*Note: An additional SATA cable may be required to
install the PCM-23C1CF module on a TPC
system.
Advantech’s PCM-23C1CF module is a SATAII (3G/s)
to CFast interface for storage applications and does not
require a driver.
Description of Pin Use — CN1
PINS1 GND PINP5 GND
PINS2 SATA_TX+ PINP6 GND
PINS3 SATA_TX- PINP7 5 V
PINS4 GND PINP8 5 V
PINS5 SATA_RX- PINP9 5 V
PINS6 SATA_RX+ PINP10 GND
PINS7 GND PINP11 NC
PINP1 3.3 V PINP12 GND
PINP2 3.3 V PINP13 NC
PINP3 3.3 V PINP14 NC
PINP4 GND PINP15 NC
I/O Board CN1 — SATA HDD Cable

Startup Manual 2
TPC Panel PC Installation
1. Unscrew the backplate screws and remove the
backplate.
UNO Embedded Computer Installation
1. Unscrew the base plate screws and remove the
base plate.
2. Unscrew the blacking plate screws and remove the
blanking plate.
3. Insert the PCM-23C1CF module through the
blanking plate slot.
4. Secure the PCM-23C1CF module using the screws
removed from the blanking plate.
2. Unscrew the blacking plate screws to remove the
blanking plate.
5. Connect the PCM-23C1CF module to the SATA
connector on the motherboard using a SATA cable.
3. Insert the PCM-23C1CF module through the blanking
plate hole.
5. Connect the PCM-23C1CF module to the SATA
connector using a SATA cable.
4. Secure the PCM-23C1CF module using the screws
removed from the blanking plate.