Advantech ASMB-BMC Installation and operation manual

ASMB-BMC Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. ASMB-BMC module x 1
2. 2-year quality warranty card x 1 P/N: 2190000902
3. Startup manual x 1 P/N: 20060BMC00
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
ASMB-BMC
BMC Module IPMI 2.0
Startup Manual
Standard Functions
• ASMB-BMC is compliant with Intel IPMI 2.0 specification
via IPMI connector on ASMB series server boards
• Support list: ASMB-781G4, ASMB-820I, ASMB-920IR,
ASMB-822I
Mechanical
• Dimensions: 36 mm x 15 mm
• Power supply type: 3.3 V, 5 V, 5 VSB
• Power requirements: 3.3 VSB
• Operating temperature: 0 ~ 60° C
• Operating humidity: 40° C @ 85% RH, Non-Condensing
• Storage temperature: -40 ~ 85° C
• Storage humidity: 60° C @ 95% RH, Non-Condensing
• Weight: 0.01 kg
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/suppot/
This manual is for the ASMB-BMC Series.
Part No. 20060BMC00
Print in China
1st Edition
July 2013

2 ASMB-BMC Startup Manual
1. Start to use ASMB-BMC by the following steps.
1). Connect ASMB-BMC to location “IPMI1”, reference
location please check the manual of server board.
Example: ASMB-781
2). ASMB-BMC.
IPMI1
Installation Guide
Jumpers and Connectors
There is one connector on the module to connect with
server board. The below table lists the function of this con-
nector.
Jumpers and connectors
Connectors
Label Function
CN2 IPMI connector
Pin Denitions
Pin Signal Pin Signal
1 FLA_SPICK 2 ASTSPI_CE0#
3 FLA_WPN 4 N/A
5 FLA_SPIDIO 6 GND
7 ROMA0
4
2

ASMB-BMC Startup Manual 3
2. After setting up the hardware configuration, complete
the BIOS settings below.
1). Check the information below to find out corre-
sponding commands to enable the BMC function.
Enter Server Mgmt, “BMC Support” and “Wait For
BMC” are [Enabled].
Enter BMC network configuration, when “Configu-
ration Change Address source” is [Static], there is
a default IP address for first time user setting.
For some server boards that provide two LAN
options for BMC, the BIOS screen will show LAN1
and LAN2 information in the BMC network configu-
ration screen.
Note: It will take 1 minute to initialize when first time
connected to power on.
Installation Guide
3. Set the IP address to the same segment as the
connected LAN channel of ASMB-BMC in the
client computer.
4. Open a browser and log into GUI (Graphic User
Interface) of ASMB-BMC. Hyperlink Address is the
same as the connected LAN channel IP address
from the client computer.
Default user name and password
Username admin
Password admin

4 ASMB-BMC Startup Manual
Board Layout and Dimensions
Figure 1: ASMB-BMC Board Layout and Dimensions

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Advantech:
ASMB-BMC-00A1E