Advantech MIO-6250 MIO/160 Installation and operation manual

MIO-6250 Startup Manual 1
MIO-6250 MIO/160 Module with 3 LANs
Startup Manual
The most flexible interface for Embedded
Applications
Today is an embedded world, but many standard
embedded single board computers cannot 100% meet
application specifications because they are not flexible
enough to expand and develop the system.
A system design short cut
Module I/O160 (MIO/160) is an open pin definition
interface from Advantech. The MIO/160 interface inte-
grates the most popular data buses into a high-density
160-pin connector, including, PCI, USB, DVO, SMBus,
LPC, and AC97. With MIO/160, board engineers can
speed up system project design and expand the sys-
tem easily.
Before you begin installing your card, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
• Chipset: Onboard 3 Realtek RTL8139DL 10/100BaseT
Fast Ethernet Controllers
• Ethernet Port: 3 RJ-45 connector
• LAN bypass: Supports LAN bypass function on LAN 2
and LAN 3 by GPO pins.
• Ethernet disable: LAN port can be disable by onboard
switch.
• LED indicator:
Active (Tx/Rx) LED: The LED lights "Blinking Orange"
when the respective port is successfully connected to
an Ethernet port.
Link (10/100 Mbps) LED: The LED lights "Solid Green
On" when the respective port is successfully connected
to 10/100Mbps Ethernet network device of the ports.
Mechanical and Environmental
• Dimensions (L x W): 102mm x 70mm
• Operating Temperature: 0 ~ 60°C operation
• Operating Humidity: 0%~90% relative humity, non-con
densing
• Power Supply Voltage: 5V
• Power Requirements: 5V @100mA
• 3 Fast Ethernet ports
• LAN by pass function
• Ethernet disable function
Introduction Specifications
Packing list
• 1 MIO-6250
• 1 Startup manual
• 1 CD ROM for MIO-6250 Driver/Utility
• 1 screw kit
- copper stud x 4 pcs p/n: 1930000058
- screw x 4 pcs p/n: 1935030500
• 1 Mini Jumper kit (black)
- mini jumper x 10 pcs p/n: 1653302122
Note 1: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/products/acrobat/
readstep2.html(Acrobat is a trademark of
Adobe.)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the MIO-6250 series Rev. A1.
Part No. 2006625000 1st Edition
May 2006
Features
MIO-6250 MIO/160 Module with 3 LANs

2 MIO-6250 Startup Manual
Connectors on the board link it to external devices, such
as hard disk drives, a keyboard or expansion bus connec-
tors. In addition, the board has a number of jumpers that
allow you to configure your system to suit your applica-
tion.
The table below lists the function of each of the jumpers
and connectors.
Component Placement
Jumpers & Connectors
Connectors
Label Function
CN1 LAN-1 Connector
CN2 LAN-3 Connector
CN3 LAN-2 Connector
JP1 Relay ON/OFF Jumper
JP2 Relay ON/OFF Control Jumper
SW1 LAN Chip Enable/ Disable Select
CN1 LAN-1 Connector Type: RJ-45
Pin Pin name Pin Pin name
1 LAN1TX+ 2 LAN1TX-
3 LAN1RX+ 4 LAN1RTXCT
5LAN1TXCT 6LAN1RX-
7 LAN1RXCT 8 LAN1RXCT
9GND 10GND
11 LAN-1 LED VCC 12 LAN-1 ACT LED
13 LAN-1 LED VCC 14 LAN-1 LINK LED
*low active
CN2 LAN-3 Connector Type: RJ-45
Pin Pin name Pin Pin name
1 LAN3TX+ 2 LAN3TX-
3 LAN3RX+ 4 LAN3RTXCT
5 LAN3TXCT 6 LAN3RX-
7 LAN3RXCT 8 LAN3RXCT
9GND 10GND
11 LAN-3 LED VCC 12 LAN-3 ACT LED
13 LAN-3 LED VCC 14 LAN-3 LINK LED
*low active
CN3 LAN-2 Connector Type: RJ-45
Pin Pin name Pin Pin name
1 LAN2TX+ 2 LAN2TX-
3 LAN2RX+ 4 LAN2RTXCT
5 LAN2TXCT 6 LAN2RX-
7 LAN2RXCT 8 LAN2RXCT
9GND 10GND
11 LAN-2 LED VCC 12 LAN-2 ACT LED
13 LAN-2 LED VCC 14 LAN-2 LINK LED
*low active
JP1: Relay ON/OFF Select *: Default Value
Pin Function
2-3 Relay ON * (Default)
1-2 Relay ON/OFF By GPIO
NC Relay OFF
JP2: Relay ON/OFF Select *: Default Value
Pin Function
2-3 GPIO Control
1-2 Auto ON * (Default)
SW1: LAN Chip Enable/ Disable Select *: Default Value
Pin Function
SW1-1 (on/off) LAN-1 Enable*/ Disable
SW1-2 (on/off) LAN-2 Enable*/ Disable
SW1-3 (on/off) LAN-3 Enable*/ Disable
SW1-4 (on/off) NC
Board Layout

MIO-6250 Startup Manual 3
Dimensions
FCC This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the fol-
lowing two conditions:
1.This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undes-
ired operation
This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this device in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his/her own expense. The user is advised that any equipment
changes or modifications not expressly approved by the party responsible for compliance would void
the compliance to FCC regulations and therefore, the user's authority to operate the equipment.
Caution!
Achtung!
There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge,
force open, or heat the battery. Replace the battery only with the same or equivalent type recom-
mended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.