Advantech ARK-3380 User manual

ARK-3380
Embedded Box Computer
User Manual

ARK-3380 User Manual ii
Copyright
The documentation and the software included with this product are copy-
righted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli-
able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
All other product names or trademarks are properties of their respective
owners.
Part No. XXXXXXXXXX 1st Edition
Printed in Taiwan April 2005

iii
Product Warranty (1 year)
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for one year
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war-
ranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

ARK-3380 User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring. We recommend the use
of shielded cables. This kind of cable is available from Advantech. Please
contact your local supplier for ordering information.
This product has passed the CE test for environmental specifications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged
by ESD (Electrostatic Discharge) and EMI leakage, we strongly recom-
mend the use of CE-compliant industrial enclosure products.
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference
at his own expense.

v
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer
service center for technical support if you need additional assistance.
Please have the following information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application
software, etc.)
- A complete description of the problem
- The exact wording of any error messages
ARK-3381 Series Model
There are three sub-models in ARK-3380 series listed below:
Table 1.1: ARK-3380 Model list
Packing list
Before installing your board, make sure that the following materials have
been received:
• Warranty certificate
• Software Supporting CD-ROM
• 6P-6P-6P 20cm KB and PS/2 Mouse Y cable (P/N: 1700060202)
• DIN-rail mounting accessory (P/N: 1997001110, 1997001120,
1997001130,
1997001140)
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
ARK-3380-
1M0A1:
ULV CeleronRM 600 MHz Embedded Box Computer, with
DVI, LVDS, Audio, Fast Ethernet, S-Video, C-Video, 1 x
RS-232, 1 x RS-232/422/485
ARK-3380-
1S1A1:
LV PentiumRM 1.1 GHz Embedded Box Computer, with
DVI, LVDS, Audio, Fast Ethernet, S-Video, C-Video, 1 x
RS-232, 1 x RS-232/422/485
ARK-3380-
1S4A1:
LV PentiumRM 1.4GHz, Embedded Box Computer, with
DVI, LVDS, Audio, Fast Ethernet, S-Video, C-Video, 1 x
RS-232, 1 x RS-232/422/485

ARK-3380 User Manual vi
Safety Instructions
1. Please read these safety instructions carefully.
2. Please keep this User‘s Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning.
Don‘t use liquid or sprayed detergent for cleaning. Use moisture sheet or
clothe for cleaning.
4. For pluggable equipment, the socket-outlet shall near the equipment
and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when install. A drop or fall
could cause injury.
7. Do not leave this equipment in an uncontrolled environment; storage
temperatures above 60ºC may damage the equipment.
8. The openings on the enclosure are for air convection hence protecting
the equipment from overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source when connecting the equip-
ment to the power outlet.
10. Place the power cord such a way that people cannot step on it. Do not
place anything over the power cord. The power cord must be rated for the
product and for the voltage and current marked on the product’s electrical
ratings label. The voltage and current rating of the cord should be greater
than the voltage and current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for long time, disconnect the equipment
from mains to avoid being damaged by transient over-voltage.
13. Never pour any liquid into ventilation openings; this could cause fire
or electrical shock.
14. Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
15. If one of the following situations arise, get the equipment checked by
service personnel:
a. The Power cord or plug is damaged.
b. Liquid has penetrated the equipment.
c. The equipment has been exposed to moisture.

vii
d. The equipment has not worked well or you can not get it work
according to user‘s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage
CAUTION!
THIS COMPUTER IS PROVIDED WITH A BATTERY-POW-
ERED REAL-TIME CLOCK CIRCUIT. THERE IS A DANGER
OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH SAME OR EQUIVLENT TYPE RECOM-
MENDED BY THE MANUFACTURE. DISCARD USED BATTER-
IES ACCORDING TO THE MANUFACTURER’S
INSTRUCTIONS.
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Ver-
wenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein
angefeuchtetes Tuch zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein
Kippen oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abge-
deckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen
kann. Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten
Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung
eine Beschädigung vermieden.

ARK-3380 User Manual viii
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüs-
sigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elek-
trischen Schlag auslösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elek-
trischen Sicherheit nur von authorisiertem Servicepersonal geöffnet wer-
den.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu
trennen und von einer qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktion-
iert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Bat-
terie.Ersatz nur durch densellben order einem vom Hersteller emp-
fohlene-mahnlichen Typ. Entsorgung gebrauchter Batterien navh
Angaben des Herstellers.
16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf
nicht fach-männische Weise gewechselt wird. Verfangen Sie die Batterie
nur gleicher oder entsprechender Type, wie vom Hersteller empfohlen.
Entsorgen Sie Batterien nach Anweisung des Herstell-ers.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend
der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die
Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the
products from damage.
1. To avoid electrical shock, always disconnect the power from your PC
chassis before you work on it. Don't touch any components on the CPU
card or other cards while the PC is on.
2. Disconnect power before making any configuration changes. The sud-
den rush of power as you connect a jumper or install a card may damage
sensitive electronic components.

ix Table of Contents
Contents
Chapter 1 Overview .......................................................... 2
1.1 Introduction ....................................................................... 2
1.2 Features ............................................................................. 2
1.2.1 Dual Display, Video Intensive capacity ........................ 2
1.2.2 Highly Robust Casting Construction ............................. 2
1.2.3 Highly Compact Size ..................................................... 2
1.2.4 Highly Scalable Performance with low power consump-
tion 2
1.2.5 Optimized Integration .................................................... 2
1.3 Hardware Specification ..................................................... 3
1.3.1 Processor Core Logic System ........................................ 3
1.3.2 Display ........................................................................... 3
1.3.3 Ethernet .......................................................................... 3
1.3.4 Audio ............................................................................. 4
1.3.5 Other .............................................................................. 4
1.3.6 Storage ........................................................................... 4
1.3.7 Mechanical ..................................................................... 4
1.3.8 Power Supply ................................................................. 4
1.3.9 Environment Specifications ........................................... 5
1.4 Chassis Dimensions........................................................... 6
Figure 1.1:Chassis Dimensions ...................................... 6
Chapter 2 Hardware Functionality ................................. 8
2.1 Introduction of ARK-3380 External I/O Connectors........ 8
Figure 2.1:ARK-3380 front metal face plate external I/O
connectors 8
Figure 2.2:ARK-3380 rear metal face plate I/O connec-
tors 8
2.2 ARK-3380 front metal face plate external I/O connectors 9
2.2.1 Power ON/OFF Button .................................................. 9
2.2.2 LED Indicators ............................................................... 9
2.2.3 LVDS Connector ........................................................... 9
Figure 2.3:LVDS Connector .......................................... 9
Table 2.1:LVDS Connector Pin Assignment ............... 10
2.2.4 LCD Backlight On/Off control Connector .................. 10
Figure 2.4:LCD Backlight connector ........................... 10
Table 2.2:LCD Backlight Connector Pin Assignment . 11
2.3 ARK-3380 rear metal face plate external I/O connectors11
2.3.1 Power Input Connector ................................................ 11
Figure 2.5:Power Input Connector ............................... 11
Table 2.3:Power connector pin assignments ................ 11
2.3.2 COM1 Connector ......................................................... 11
Figure 2.6:COM 1 connector ....................................... 12
Table 2.4:COM1 standard serial port pin assignments 12

ARK-3380 User Manual x
2.3.3 COM2 Connector ......................................................... 12
Figure 2.7:COM 2 connector ....................................... 12
Table 2.5:COM2 standard serial port pin assignments 13
2.3.4 Audio Connector .......................................................... 13
Table 2.6:Line_In connector ........................................ 13
Table 2.7:Speaker_Out connector ................................ 13
Table 2.8:Mic_In connector ......................................... 13
2.3.5 DVI Connector ............................................................. 14
Table 2.9:DVI connector pin assignments ................... 14
2.3.6 S-Video Connector ...................................................... 14
Figure 2.8:S-Video connector ...................................... 15
2.3.7 Composite Video Connector ........................................ 15
Figure 2.9:Composite-Video connector ....................... 15
2.3.8 Ethernet Connector (LAN) .......................................... 15
Figure 2.10:Ethernet connector .................................... 15
Table 2.10:RJ-45 Connector pin assignments ............. 16
2.3.9 Reset Button ................................................................. 16
2.3.10 PS2 Keyboard/Mouse Connector ................................. 16
Figure 2.11:PS/2 connector .......................................... 16
Table 2.11:PS/2 Keyboard/Mouse connector pin assign-
ments 17
2.3.11 VGA Connector ........................................................... 17
Figure 2.12:VGA connector ........................................ 17
Table 2.12:VGA connector pin assignment ................. 17
2.3.12 USB Connector ............................................................ 18
Figure 2.13:USB connector ......................................... 18
Table 2.13:USB Connector .......................................... 18
Chapter 3 Hardware Installation and Upgrade ........... 20
3.1 Jumpers and Connectors.................................................. 20
3.2 Setting jumpers................................................................ 20
3.3 COM2 RS-232/422/485 Jumper setting (J3/J4/J5) ......... 21
Table 3.1:COM2 RS-232/422/485 Jumper Selection .. 21
3.4 LCD Power Jumper Setting (J6) ..................................... 21
Table 3.2:LCD Power Setting (J6) .............................. 21
3.5 NTSC/PAL TV type Setting (J1) .................................... 22
Table 3.3:Type 3.3: NTSC/PAL TV selection(J1) ..... 22
3.6 Installing the DDR SDRAM Memory Module............... 22
3.7 Inserting a Compact Flash Card...................................... 23
Figure 3.1: ................................................................... 23
Figure 3.2: ................................................................... 24
Figure 3.3: ................................................................... 24
Figure 3.4: ................................................................... 25
3.8 Installing the 2.5" Hard Disk Drive (HDD) .................... 25
3.9 Connecting Power ........................................................... 26
Chapter 4 Award BIOS Setup........................................ 28
4.1 Introduction ..................................................................... 28
4.1.1 CMOS RAM Auto-backup and Restore ...................... 28
4.2 Entering Setup ................................................................. 28

xi Table of Contents
Figure 4.1:Award BIOS Setup initial screen ............... 29
4.3 Standard CMOS Setup .................................................... 29
Figure 4.2:Standard CMOS features screen ................ 29
4.4 Advanced BIOS Features................................................ 30
Figure 4.3:Advanced BIOS features screen ................. 30
4.4.1 CPU Feature ................................................................. 30
4.4.2 Virus Warning .............................................................. 30
4.4.3 CPU L1 & L2 Cache .................................................... 30
4.4.4 Quick Power On Self Test ........................................... 30
4.4.5 First/Second/Third/ Boot Other Device ....................... 30
4.4.6 Swap Floppy Drive ...................................................... 31
4.4.7 Boot UP Floppy Seek .................................................. 31
4.4.8 Boot Up NumLock Status ............................................ 31
4.4.9 Gate A20 Option .......................................................... 31
4.4.10 Typematic Rate Setting ................................................ 31
4.4.11 Typematic Rate (Chars/Sec) ........................................ 31
4.4.12 Typematic Delay (msec) .............................................. 31
4.4.13 Security Option ............................................................ 31
4.4.14 APIC Mode .................................................................. 31
4.4.15 MPS Version Control For OS ...................................... 31
4.4.16 OS Select for DRAM > 64MB .................................... 32
4.4.17 Report No FDD For WIN 95 ....................................... 32
4.4.18 Small Logo (EPA) Show ............................................. 32
4.5 Advanced Chipset Features............................................. 32
Figure 4.4:Advanced Chipset features screen .............. 32
4.5.1 DRAM Timing Selectable ........................................... 33
4.5.2 CAS Latency Time ...................................................... 33
4.5.3 Active to Precharge Delay ........................................... 33
4.5.4 DRAM RAS# to CAS# Delay ..................................... 33
4.5.5 DRAM RAS# Precharge .............................................. 33
4.5.6 DRAM Data Integrity Mode ........................................ 33
4.5.7 MGM Core Frequency ................................................. 33
4.5.8 System BIOS Cacheable .............................................. 33
4.5.9 Video BIOS Cacheable ................................................ 33
4.5.10 Memory Hole At 15M-16M ........................................ 34
4.5.11 Delayed Transaction .................................................... 34
4.5.12 Delay Prior to Thermal ................................................ 34
4.5.13 AGP Aperture Size (MB) ............................................ 34
4.5.14 On-Chip VGA .............................................................. 34
4.5.15 On-Chip Frame Buffer Size ......................................... 34
4.5.16 Boot Display ................................................................ 34
4.5.17 Panel Scaling ................................................................ 34
4.5.18 Panel Number .............................................................. 34
4.6 Integrated Peripherals...................................................... 35
Figure 4.5:Integrated Peripherals ................................. 35
4.6.1 IDE Cable Detect ......................................................... 35

ARK-3380 User Manual xii
4.6.2 IDE Master/Slave PIO/UDMA Mode, ......................... 35
4.6.3 On-Chip Secondary PCI IDE ....................................... 35
4.6.4 USB Controller ............................................................ 36
4.6.5 USB Keyboard/Mouse Support ................................... 36
4.6.6 AC97 Audio ................................................................. 36
4.6.7 Init Display First .......................................................... 36
4.6.8 Onboard LAN Control ................................................. 36
4.6.9 IDE HDD Block Mode ................................................ 36
4.6.10 Onboard FDC Controller ............................................. 36
4.6.11 Onboard Serial Port ..................................................... 36
4.6.12 UART Mode Select ..................................................... 36
4.6.13 RxD, TxD Active ......................................................... 36
4.6.14 IR Transmission Delay ................................................ 36
4.6.15 UR2 Duplex Mode ....................................................... 37
4.6.16 Onboard Parallel Port ................................................... 37
4.6.17 Parallel Port Mode ....................................................... 37
4.6.18 EPP Mode Select ......................................................... 37
4.6.19 ECP Mode Use DMA .................................................. 37
4.7 Power Management Setup............................................... 38
Figure 4.6:Power management setup screen ................ 38
4.7.1 Power-Supply Type ..................................................... 38
4.7.2 ACPI function .............................................................. 38
4.7.3 Power Management ..................................................... 38
4.7.4 Video Off In Suspend .................................................. 39
4.7.5 Modem Use IRQ .......................................................... 39
4.7.6 HDD Power Down ....................................................... 39
4.7.7 Soft-Off by PWR-BTTN ............................................. 39
4.7.8 CPU THRM-Throttling ................................................ 39
4.7.9 PowerOn By LAN ....................................................... 39
4.7.10 PowerOn By Modem ................................................... 39
4.7.11 PowerOn By Alarm ..................................................... 39
4.7.12 Primary IDE 0 (1) and Secondary IDE 0 (1) ............... 39
4.7.13 FDD, COM, LPT PORT .............................................. 39
4.7.14 PCI PIRQ [A-D]# ........................................................ 40
4.8 PnP/PCI Configurations .................................................. 40
4.8.1 PnP OS Installed .......................................................... 40
Figure 4.7:PnP/PCI configurations screen ................... 40
4.8.2 Reset Configuration Data ............................................. 40
4.8.3 Resources controlled by: .............................................. 40
4.8.4 PCI/VGA Palette Snoop .............................................. 40
4.9 Password Setting ............................................................. 41
4.10 Save & Exit Setup ........................................................... 41
4.11 Exit Without Saving........................................................ 41
Chapter 5 PCI SVGA/LCD Setup ................................. 44
5.1 Introduction .................................................................... 44
5.1.1 CMOS setting for panel type ....................................... 44

xiii Table of Contents
Figure 5.1:Advanced Chipset features screen .............. 44
5.1.2 Display type ................................................................. 45
5.1.3 Dual Independent Display ........................................... 45
Figure 5.2:Intel® 82852/82855 GM/GME Graphics Con-
troller Properties - Devices 45
Figure 5.3:Intel® 82852/82855 GM/GME Graphics Con-
troller Properties – Extended Desktop Settings 46
5.2 Installation of the SVGA Driver ..................................... 46
5.2.1 Installation of Windows 98/Me ................................... 46
Figure 5.4:Directory “Graphics” .................................. 47
5.2.2 Installation of Windows 2000 ...................................... 47
Figure 5.5:CD Directory “2.VGA” .............................. 48
Figure 5.6:Intel® Extreme Chipset Graphics Driver Soft-
ware Install Wizard 48
Figure 5.7:Intel® Extreme Graphics Driver Setup ...... 49
Figure 5.8:InstallShield® Wizard Complete ............... 49
Chapter 6 Full Disassembly Procedure ........................... 7
6.1 Introduction ....................................................................... 7
Figure 6.1: ..................................................................... 7
Figure 6.2: ..................................................................... 8
Figure 6.3: ..................................................................... 8
Figure 6.4: ..................................................................... 9
Figure 6.5: ..................................................................... 9
Figure 6.6: ................................................................... 10
Figure 6.7: ................................................................... 10
Figure 6.8: ................................................................... 11
Figure 6.9: ................................................................... 11
Figure 6.10: .................................................................. 12
Figure 6.11: .................................................................. 12
Figure 6.12: .................................................................. 13
Figure 6.13: .................................................................. 13
Figure 6.14: .................................................................. 14
Figure 6.15: .................................................................. 14
Figure 6.16: .................................................................. 15
Figure 6.17: .................................................................. 15
Figure 6.18: .................................................................. 16
Figure 6.19: .................................................................. 16

ARK-3380 User Manual xiv

2
CHAPTER
1
Overview
This chapter gives background infor-
mation on the ARK-3380. It shows you
the ark-3380 overview and specifica-
tions.
Sections include:
• Sections include:
• Introduction
• Hardware Specifications
• Chassis Dimension

ARK-3380 User Manual 2
Chapter 1 Overview
1.1 Introduction
The ARK-3380 Fan-less Embedded Box Computer combines a rich dis-
play interface and other industrial features into a rugged, compact metal
chassis for multimedia intensive applications. The fan-less operation pro-
vides noise protection to the platform when deployed in external environ-
ments. The ARK-3380 Embedded Box Computer is ideally suited for
embedded PC applications. All electronics are protected in a compact
sealed housing for convenient embedded and stand alone applications,
where space and environment considerations are critical.
1.2 Features
1.2.1 Dual Display, Video Intensive capacity
• Rich display interface of DVI, LVDS and TVout; as well as AC97 Ste-
reo audio designed for diversified applications such as Point of Infor-
mation, Gaming, Digital display broadcasting system
1.2.2 Highly Robust Casting Construction
• Fan-less operation in Aluminum sealed construction
• A special cushioned design that absorbs vibration to ensure maximum
reliability under harsh conditions
1.2.3 Highly Compact Size
• With its maximum mounting height of 69 mm, the ARK-3380 can be
used under space critical installation conditions
1.2.4 Highly Scalable Performance with low power con-
sumption
• Scalable Low Voltage and Ultra Low Voltage Pentium M class proces-
sor system to bring high computing performance with low power con-
sumption
1.2.5 Optimized Integration
• Few Parts, Easy Integration, Easy Maintenance to reduce investment
• Systems are supplied ready to run
• Long life cycle support for product continuity
• Wide range of DC 12V~24V power source offers flexibility of power
input for various automation environments.

3 Chapter1
1.3 Hardware Specification
1.3.1 Processor Core Logic System
CPU
• Intel® Ultra Low Voltage Celeron® M or Intel® Pentium® M Low
Voltage Processor, µFC-BGA 479 Package:
- ULV Celeron® M 600 MHz (for Model of ARK-3380-1M0A1)
- LV Pentium® M 1.1 GHz (for Model of ARK-3380-1S1A1)
- LV Pentium® M 1.4 GHz (for Model of ARK-3380-1S4A1)
System Chipset
• Intel® 852GM or Intel® 855GME Memory Controller Hub (GMCH)
Chipset:
- Intel® 852GM for model of ARK-3380-1M0A1
- Intel® 855GME for model of ARK-3380-1S1A1 and ARK-3380
1S4A1
- Intel® FW82801DB I/O Controller Hub 4 (ICH4) Chipset
400 MHz FSB
BIOS: 4Mbit Flash BIOS, supports Plug & Play, APM 1.2
System Memory
• One 200 pin SO-DIMM sockets
• Supports DDR SDRAM Up to 1GB
1.3.2 Display
Chipset
Integrated graphics built-in Intel® 852GM GMCH, or Intel® 855GME
GMCH, utilizing Intel® Extreme Graphics 2 technology
Display Memory
Dynamic video memory allocation up to 32 MB
Display Interface support
• CRT Interface
• 36-bit LVDS interface, optional support up to 48-bit
• DVI interface, compliant with DVI specification 1.0
• Supports both NTSC/PAL, S-Video and Composite Video output
1.3.3 Ethernet

ARK-3380 User Manual 4
Ethernet Controller: Intel® 82551ER Ethernet Controller
Speed: 10/100MBps, IEEE 802.3u (100 BASE-T) protocol compatible
1.3.4 Audio
Audio Interface
• Audio controller on the ICH4 chip
• AC97 3D surround stereo sound, Dual 6 W Amplifier
• Supports Line_In, Speaker_Out, and Microphone_In
1.3.5 Other
Watchdog Timer: 255 levels timer interval, setup by software
Serial Port: One RS-232 port (COM1) and One RS-232/422/485 port
(COM2)
Keyboard/Mouse: One PS/2 Port to support PS/2 Mouse and PS/2 Key-
board
USB: One USB 2.0 compliant universal Serial bus port
1.3.6 Storage
• Supports a drive bay space for 2.5’’ HDD
• Supports a CompactFlash socket for Type I/II CompactFlash disk
1.3.7 Mechanical
Construction: Aluminum housing
Mounting: DIN-rail mounting, Desk/wall mounting
Dimension (W x H x D): 264.5 mm x 69.2 mm x 137.25 mm ( 10.41”x
2.72”x 4.4” )
Weight: Net 2 KG
1.3.8 Power Supply
• Output Rating 46 W
• Fuse Rating 7 A @ 125 V
• Input Voltage: 12 VDC ~ 24 VDC,
- Typical:
12 VDC @ 4.5A,
16 VDC @ 3.4 A,
19 VDC @ 2.9 A,
24 VDC @ 2.3 A
• Output Voltage:

5 Chapter1
+5 VDC @ 7 A
+12 VDC @ 0.5 A
+5VSB @ 1 A
1.3.9 Environment Specifications
Operating Temperature
• When System is equipped with Compact Flash Disk only: -20 to 60° C
• When System is equipped with 2.5-inch Hard Disk: 0 to 45° C
Relative humidity 95 % @ 40 ° C(non-condensing)
Vibration loading during operation
• When system is equipped with Compact Flash Disk only:
5Grms, IEC 68-2-64, random, 5~500Hz, 1 Oct./min, 1hr/axis.
• When system is equipped with 2.5-inch hard disk:
1Grms, IEC 68-2-64, random, 5~500Hz, 1 Oct./min, 1hr/axis.
Shock during operation
• When system is equipped with Compact Flash Disk only:
50Grms, IEC 68-2-27, half sine, 11 ms duration
• When system is equipped with Hard Disk:
20Grms, IEC 68-2-27, half sine, 11 ms duration
EMC Approved: CE, FCC Class A
Safety Approved: UL

ARK-3380 User Manual 6
1.4 Chassis Dimensions
Figure 1.1: Chassis Dimensions
69.20
53.00
傂10.00
傂2.00
傂6.00
264.50
71.36
7.81
111.51
224.00
61.20
8.20
3.50
8.00
232.00
240.00
69.20
媗11.31
8.00
5.96 2.66
71.66
119.51
125.76
252.50
69.20
69.00
5.00
10.00
14.00
31.38
78.50
92.50
88.50
68.50
132.25
137.25
媗4.00
4.00
媗5.00
媗4.00
媗8.00
10.00
14.00
8.00
4.00
5.00
68.63
137.25